Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260507 CYLINDER HEAD GASKET A

2TR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 17167 2.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 12229 7.REMOVE VENTILATION PIPE

a.
A356098E03
1.448,0.531 1.448,0.104 1.448,0.104 1.135,0.104 true 2.625,0.646 2.708,0.146 2.708,0.146 2.865,0.146 true 2.146,0.656 2.219,0.115 2.219,0.115 2.375,0.115 true 1.323,1.198 1.115,0.844 1.115,0.844 1.031,0.844 true 1.604,1.063 1.438,1.552 1.438,1.552 1.438,1.677 true 0.917,0.01 1.146,0.208 0.229,0.198 10 false *1 1.333,1.698 1.563,1.917 0.229,0.219 10 true *4 0.833,0.75 1.063,0.938 0.229,0.188 10 false *3 2.906,0.052 3.156,0.281 0.25,0.229 10 false *2 2.417,0.021 2.625,0.219 0.208,0.198 10 false *5

Slide the clip and disconnect the No. 1 water by-pass hose from throttle body with motor assembly.

Text in Illustration
*1 No. 1 Water By-pass Hose
*2 No. 1 Ventilation Hose
*3 No. 3 Ventilation Hose
*4 No. 3 Water By-pass Hose
*5 Ventilation Pipe


b.

Slide the clip and disconnect the No. 1 ventilation hose from the PCV valve sub-assembly.


c.

Slide the clip and disconnect the No. 3 ventilation hose from the ventilation pipe.


d.

Slide the clip and disconnect the No. 3 water by-pass hose from the cylinder head sub-assembly.


e.

Remove the bolt and ventilation pipe.


Hide 11302 8.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11204 9.REMOVE CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

Hide 13540 12.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13506 15.REMOVE CHAIN SUB-ASSEMBLY

Hide 16.REMOVE CAMSHAFT BEARING CAP

a.
U147709E04
0.49,1.885 0.677,2.094 0.188,0.208 10 true 2 0.667,0.938 0.896,1.156 0.229,0.219 10 false 12 2.146,0.208 2.385,0.438 0.24,0.229 10 false 13 0.958,1.813 1.188,2.01 0.229,0.198 10 false 11 0.219,0.594 0.375,0.792 0.156,0.198 10 false 3 2.802,0.208 2.969,0.406 0.167,0.198 10 false 5 0.51,0.156 0.677,0.375 0.167,0.219 10 false 1 0.979,0.219 1.125,0.427 0.146,0.208 10 false 9 2.823,1.823 2.99,2.063 0.167,0.24 10 false 7 1.323,0.906 1.552,1.094 0.229,0.188 10 false 20 1.76,1.125 1.99,1.313 0.229,0.188 10 false 18 1.531,0.208 1.75,0.406 0.219,0.198 10 false 17 1.552,1.823 1.792,2.021 0.24,0.198 10 false 19 2.167,1.823 2.385,2.021 0.219,0.198 10 false 15 1.865,0.927 2.083,1.135 0.219,0.208 10 false 16 0.208,1.438 0.385,1.635 0.177,0.198 10 false 4 3.052,1.063 3.198,1.25 0.146,0.188 10 false 6 1.177,1.125 1.427,1.333 0.25,0.208 10 false 10 2.406,1.135 2.635,1.333 0.229,0.198 10 false 14 2.521,0.948 2.656,1.156 0.135,0.208 10 false 8

Uniformly loosen and remove the 20 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



b.
A337665

Remove the 9 bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 17.REMOVE CAMSHAFT

a.
A336453

Remove the camshaft.


Hide 13512 18.REMOVE NO. 2 CAMSHAFT

a.
A336455

Remove the No. 2 camshaft.


Hide 13801 19.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A336447E04
2.615,0.24 2.271,0.24 2.271,0.24 1.99,0.438 false 2.281,1.385 2.854,1.385 true 0.594,1.146 0.823,1.146 0.823,1.146 1.302,0.74 true 2.646,0.146 2.875,0.354 0.229,0.208 10 false *1 2.896,1.292 3.125,1.5 0.229,0.208 10 false *2 0.385,1.052 0.594,1.25 0.208,0.198 10 false *3

Remove the 16 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.

Text in Illustration
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap

HINT:

Arrange the removed parts in the correct order.



Hide 13750 20.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 21.REMOVE VALVE STEM CAP

a.

Remove the 16 valve stem caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 22.DISCONNECT ENGINE WIRE

a.
A356063

Remove the 3 bolts and disconnect the engine wire from the cylinder head sub-assembly.


Hide 11101 23.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A356064

w/ Oil Cooler:

Remove the bolt and disconnect the No. 4 water by-pass pipe.


b.
A384511E01
1.708,0.26 1.927,0.458 0.219,0.198 10 false 10 1.75,1.76 1.906,1.958 0.156,0.198 10 false 9 2.344,0.26 2.5,0.458 0.156,0.198 10 false 8 1.125,1.771 1.281,1.969 0.156,0.198 10 false 7 2.375,1.76 2.531,1.958 0.156,0.198 10 false 6 1.135,0.26 1.292,0.458 0.156,0.198 10 false 5 3.01,1.75 3.167,1.948 0.156,0.198 10 false 4 0.51,0.271 0.667,0.469 0.156,0.198 10 true 3 3,0.26 3.156,0.458 0.156,0.198 10 false 2 0.5,1.75 0.719,1.969 0.219,0.219 10 true 1

Uniformly loosen the 10 cylinder head set bolts in the sequence shown in the illustration. Remove the 10 cylinder head set bolts and plate washers.

NOTICE:
·

Be careful not to drop plate washers into the cylinder head sub-assembly.

·

Head warpage or cracking could result from removing cylinder head set bolts in the incorrect order.




c.

Remove the cylinder head sub-assembly.


Hide 11115 24.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block.