Home › Engine / Hybrid System › 5L-E (LUBRICATION) › OIL PUMP
RM27T0E _51 Engine / Hybrid System _053688 5L-E LUBRICATION _0260695 OIL PUMP A

5L-E LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11301C 1.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A057640E04
0.75,1.542 1.583,1.542 true 0.427,1.458 0.771,1.667 0.344,0.208 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing belt case edge.

SST
09214-60010  


b.

Apply MP grease to the lip of the oil seal.


Hide 11301 2.INSTALL TIMING BELT CASE SUB-ASSEMBLY

a.

Place a new gasket on the cylinder block.


b.

Install the timing belt case with the 5 bolts.

Torque:
23 N*m (230 kgf*cm, 17 ft.*lbf)


Hide 15104 3.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

Torque:
for nut : 21 N*m (210 kgf*cm, 17 ft.*lbf)
for bolt : 18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 12101 4.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old packing (FIPG) material and do not drop any oil on the contact surfaces of the oil pan and cylinder block.

·

Using a gasket scraper, remove all the old packing (FIPG) material from the installation surface.

·

Thoroughly clean all components to remove all the loose material.

·

Using a non-residue solvent, clean both of the sealing surfaces.

NOTICE:

Do not use a solvent which will affect the painted surfaces.




b.
A227429E01
2.173,1.061 2.290,1.201 0.117,0.140 10 B 1.079,1.061 1.203,1.208 0.123,0.147 10 A 1.079,1.791 1.203,1.938 0.123,0.147 10 A 2.173,1.791 2.290,1.931 0.117,0.140 10 B 1.025,2.963 1.366,3.114 0.341,0.151 10 A - A 2.159,2.963 2.505,3.114 0.346,0.151 10 B - B 0.102,1.511 0.276,1.671 0.174,0.161 10 *a 3.162,1.511 3.343,1.669 0.181,0.158 10 *b 3.253,1.461 3.253,1.349 3.253,1.349 2.775,1.018 false 0.203,1.456 0.203,1.297 0.203,1.297 0.665,1.035 false 2.245,0.137 2.404,0.293 0.159,0.156 10 *1 1.87,0.43 2.06,0.239 2.06,0.239 2.198,0.239 false 1.113,2.385 1.304,2.194 1.304,2.194 1.441,2.194 false 1.489,2.092 1.648,2.248 0.159,0.156 10 *1 2.334,2.385 2.524,2.194 2.524,2.194 2.662,2.194 false 2.709,2.092 2.868,2.248 0.159,0.156 10 *1

Apply seal packing to the oil pan as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Application Specification:
Item Seal Packing Diameter Seal Packing Application Length
Dashed line 7.0 mm (0.276 in.) 128 mm (5.04 in.)
Continuous line 5.0 mm (0.197 in.) -


Text in Illustration
*1 Seal Packing
*a Timing Belt Case Contact Portion
*b Rear Oil Seal Retainer Contact Portion

HINT:
·

Do not apply an excessive amount to the surface, especially near the oil passages.

·

Parts must be assembled within 5 minutes of application. Otherwise the material must be removed and reapplied.




c.

Install the oil pan with the 16 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several steps.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13502 6.INSTALL NO. 2 TIMING BELT IDLER SUB-ASSEMBLY

Hide 13505 7.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 12311 12.INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET RH

Hide 12315 13.INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET LH

Hide 22100 17.INSTALL INJECTION PUMP ASSEMBLY

Hide 13568 18.INSTALL TIMING BELT

Hide 88431 19.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 20.INSTALL ENGINE ASSEMBLY