Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control switch operates 8 functions: SET, COAST, TAP-DOWN, RESUME, ACCEL, TAP-UP, CANCEL and MODE. The SET, TAP-DOWN and COAST functions and the RESUME, TAP-UP and ACCEL functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while pushing it in each arrow direction and turns off after releasing it. The internal contact point of the cruise control switch is turned on with the switch operation. The driving support ECU then reads the resistance value that has been changed by the switch operation to control MODE, SET, COAST, RESUME, ACCEL and CANCEL operations. The dynamic radar cruise control system has two cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode.

HINT:
·

The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic radar cruise control system.

·

The operation of the constant speed control mode is the same as the cruise control system.



WIRING DIAGRAM

E323819E03
0.208,1.771 0.802,1.927 0.594,0.156 10 false CANCEL 0.865,1.76 1.25,1.917 0.385,0.156 10 false -SET 1.396,1.76 1.781,1.917 0.385,0.156 10 false +RES 1.906,2.146 2.365,2.302 0.458,0.156 10 false MODE 1.979,1.5 2.542,1.656 0.563,0.156 10 false ON-OFF 2.625,1.625 2.917,1.833 0.292,0.208 10 false R/N 2.583,2.542 3,2.75 0.417,0.208 10 false ECC 4.729,2.542 5.042,2.677 0.313,0.135 10 false ECC 2.583,0.729 2.917,0.979 0.333,0.25 10 false CCS 3.01,0.729 3.167,0.917 0.156,0.188 10 false 3 3,1.615 3.167,1.823 0.167,0.208 10 false 2 2.99,2.552 3.104,2.688 0.115,0.135 10 false 1 5.417,0.625 5.583,0.833 0.167,0.208 10 false 1 5.417,1.469 5.531,1.604 0.115,0.135 10 false 7 5.417,2.406 5.667,2.667 0.25,0.26 10 false 2 4.792,1.615 5.063,1.75 0.271,0.135 10 false R/N 4.729,0.719 5.042,0.854 0.313,0.135 10 false CCS 5.344,0.844 5.75,1.083 0.406,0.24 10 false G40 5.344,1.76 5.667,2 0.323,0.24 10 false G40 5.344,2.667 5.677,2.823 0.333,0.156 10 false G40 4.229,2.448 4.417,2.667 0.188,0.219 10 false 4 4.208,2.656 4.427,2.927 0.219,0.271 10 false z7 4.229,1.521 4.396,1.75 0.167,0.229 10 false 1 4.208,1.75 4.573,2.104 0.365,0.354 10 false z7 4.219,0.615 4.417,0.833 0.198,0.219 10 false 3 4.208,0.844 4.521,1.115 0.313,0.271 10 false z7 6.333,2.333 6.667,2.542 0.333,0.208 10 false G56 6.281,0.833 6.75,1.083 0.469,0.25 10 false CCS 6.281,1.729 6.833,2 0.552,0.271 10 false CCHG 5.99,1.625 6.208,1.771 0.219,0.146 10 false 16 6.073,0.708 6.25,0.854 0.177,0.146 10 false 1 6.438,2.469 6.906,2.76 0.469,0.292 10 false ECM 4.469,3.073 5.417,3.5 0.948,0.427 10 false Spiral Cable Sub-assembly 3.219,3.115 4.177,3.458 0.958,0.344 10 false Cruise Control Switch Wire 0.823,3.052 2.198,3.198 1.375,0.146 10 false A 0.823,3.219 2.333,3.5 1.51,0.281 10 false Cruise Control Switch 0.073,0.01 1.031,0.219 0.958,0.208 12 false for 1GR-FE:

E326764E01
0.215,1.822 0.811,1.982 0.596,0.161 10 CANCEL 0.866,1.836 1.250,1.996 0.384,0.161 10 -SET 1.378,1.85 1.762,2.010 0.384,0.161 10 +RES 1.924,2.177 2.380,2.331 0.456,0.155 10 MODE 1.95,1.495 2.507,1.650 0.558,0.155 10 ON-OFF 2.625,1.628 2.892,1.768 0.267,0.140 10 R/N 2.585,2.546 2.898,2.685 0.313,0.140 10 ECC 4.724,2.539 5.037,2.678 0.313,0.140 10 ECC 2.571,0.724 2.884,0.864 0.313,0.140 10 CCS 3.008,0.724 3.117,0.864 0.110,0.140 10 3 3.001,1.623 3.110,1.763 0.110,0.140 10 2 2.987,2.557 3.096,2.697 0.110,0.140 10 1 5.419,0.621 5.529,0.761 0.110,0.140 10 1 5.419,1.464 5.529,1.604 0.110,0.140 10 7 5.419,2.405 5.529,2.545 0.110,0.140 10 2 4.796,1.616 5.063,1.756 0.267,0.140 10 R/N 4.724,0.719 5.038,0.859 0.313,0.140 10 CCS 5.344,0.814 5.630,0.956 0.286,0.141 10 G40 5.33,1.746 5.616,1.887 0.286,0.141 10 G40 5.33,2.642 5.616,2.784 0.286,0.141 10 G40 4.229,2.447 4.339,2.587 0.110,0.140 10 4 4.195,2.644 4.373,2.784 0.178,0.140 10 z7 4.25,1.519 4.360,1.659 0.110,0.140 10 1 4.216,1.725 4.380,1.865 0.164,0.140 10 z7 4.222,0.612 4.332,0.752 0.110,0.140 10 3 4.192,0.808 4.356,0.949 0.164,0.140 10 z7 5.864,1.742 6.278,1.889 0.414,0.147 10 G58 6.294,0.824 6.758,0.971 0.464,0.147 10 CCS 6.28,1.728 6.744,1.875 0.464,0.147 10 CCHG 5.915,0.607 6.129,0.750 0.214,0.143 10 14 5.957,1.511 6.164,1.654 0.207,0.143 10 9 6.422,2.33 6.756,2.467 0.334,0.137 10 ECM 4.469,3.073 5.521,3.491 1.052,0.417 10 Spiral Cable Sub-assembly 3.223,3.127 4.184,3.468 0.961,0.341 10 Cruise Control Switch Wire 0.827,3.09 2.199,3.234 1.372,0.144 10 A 0.827,3.258 2.199,3.402 1.372,0.144 10 Cruise Control Switch 0.07,0.014 1.103,0.226 1.033,0.211 12 for 1KD-FTV: 5.864,0.824 6.278,0.971 0.414,0.147 10 G57

E323819E04
0.219,1.781 0.813,1.938 0.594,0.156 10 false CANCEL 0.865,1.792 1.25,1.948 0.385,0.156 10 false -SET 1.396,1.792 1.781,1.948 0.385,0.156 10 false +RES 1.948,2.146 2.406,2.302 0.458,0.156 10 false MODE 1.948,1.5 2.51,1.656 0.563,0.156 10 false ON-OFF 2.625,1.625 2.896,1.76 0.271,0.135 10 false R/N 2.583,2.542 2.896,2.677 0.313,0.135 10 false ECC 4.719,2.542 5.031,2.677 0.313,0.135 10 false ECC 2.573,0.729 2.885,0.865 0.313,0.135 10 false CCS 3.01,0.729 3.125,0.865 0.115,0.135 10 false 3 3,1.625 3.115,1.76 0.115,0.135 10 false 2 2.99,2.552 3.104,2.688 0.115,0.135 10 false 1 5.417,0.625 5.531,0.76 0.115,0.135 10 false 1 5.417,1.469 5.531,1.604 0.115,0.135 10 false 7 5.417,2.406 5.531,2.542 0.115,0.135 10 false 2 4.75,1.615 5.021,1.75 0.271,0.135 10 false R/N 4.719,0.719 5.031,0.854 0.313,0.135 10 false CCS 5.344,0.813 5.625,0.958 0.281,0.146 10 false G40 5.344,1.719 5.625,1.865 0.281,0.146 10 false G40 5.344,2.646 5.625,2.792 0.281,0.146 10 false G40 4.229,2.448 4.344,2.583 0.115,0.135 10 false 4 4.198,2.646 4.375,2.781 0.177,0.135 10 false z7 4.25,1.521 4.365,1.656 0.115,0.135 10 false 1 4.219,1.729 4.385,1.865 0.167,0.135 10 false z7 4.219,0.615 4.333,0.75 0.115,0.135 10 false 3 4.188,0.813 4.354,0.948 0.167,0.135 10 false z7 6.313,2.344 6.729,2.49 0.417,0.146 10 false G185 6.292,0.823 6.76,0.969 0.469,0.146 10 false CCS 6.281,1.729 6.75,1.875 0.469,0.146 10 false CCHG 5.99,0.719 6.208,0.865 0.219,0.146 10 false 26 6.031,1.625 6.24,1.771 0.208,0.146 10 false 11 6.417,2.5 6.75,2.635 0.333,0.135 10 false ECM 4.469,3.063 5.521,3.479 1.052,0.417 10 false Spiral Cable Sub-assembly 3.219,3.125 4.177,3.469 0.958,0.344 10 false Cruise Control Switch Wire 0.823,3.094 2.198,3.24 1.375,0.146 10 false A 0.823,3.26 2.198,3.406 1.375,0.146 10 false Cruise Control Switch 0.073,0.01 1.104,0.219 1.031,0.208 12 false for 1GD-FTV:

CAUTION / NOTICE / HINT

NOTICE:

When the ECM is replaced with a new one, initialization must be performed (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>INITIALIZATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Use the Data List to check if the cruise control switch is functioning properly (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Radar Cruise
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control switch (Main CPU) signal / ON or OFF ON: Cruise control switch on
OFF: Cruise control switch off
-
Cancel Switch Cancel switch signal / ON or OFF ON: Cancel switch on
OFF: Cancel switch off
-
SET/COAST Switch -SET switch signal / ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal / ON or OFF ON: +RES switch on
OFF: +RES switch off
-

OK:

On screen, each item changes between ON and OFF according to above chart.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips in the connector or spiral cable.


E176804E07
2.064,1.153 2.380,1.295 0.316,0.142 10 CCS 1.606,1.153 1.922,1.295 0.316,0.142 10 ECC 2.258,1.145 2.083,0.875 false 2.329,0.861 2.11,0.712 false 1.803,1.145 1.978,0.875 false 0.733,4.264 1.049,4.406 0.316,0.142 10 CCS 1.667,4.261 1.934,4.403 0.267,0.142 10 R/N 2.35,0.789 2.617,0.931 0.267,0.142 10 R/N 1.188,4.264 1.504,4.406 0.316,0.142 10 ECC 1.362,4.256 1.187,3.922 false 0.917,4.256 1.091,3.922 false 0.917,4.256 1.091,3.922 false 1.112,3.756 1.82,4.264 false

c.

Check the spiral cable.

i.

Set the spiral cable to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

Rotate the spiral cable 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise and measure the resistance according to the value(s) in the table below.

NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.


Standard Resistance:
Tester Connection Condition Specified Condition
3 (CCS) - 1 (CCS) Always Below 1 Ω
4 (ECC) - 2 (ECC)
1 (R/N) - 7 (R/N)



iii.

Set the spiral cable to the center position and rotate the spiral cable 2.5 times clockwise. Then, while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CCS) - 1 (CCS) Always Below 1 Ω
4 (ECC) - 2 (ECC)
1 (R/N) - 7 (R/N)





OK

3.INSPECT CRUISE CONTROL SWITCH WIRE

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.INSPECT CRUISE CONTROL SWITCH WIRE
a.
U116450E01
0.601,3.161 0.915,3.301 0.314,0.140 10 ECC 1.461,3.161 1.775,3.301 0.314,0.140 10 CCS 1.065,3.161 1.323,3.301 0.259,0.140 10 R/N 1.275,1.465 1.589,1.606 0.314,0.140 10 ECC 0.73,1.465 1.044,1.606 0.314,0.140 10 CCS 1.394,2.692 1.643,3.146 false 1.038,2.692 0.79,3.146 false 1.271,1.125 1.451,1.449 false 1.103,1.125 0.913,1.449 false 1.08,0.107 1.252,0.245 0.172,0.138 10 z7 1.17,1.753 1.283,1.891 0.112,0.138 10 A 1.214,3.158 1.214,2.687 false 1.085,0.858 0.702,1.24 false 0.377,1.19 0.636,1.330 0.259,0.140 10 R/N

Disconnect the z7 spiral cable connector.


b.

Disconnect the A switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z7-3 (CCS) - A-3 (CCS) Always Below 2.5 Ω
z7-4 (ECC) - A-1 (ECC)
z7-1 (R/N) - A-2 (R/N)
z7-3 (CCS) - Body ground Always 1 MΩ or higher
z7-4 (ECC) - Body ground
z7-1 (R/N) - Body ground




OK

4.INSPECT CRUISE CONTROL SWITCH

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT CRUISE CONTROL SWITCH
a.

b.


OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the G40 spiral cable connector.


b.

Disconnect the G56*1, G57*2, G58*2 and G185*3 ECM connectors.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE
Tester Connection Condition Specified Condition
G40-1 (CCS) - G56-1 (CCS) Always Below 1 Ω
G40-7 (R/N) - G56-16 (CCHG)
G40-2 (ECC) - Body ground
G40-1 (CCS) - Body ground Always 10 kΩ or higher
G40-7 (R/N) - Body ground

for 1KD-FTV
Tester Connection Condition Specified Condition
G40-1 (CCS) - G57-14 (CCS) Always Below 1 Ω
G40-7 (R/N) - G58-9 (CCHG)
G40-2 (ECC) - Body ground
G40-1 (CCS) - Body ground Always 10 kΩ or higher
G40-7 (R/N) - Body ground

for 1GD-FTV
Tester Connection Condition Specified Condition
G40-1 (CCS) - G185-26 (CCS) Always Below 1 Ω
G40-7 (R/N) - G185-11 (CCHG)
G40-2 (ECC) - Body ground
G40-1 (CCS) - Body ground Always 10 kΩ or higher
G40-7 (R/N) - Body ground


Result
Result Proceed to
OK (for 1GR-FE) A
OK (for 1KD-FTV) B
OK (for 1GD-FTV) C
NG D



A

B

C

D

REPAIR OR REPLACE HARNESS OR CONNECTOR