Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 1GD-FTV) › 2015.06–2017.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260789 AUTOMATIC TRANSMISSION ASSEMBLY(for 1GD-FTV) A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1GD-FTV)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

(See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

(See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51450 4.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 37110 7.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 37140 8.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 28100 10.DISCONNECT STARTER ASSEMBLY

a.

for 2.0 kW Type:

i.
C326402

Remove the 2 bolts and nut and disconnect the starter assembly.

HINT:

Tie the starter assembly with a string.




b.

for 2.7 kW Type:

i.
A343736

Remove the bolt and 2 nuts and disconnect the starter assembly.

HINT:

Tie the starter assembly with a string.




Hide 12156 11.REMOVE OIL PAN INSULATOR

a.
C330328

Disconnect the 2 wire harness clamps.


b.

Remove the 2 bolts and oil pan insulator.


Hide 32101A 12.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C377335C01
1.573,0.438 1.667,0.302 1.667,0.302 1.823,0.302 false 2.604,1.01 2.698,1.135 2.698,1.135 2.854,1.135 false 1.625,0.771 1.719,0.635 1.719,0.635 1.875,0.635 false 0.521,1.104 0.615,0.969 0.615,0.969 0.771,0.969 false 0.49,0.635 0.656,0.771 0.656,0.771 0.813,0.771 false 0.865,0.667 1.177,0.823 0.313,0.156 10 false *a 1.917,0.563 2.229,0.719 0.313,0.156 10 false *b 0.823,0.885 1.135,1.042 0.313,0.156 10 false *c 1.896,0.229 2.188,0.396 0.292,0.167 10 false SST 2.948,1.063 3.24,1.229 0.292,0.167 10 false SST
*a Socket Adaptor (Square drive 12.7 to 9.5 mm)
(Tool No. 09022-3C110)
*b Socket Adaptor (Square drive 9.5 mm to 12.7 mm)
(Tool No. 09022-3C100)
*c 17 mm Socket Wrench
(Tool No. 09011-2C500)
V113147

Turn


Using SST, turn the crankshaft to gain access to the locations of the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored bolt.


SST
09961-01270  
09970-10010  (09970-00010)


Hide 33820B 13.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C323981

Remove the clip and nut and disconnect the transmission control cable assembly from the transmission control shaft lever LH and transmission control cable bracket.


Hide 15.DISCONNECT OIL COOLER TUBE

a.
C324534

Disconnect the 2 oil cooler tubes from the automatic transmission assembly.

HINT:

Use a container to catch any ATF.



b.

Remove the bolt and flexible hose clamp.

C330295E02
1.969,0.917 1.896,1.208 1.896,1.208 1.813,1.208 true 1.646,1.115 1.802,1.292 0.156,0.177 10 false *1

Text in Illustration
*1 Flexible Hose Clamp - -


c.

Remove the 2 bolts and disconnect the 2 oil cooler tubes from the automatic transmission assembly.


Hide 51225B 16.REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH

a.
C333241E02
0.094,0.031 0.354,0.26 0.26,0.229 10 false *A 0.094,2.396 0.313,2.635 0.219,0.24 10 false *B

Remove the 8 bolts, front suspension member bracket LH and RH from the No. 3 frame crossmember sub-assembly and vehicle body.

Text in Illustration
*A w/ Urea SCR System
*A w/o Urea SCR System


Hide 35000 17.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C330299

Support the automatic transmission assembly with a transmission jack.

NOTICE:
·

In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.

·

Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.

·

To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.

·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.




Hide 77801A 18.DISCONNECT UREA TANK SUB-ASSEMBLY

Hide 51203 19.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C330302

Remove the 4 bolts and disconnect the No. 3 frame crossmember sub-assembly from the rear No. 1 engine mounting insulator.


b.
C374939

w/ Urea SCR System:

Remove the 2 bolts as shown in the illustration, raise the urea tank sub-assembly and hold it in position.

HINT:

Only raise the urea tank enough to remove the fixing bolts on the No. 3 frame crossmember sub-assembly. Do not raise it any higher.



c.
C213724

Remove the 4 bolts, 4 nuts and No. 3 frame crossmember sub-assembly from the vehicle body.


d.
C374942

w/ Urea SCR System:

Temporarily install the urea tank sub-assembly with the bolt as shown in the illustration.


Hide 12371 20.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C330292

Remove the bolt and engine mounting heat insulator from the rear No. 1 engine mounting insulator.


b.
C330291

Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission assembly.


Hide 21.DISCONNECT WIRE HARNESS

a.
C330298

Tilt down the automatic transmission assembly.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.



b.
C333125

Disconnect the breather hose from the wire harness.


c.

Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer connector.

C333307

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



d.

Detach the 2 wire harness clamps.


e.

Remove the 4 bolts and disconnect the wire harness from the automatic transmission assembly.


Hide 35000 22.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C330329

Remove the 9 bolts and automatic transmission assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the automatic transmission assembly and engine assembly.



Hide 36478A 23.REMOVE TRANSMISSION BREATHER BRACKET

HINT:

It is not necessary to remove the transmission breather bracket unless it is being replaced.


a.
C332143

Disconnect the 3 breather hoses from the transmission breather bracket.


b.
C332144

Remove the bolt and transmission breather bracket from the automatic transmission assembly.


c.

Remove the 2 clamps from the transmission breather bracket.


Hide 33823 25.REMOVE TRANSMISSION CONTROL CABLE BRACKET

HINT:

It is not necessary to remove the transmission control cable bracket unless it is being replaced.


a.
C324529

Remove the 2 bolts and transmission control cable bracket from the automatic transmission assembly.


Hide 3516A 26.REMOVE TRANSMISSION OIL PAN HEAT INSULATOR

HINT:

It is not necessary to remove the transmission oil pan heat insulator unless it is being replaced.


a.
C330312

Remove the 3 bolts and transmission oil pan heat insulator from the automatic transmission assembly.


Hide 27.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C324532E02
1.719,0.24 1.125,0.146 1.125,0.146 1.719,0.438 true 0.927,0.021 1.083,0.198 0.156,0.177 10 false *a

Put matchmarks on the automatic transmission assembly and the torque converter assembly.

Text in Illustration
*a Matchmark


b.

Remove the torque converter assembly from the automatic transmission assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 28.REMOVE WIRE HARNESS CLAMP BRACKET

HINT:

It is not necessary to remove the wire harness clamp brackets unless they are being replaced.


a.
C330307

Detach the 8 wire harness clamps and 4 wire harness clamp brackets from the wire harness.