Home › Drivetrain › RA61F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053701 RA61F MANUAL TRANSMISSION / TRANSAXLE _0260824 MANUAL TRANSMISSION ASSEMBLY(for 1KD-FTV) A

RA61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for 1KD-FTV)  INSTALLATION  


PROCEDURE

Hide 33107 2.INSTALL TRANSMISSION UPPER COVER SUB-ASSEMBLY

a.

Install the transmission upper cover sub-assembly with the 2 bolts.

Torque:
12 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 3.INSTALL MANUAL TRANSMISSION WITH TRANSFER

a.

Install the manual transmission with transfer with the 9 bolts.

Torque:
72 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 36407 4.CONNECT TRANSFER AND MANUAL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.

Connect the 3 breather hoses.


b.

Attach the breather hose clamp.


Hide 5.CONNECT WIRE HARNESS

a.

Attach the 5 wire harness clamps.


b.

Connect the 2 connectors.


Hide 12371 6.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear No. 1 engine mounting insulator with the 4 bolts.

Torque:
73 N*m (739 kgf*cm, 54 ft.*lbf)


Hide 51204 7.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


b.

Install the 4 bolts to the No. 3 frame crossmember sub-assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 51226A 8.INSTALL FRONT SUSPENSION MEMBER BRACKET LH

a.

Install the front suspension member bracket LH with the 4 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


Hide 51225B 9.INSTALL FRONT SUSPENSION MEMBER BRACKET RH

a.

Install the front suspension member bracket RH with the 4 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


Hide 31470 11.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

a.

Connect the release cylinder with the 2 bolts.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


b.

Install a new clip to the flexible hose.


Hide 37110 12.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 37140 13.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 36179 14.INSTALL TRANSFER CASE LOWER PROTECTOR

a.

Install the transfer case lower protector with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 17410 15.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 16.ADD MANUAL TRANSMISSION OIL

Hide 33530F 18.INSTALL SHIFT LEVER ASSEMBLY

a.
F051066

Apply MP grease to the tip of the shift lever assembly.

Text in Illustration
V100135

MP Grease


b.

Cover the shift lever cap with a cloth.


c.
C329000E05
2.063,0.646 2.458,0.646 false 1.115,0.229 1.323,0.385 0.208,0.156 10 false *a 1.76,2.896 1.969,3.052 0.208,0.156 10 false *b 1.854,4.25 2.063,4.406 0.208,0.156 10 false *c 2.5,0.563 2.708,0.719 0.208,0.156 10 false *1

While pressing down on the shift lever cap, turn it clockwise to install the shift lever assembly.

Text in Illustration
*1 Shift Lever Cap
*a Press down
*b Clockwise
*c Lock


Hide 58286 19.INSTALL NO. 1 SHIFT AND SELECT LEVER BOOT

a.

Install the No. 1 shift lever boot with the 4 screws.


Hide 28800 21.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).