Home › Drivetrain › RA61F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for 1GD-FTV)
RM27T0E _52 Drivetrain _053701 RA61F MANUAL TRANSMISSION / TRANSAXLE _0260827 MANUAL TRANSMISSION ASSEMBLY(for 1GD-FTV) A

RA61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for 1GD-FTV)  REMOVAL  


PROCEDURE

Hide 28800 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 58286 3.REMOVE NO. 1 SHIFT AND SELECT LEVER BOOT

a.
C215612

Remove the 4 screws and No. 1 shift and select lever boot.


Hide 33530F 4.REMOVE SHIFT LEVER ASSEMBLY

F051062

a.

Detach the shift lever cap boot from the manual transmission.


b.

Cover the shift lever cap with a cloth.


c.
C328999E01
1.872,0.769 2.068,0.922 0.196,0.153 10 *a 1.735,2.328 1.930,2.481 0.196,0.153 10 *b 1.114,3.197 1.310,3.350 0.196,0.153 10 *c 2.004,0.474 2.248,0.23 2.248,0.23 2.411,0.23 false 2.474,0.136 2.670,0.289 0.196,0.153 10 *1

While pressing down on the shift lever cap, turn it counterclockwise, and then pull to remove the shift lever assembly.

Text in Illustration
*1 Shift Lever Cap
*a Press Down
*b Counterclockwise
*c Pull out


Hide 5.DRAIN BRAKE FLUID FROM CLUTCH LINE

Hide 6.DRAIN MANUAL TRANSMISSION OIL

a.

Remove the drain plug and gasket, and then drain the manual transmission oil.


b.

Install a new gasket and the drain plug.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 17410 7.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 36179 8.REMOVE TRANSFER CASE LOWER PROTECTOR

a.

Remove the 4 bolts and transfer case lower protector.


Hide 9.REMOVE WIRE HARNESS CLAMP BRACKET (w/ Urea SCR System)

a.
C332730

Detach the 3 wire harness clamps and disconnect the wire harness.


b.
C332731

Remove the bolt and wire harness clamp bracket.


Hide 10.DISCONNECT WIRE HARNESS (w/ Urea SCR System)

a.
C334344

Detach the 2 wire harness clamps and disconnect the wire harness.


Hide 12156 11.REMOVE OIL PAN INSULATOR

a.
C332732

Remove the 2 bolts and oil pan insulator.


Hide 37140 12.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 13.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 31482 14.REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

a.
C331842

Remove the 2 bolts, 3 nut, clip and clutch release cylinder to flexible hose tube.


b.
C334347

Remove the 2 bolts and clutch flexible hose bracket.


Hide 31470 15.REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 53737A 16.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH (w/ Urea SCR System)

Hide 28100 17.DISCONNECT STARTER ASSEMBLY (w/ Urea SCR System)

a.

for 2.0 kW Type:

Disconnect the starter.

i.

Open the terminal cap.


ii.
C322552

Remove the nut and disconnect the starter wire.


iii.

Disconnect the starter connector.


iv.

Remove the 2 bolts and disconnect the starter assembly.



b.

for 2.7 kW Type:

Disconnect the starter.

i.
A351933

Open the terminal cap.


ii.

Remove the nut and disconnect the starter wire.


iii.

Disconnect the starter connector.


iv.
A357294

Remove the 2 bolts and disconnect the starter assembly.



Hide 28100 18.REMOVE STARTER ASSEMBLY (w/o Urea SCR System)

Hide 51226A 19.REMOVE FRONT SUSPENSION MEMBER BRACKET LH

a.
C215587

Remove the 4 bolts and front suspension member bracket LH.


Hide 51226A 20.REMOVE FRONT SUSPENSION MEMBER BRACKET LH (w/ Urea SCR System)

a.
C334346

Remove the 4 bolts and front suspension member bracket LH.


Hide 51225B 21.REMOVE FRONT SUSPENSION MEMBER BRACKET RH

C215588

a.

Remove the 4 bolts and front suspension member bracket RH.


Hide 51204 22.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Support the rear side of the manual transmission with a support stand.


b.
C215589

Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.


c.
C374939

w/ Urea SCR System:

Remove the 2 bolts as shown in the illustration, raise the urea tank sub-assembly and hold it in position.

HINT:

Only raise the urea tank enough to remove the fixing bolts on the No. 3 frame crossmember sub-assembly. Do not raise it any higher.



d.
C215614

Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.


e.
C374942

w/ Urea SCR System:

Temporarily install the urea tank sub-assembly with the bolt as shown in the illustration.


Hide 12391 23.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
C332736

Remove the bolt and front engine mounting insulator RH.


Hide 12371 24.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C332737

Remove the 4 bolts and rear No. 1 engine mounting insulator from the manual transmission.


Hide 25.DISCONNECT WIRE HARNESS

a.
C215616

Detach the 5 wire harness clamps.


b.

Disconnect the 2 connectors and wire harness.


Hide 36407 26.DISCONNECT TRANSFER AND MANUAL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C215615

Detach the breather hose clamp.


b.

Disconnect the 3 breather hoses.


Hide 27.REMOVE MANUAL TRANSMISSION WITH TRANSFER

a.
C332733E01
0.093,0.101 0.545,0.479 0.452,0.378 10 *A 0.07,2.53 0.522,2.908 0.452,0.378 10 *B 3.135,3.725 3.322,3.902 0.187,0.177 10 *1 2.845,3.936 2.976,3.807 2.976,3.807 3.101,3.807 false

w/o Urea SCR System:

Remove the 9 bolts.

Text in Illustration
*A w/o Urea SCR System
*B w/ Urea SCR System
*1 Wire Harness Bracket


b.

w/ Urea SCR System:

Remove the 9 bolts and wire harness bracket.


c.

Remove the manual transmission with transfer.


Hide 33107 28.REMOVE TRANSMISSION UPPER COVER SUB-ASSEMBLY

C215595

a.

Remove the 2 bolts and transmission upper cover sub-assembly.