1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
33504F
2.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Remove the knob from the shift lever.
58821C
3.REMOVE CONSOLE PANEL SUB-ASSEMBLY
for Manual Transmission: (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Manual Transmission)>REMOVAL)
w/ Refrigerated Cool Box: (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX (w/ Refrigerated Cool Box)>REMOVAL)
58286
4.REMOVE NO. 1 SHIFT AND SELECT LEVER BOOT
Remove the 4 screws, 2 clips and shift and select lever boot.
| *1 | Clip |
| *2 | Screw |
33530F
5.REMOVE SHIFT LEVER ASSEMBLY
Detach the shift lever cap boot from the manual transmission.
Cover the shift lever cap with a cloth.
While pressing down on the shift lever cap, turn it counterclockwise, and then pull to remove the shift lever assembly.
| *1 | Shift Lever Cap |
| *a | Press Down |
| *b | Counterclockwise |
| *c | Pull out |
36179
6.REMOVE TRANSFER CASE LOWER PROTECTOR
Remove the 4 bolts and lower protector.
7.DRAIN MANUAL TRANSMISSION OIL
37140
8.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
Remove the front propeller shaft (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY>REMOVAL).
37110
9.REMOVE PROPELLER SHAFT ASSEMBLY
Remove the propeller shaft (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY>REMOVAL).
31470
10.DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY
Remove the 2 bolts and disconnect the release cylinder assembly.
28100
11.REMOVE STARTER ASSEMBLY
for 1.4 kW Type:
Remove the starter (See page Engine / Hybrid System>2TR-FE (STARTING)>STARTER (for 1.4 kW Type)>REMOVAL).
for 2.0 kW Type:
Remove the starter (See page Engine / Hybrid System>2TR-FE (STARTING)>STARTER (for 2.0 kW Type)>REMOVAL).
51226A
12.REMOVE FRONT SUSPENSION MEMBER BRACKET LH
Remove the 4 bolts and member bracket.
51225B
13.REMOVE FRONT SUSPENSION MEMBER BRACKET RH
Remove the 4 bolts and member bracket.
51204
14.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Support the rear side of the transmission with a support stand.
Remove the 4 bolts from the mounting insulator.
Remove the 4 bolts, 4 nuts and frame crossmember.
12371
15.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Remove the 5 bolts, front engine mounting insulator and mounting insulator.
17118
16.REMOVE MANIFOLD STAY
17.DISCONNECT WIRE HARNESS
Disconnect the 2 connectors and 4 clamps.
36407
18.DISCONNECT TRANSFER AND MANUAL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY
Disconnect the 3 breather hoses from the transfer adapter and transfer.
Disconnect the 2 breather hoses from the bracket.
33030
19.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
Using a transmission jack, support the transmission.
Remove the support stand from the transmission.
Remove the 8 bolts and transmission unit.
36100
20.REMOVE TRANSFER ASSEMBLY