Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1713/13  Rear Height Control Sensor RH Circuit Malfunction  C1714/14  Rear Height Control Sensor LH Circuit Malfunction  


DESCRIPTION

The height control sensor changes its resistance value based on changes in vehicle height. The suspension control ECU outputs a fixed voltage of 5 V to the SHB terminal of the height control sensor. If the resistance value of the sensor changes, the voltage value of the sensor changes accordingly. The suspension control ECU then inputs the voltage value from the sensor to detect the vehicle height change.

DTC Code DTC Detection Condition Trouble Area
C1713/13 Either condition is met:
·

With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the rear height control sensor RH is detected for 0.5 seconds.

·

With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the rear height control sensor RH is detected for 1 second.


·

Harness or connector

·

Rear height control sensor RH

·

Suspension control ECU


C1714/14 Either condition is met:
·

With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the rear height control sensor LH is detected for 0.5 seconds.

·

With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the rear height control sensor LH is detected for 1 second.


·

Harness or connector

·

Rear height control sensor LH

·

Suspension control ECU



WIRING DIAGRAM

C216922E09
0.24,2.302 0.563,2.49 0.323,0.188 10 false S6 0.25,2.448 2.198,2.677 1.948,0.229 10 false Rear Height Control Sensor LH 1.542,1.677 1.698,1.885 0.156,0.208 10 false 3 5.344,5.198 6.938,5.5 1.594,0.302 10 false Suspension Control ECU 1.542,1.094 1.698,1.302 0.156,0.208 10 false 2 1.542,0.5 1.698,0.708 0.156,0.208 10 false 1 5.604,0.521 5.792,0.688 0.188,0.167 10 false 14 5.604,1.094 5.823,1.302 0.219,0.208 10 false 24 5.917,0.615 6.344,0.823 0.427,0.208 10 false SBL2 5.917,1.208 6.344,1.417 0.427,0.208 10 false SHRL 5.917,1.802 6.344,2.01 0.427,0.208 10 false SGL2 1.042,0.615 1.396,0.823 0.354,0.208 10 false SHB 1.042,1.229 1.469,1.438 0.427,0.208 10 false SHRL 1.042,1.823 1.396,2.031 0.354,0.208 10 false SHG 5.917,3.354 6.344,3.563 0.427,0.208 10 false SBR2 5.917,3.948 6.344,4.156 0.427,0.208 10 false SHRR 5.917,4.542 6.344,4.75 0.427,0.208 10 false SGR2 5.604,1.688 5.823,1.896 0.219,0.208 10 false 15 5.604,3.24 5.823,3.448 0.219,0.208 10 false 13 5.604,3.833 5.823,4.042 0.219,0.208 10 false 26 5.604,4.427 5.823,4.635 0.219,0.208 10 false 16 1.552,4.417 1.708,4.625 0.156,0.208 10 false 3 1.552,3.823 1.708,4.031 0.156,0.208 10 false 2 1.552,3.24 1.708,3.448 0.156,0.208 10 false 1 1.021,3.354 1.458,3.563 0.438,0.208 10 false SHB 1.021,3.958 1.458,4.167 0.438,0.208 10 false SHRR 1.021,4.552 1.385,4.76 0.365,0.208 10 false SHG 0.24,5.031 0.563,5.219 0.323,0.188 10 false S3 0.24,5.198 2.229,5.427 1.99,0.229 10 false Rear Height Control Sensor RH 5.354,5.021 5.656,5.198 0.302,0.177 10 false R19

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.INSPECT REAR HEIGHT CONTROL SENSOR
C214173E15
1.865,1.563 1.969,1.563 1.969,1.563 2.021,2.177 false 5.625,2.208 5.688,0.99 5.688,0.99 5.865,0.99 false 5.802,2.198 6,1.646 6,1.646 6.198,1.646 false 5.75,2.448 6.458,2.583 6.458,2.583 6.458,2.875 false 4.99,0.24 5.271,0.51 0.281,0.271 10 false *a 1.688,1.469 1.927,1.802 0.24,0.333 10 false *1 3.406,0.333 3.635,0.531 0.229,0.198 10 false *b 4.354,1.958 4.594,2.188 0.24,0.229 10 false *c 3.896,3.792 4.177,4.063 0.281,0.271 10 false *d 5.906,0.906 6.615,1.281 0.708,0.375 10 false SHRR*A, SHRL*B 6.229,1.563 6.583,1.74 0.354,0.177 10 false SHB 6.302,2.885 6.719,3.104 0.417,0.219 10 false SHG

Text in Illustration
*A for RH *B for LH
*1 Rear Height Control Sensor - -
*a Component without harness connected
(Rear Height Control Sensor)
*b Min. Low
*c Normal *d Max. High
V100135

45°
V100136

45°

a.

Check the rear height control sensor RH (when DTC C1713/13 is output).

i.

Remove the rear height control sensor RH (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL SENSOR>REMOVAL).


ii.

Connect 3 dry cell batteries of 1.5 V in series.


iii.

Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 3 (SHG).


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (SHG) - 2 (SHRR) Max. High (45°) 4.4 to 4.6 V
Normal (0°) 2.3 to 2.6 V
Min. Low (-45°) 0.4 to 0.6 V


NOTICE:

Do not apply a voltage of 5 V or higher.




b.

Check the rear height control sensor LH (when DTC C1714/14 is output).

i.

Remove the rear height control sensor LH (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL SENSOR>REMOVAL).


ii.

Connect 3 dry cell batteries of 1.5 V in series.


iii.

Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRL) and terminal 3 (SHG).


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (SHG) - 2 (SHRL) Max. High (45°) 4.4 to 4.6 V
Normal (0°) 2.3 to 2.6 V
Min. Low (-45°) 0.4 to 0.6 V


NOTICE:

Do not apply a voltage of 5 V or higher.




Result
Result Proceed to
OK A
NG (Rear height control sensor RH) B
NG (Rear height control sensor LH) C


A

2.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR - SUSPENSION CONTROL ECU)

B

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

C

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

2.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR - SUSPENSION CONTROL ECU)
a.

Check the rear height control sensor RH (when DTC C1713/13 is output).

i.

Disconnect the S3 rear height control sensor RH connector.


ii.

Disconnect the R19 suspension control ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S3-3 (SHG) - R19-16 (SGR2) Always Below 1 Ω
S3-2 (SHRR) - R19-26 (SHRR) Always Below 1 Ω
S3-1 (SHB) - R19-13 (SBR2) Always Below 1 Ω
S3-3 (SHG) - Body ground Always 10 kΩ or higher
S3-2 (SHRR) - Body ground Always 10 kΩ or higher
S3-1 (SHB) - Body ground Always 10 kΩ or higher




b.

Check the rear height control sensor LH (when DTC C1714/14 is output).

i.

Disconnect the S6 rear height control sensor LH connector.


ii.

Disconnect the R19 suspension control ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-3 (SHG) - R19-15 (SGL2) Always Below 1 Ω
S6-2 (SHRL) - R19-24 (SHRL) Always Below 1 Ω
S6-1 (SHB) - R19-14 (SBL2) Always Below 1 Ω
S6-3 (SHG) - Body ground Always 10 kΩ or higher
S6-2 (SHRL) - Body ground Always 10 kΩ or higher
S6-1 (SHB) - Body ground Always 10 kΩ or higher





OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR