Home › Suspension › SUSPENSION CONTROL › KINETIC DYNAMIC SUSPENSION SYSTEM › 2015.06–2021.06
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260886 KINETIC DYNAMIC SUSPENSION SYSTEM C

SUSPENSION CONTROL  KINETIC DYNAMIC SUSPENSION SYSTEM  C1851/51  Low Pressure Malfunction in Upside of KDSS System  C1853/53  High Pressure Malfunction in Upside of KDSS System  


DESCRIPTION

In the KDSS hydraulic circuit, the fluid is contained under pressure. If the fluid temperature is 20°C (68°F), the pressure is approximately 3.0 MPa (30.6 kgf/cm2, 435 psi).

DTC Code DTC Detection Condition Trouble Area
C1851/51 The sensor output is 0.9 MPa (9.2 kgf/cm2, 130 psi) or less for 5 min. continuously with the ignition switch ON.
·

Hydraulic circuit

·

Harness or connector

·

Accumulator pressure sensor or stabilizer control solenoid valve (Stabilizer control with accumulator housing assembly)

·

Stabilizer control ECU


C1853/53 The sensor output is 8.8 MPa (89.7 kgf/cm2, 1276 psi) or more for 20 sec. continuously with the ignition switch ON.

CAUTION / NOTICE / HINT

HINT:
·

When these DTCs are output, perform the hydraulic circuit inspection first (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL SYSTEM (w/ KDSS)>ON-VEHICLE INSPECTION).

·

If the DTCs cannot be cleared even after the hydraulic circuit inspection, perform the electrical circuit inspection by following the procedures below.



PROCEDURE

1.INSPECT FOR FLUID LEAK
a.

Inspect for fluid leaks (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL SYSTEM (w/ KDSS)>ON-VEHICLE INSPECTION).

OK:

No fluid leaks.




OK

2.CHECK ANY OTHER DTCS OUTPUT (DTC C1812/12, C1831/31 AND/OR C1832/32)

NG

REPAIR FLUID LEAK OR REPLACE PARTS AS NECESSARY

2.CHECK ANY OTHER DTCS OUTPUT (DTC C1812/12, C1831/31 AND/OR C1832/32)
a.

Check if DTC C1812/12, C1831/31 and/or C1832/32 is output (See page Suspension>SUSPENSION CONTROL>KINETIC DYNAMIC SUSPENSION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
No output A
DTC C1812/12, C1831/31 and/or C1832/32 is output B



A

3.INSPECT STABILIZER CONTROL SOLENOID VALVE (CHECK IF VALVE STUCK)

B

3.INSPECT STABILIZER CONTROL SOLENOID VALVE (CHECK IF VALVE STUCK)
a.

Disconnect the Stabilizer control with accumulator housing assembly connector.


b.

Check for an operating sound of the Stabilizer control solenoid valve.

i.
C215165E01
0.164,0.114 0.429,0.386 0.266,0.272 10 *a 0.172,0.675 0.544,0.827 0.371,0.152 10 SLAL 2.085,0.46 2.456,0.612 0.371,0.152 10 AUG 0.632,0.768 0.924,0.768 0.924,0.768 1.368,1.26 false 2.033,0.547 1.732,0.547 1.732,0.547 1.652,1.269 false

for Upper Chamber:

Connect terminal 5 (SLAL) to the positive (+) battery terminal, and terminal 4 (AUG) to the negative (-) battery terminal.

OK:

An operating sound (click sound) can be heard.


Text in Illustration
*a Component without harness connected
(Stabilizer Control with Accumulator Housing Assembly)


ii.
C215164E01
0.123,0.131 0.399,0.352 0.276,0.221 10 *a 0.176,0.748 0.603,0.904 0.427,0.156 10 SLAU 2.092,0.447 2.519,0.603 0.427,0.156 10 AUG 0.683,0.836 0.807,0.836 0.807,0.836 1.137,1.272 false 2.056,0.544 1.716,0.544 1.716,0.544 1.667,1.272 false

for Lower Chamber:

Connect terminal 6 (SLAU) to the positive (+) battery terminal, and terminal 4 (AUG) to the negative (-) battery terminal.

OK:

An operating sound (click sound) can be heard.


Text in Illustration
*a Component without harness connected
(Stabilizer Control with Accumulator Housing Assembly)




OK

4.INSPECT FOR CLOGS IN HYDRAULIC CIRCUIT

NG

REPLACE STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY

4.INSPECT FOR CLOGS IN HYDRAULIC CIRCUIT
a.

Bleed air and check that the hydraulic circuit is not clogged (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL SYSTEM (w/ KDSS)>BLEEDING).

OK:

Hydraulic circuit is not clogged.




OK

5.RECONFIRM DTC

NG

REPAIR HYDRAULIC CIRCUIT MALFUNCTIONS OR REPLACE PARTS AS NECESSARY

5.RECONFIRM DTC

b.

Check for DTCs (See page Suspension>SUSPENSION CONTROL>KINETIC DYNAMIC SUSPENSION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

REPLACE STABILIZER CONTROL ECU