Home › Suspension › SUSPENSION CONTROL › STABILIZER CONTROL TUBE (w/ KDSS) › 2015.06–2020.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260887 STABILIZER CONTROL TUBE(w/ KDSS) A

SUSPENSION CONTROL  STABILIZER CONTROL TUBE(w/ KDSS)  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 2.REMOVE FRONT WHEEL LH

Hide 3.REMOVE REAR WHEEL LH

Hide 4.REMOVE SPARE TIRE

Hide 51405A 7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 48826D 9.REMOVE STABILIZER CONTROL VALVE PROTECTOR

a.
C212853

Remove the 2 bolts and stabilizer control valve protector.


Hide 10.DRAIN SUSPENSION FLUID

a.
C212854

Loosen the bleeder plug on the stabilizer control with accumulator housing assembly and drain suspension fluid.

HINT:
·

Drain suspension fluid when performing operations related to the hydraulic circuits.

·

Draining suspension fluid decreases suspension fluid pressure.




b.

Tighten the bleeder plug.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


Hide 48827D 11.REMOVE FRONT STABILIZER TUBE PROTECTOR

a.

Remove the 2 bolts and front stabilizer tube protector.

C337770E01
0.173,0 0.398,0.198 0.224,0.198 12 *A 3.69,0 3.914,0.198 0.224,0.198 12 *B

Text in Illustration
*A for 1GR-FE *B for 1KD-FTV


Hide 896B1 12.REMOVE UREA PUMP CONTROL ECU (for 1GD-FTV)

Hide 48890 13.REMOVE FRONT STABILIZER CONTROL TUBE INSULATOR

a.

for 1GR-FE:

Remove the 2 bolts and front stabilizer control tube insulator.

NOTICE:

When replacing the front No. 1 stabilizer control tube assembly, do not install the front stabilizer control tube insulator as it becomes unnecessary.



b.

for 1KD-FTV:

Remove the 3 bolts and front stabilizer control tube insulator.

NOTICE:

When replacing the front No. 1 stabilizer control tube assembly, do not install the front stabilizer control tube insulator as it becomes unnecessary.


C337261E01
0.249,0 0.470,0.221 0.221,0.221 12 *A 3.528,0 3.748,0.221 0.221,0.221 12 *B

Text in Illustration
*A for 1GR-FE *B for 1KD-FTV


Hide 48890 14.DISCONNECT FRONT NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

a.

When disconnecting the front No. 1 stabilizer control tube assembly before replacement:

C335215E01
0.127,0.155 0.362,0.352 0.236,0.198 12 *A 0.125,2.158 0.361,2.355 0.236,0.198 12 *B 0.125,4.189 0.361,4.387 0.236,0.198 12 *C 0.509,1.079 0.215,1.079 false 0.05,1.002 0.212,1.149 0.163,0.147 10 *2 0.483,3.009 0.189,3.009 false 0.023,2.932 0.186,3.079 0.163,0.147 10 *2 0.508,4.88 0.215,4.88 false 0.049,4.803 0.212,4.949 0.163,0.147 10 *2 6.296,0.344 5.63,0.344 false 5.465,0.267 5.627,0.414 0.163,0.147 10 *1 6.265,2.246 5.599,2.246 false 5.433,2.169 5.596,2.315 0.163,0.147 10 *1 6.44,4.09 5.775,4.09 false 5.609,4.014 5.772,4.160 0.163,0.147 10 *1

Text in Illustration
*A for 1GR-FE *B for 1KD-FTV
*C for 1GD-FTV - -
*1 Stabilizer Control with Accumulator Housing Assembly *2 Front Stabilizer with Tube Cylinder Assembly

i.

Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.


ii.

Using a union nut wrench, disconnect the 2 flare nuts from the front stabilizer with tube cylinder assembly.



b.

When disconnecting the front No. 1 stabilizer control tube assembly after replacement:

C335216E01
0.141,0.135 0.370,0.322 0.229,0.187 12 *A 0.138,2.028 0.367,2.216 0.229,0.187 12 *B 0.072,0.954 0.239,1.112 0.167,0.158 10 *2 0.493,1.025 0.232,1.025 false 5.534,0.218 5.701,0.376 0.167,0.158 10 *1 6.278,0.283 5.674,0.283 false 0.067,2.877 0.234,3.035 0.167,0.158 10 *2 0.489,2.948 0.227,2.948 false 5.682,2.054 5.849,2.212 0.167,0.158 10 *1 6.426,2.119 5.822,2.119 false

Text in Illustration
*A for 1GR-FE *B for 1KD-FTV, for 1GD-FTV
*1 Stabilizer Control with Accumulator Housing Assembly *2 Front Stabilizer with Tube Cylinder Assembly

i.

Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.


ii.

Using a union nut wrench, disconnect the 2 flare nuts from the front stabilizer with tube cylinder assembly.


iii.

Using a union nut wrench, disconnect the 2 flare nuts.



Hide 48890 15.REMOVE FRONT NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

a.

When removing the front No. 1 stabilizer control tube assembly before replacement:

C335217E01
0.109,0.082 0.376,0.307 0.267,0.225 12 *A 0.146,2.835 0.413,3.061 0.267,0.225 12 *B 0.166,6.037 0.433,6.262 0.267,0.225 12 *C 1.014,0.172 1.182,0.324 0.167,0.152 10 *2 5.678,0.283 5.845,0.435 0.167,0.152 10 *1 5.644,2.951 5.811,3.103 0.167,0.152 10 *1 5.806,6.167 5.973,6.319 0.167,0.152 10 *1 3.103,0.755 3.272,0.911 0.170,0.156 10 *a 2.654,1.397 2.824,1.553 0.170,0.156 10 *a 3.014,3.455 3.184,3.611 0.170,0.156 10 *a 2.749,4.141 2.918,4.297 0.170,0.156 10 *a 3.19,6.854 3.359,7.010 0.170,0.156 10 *a 2.807,7.309 2.976,7.464 0.170,0.156 10 *a 0.596,0.439 0.754,0.252 0.754,0.252 0.988,0.252 false 1.027,2.878 1.195,3.031 0.167,0.152 10 *2 0.608,3.145 0.766,2.958 0.766,2.958 1.001,2.958 false 1.002,6.098 1.170,6.251 0.167,0.152 10 *2 0.583,6.366 0.741,6.178 0.741,6.178 0.976,6.178 false 6.405,0.352 5.824,0.352 false 6.393,3.021 5.794,3.021 false 6.532,6.24 5.956,6.24 false

Text in Illustration
*A for 1GR-FE *B for 1KD-FTV
*B for 1GD-FTV - -
*1 Stabilizer Control with Accumulator Housing Assembly *2 Front Stabilizer with Tube Cylinder Assembly
*a Cut Position - -

i.

Using a hacksaw, cut the front No. 1 stabilizer control tube assembly at the position shown in the illustration.

CAUTION:
·

Do not cut your fingers, etc.

·

Wear protective goggles.



NOTICE:
·

Wrap protective tape around the cut ends of the front No. 1 stabilizer control tube assembly.

·

Use a piece of cloth to protect the body from becoming damaged.




ii.

for 1GR-FE:

1.

Remove the bolt and front No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).

2.

Remove the bolt and front No. 1 stabilizer control tube assembly (front stabilizer with tube cylinder assembly side).

NOTICE:

Make sure that the drive shaft boot is not damaged during removal.




iii.

for 1KD-FTV:

1.

Remove the 2 bolts and front No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).

2.

Remove the bolt and front No. 1 stabilizer control tube assembly (front stabilizer with tube cylinder assembly side).

NOTICE:

Make sure that the drive shaft boot is not damaged during removal.




iv.

for 1GD-FTV:

1.

Remove the 2 bolts and front No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).

2.

Remove the bolt and front No. 1 stabilizer control tube assembly (front stabilizer with tube cylinder assembly side).

NOTICE:

Make sure that the drive shaft boot is not damaged during removal.





b.

When removing the front No. 1 stabilizer control tube assembly after replacement:

C335218E01
0.16,0.147 0.393,0.344 0.232,0.198 12 *A 0.16,3.186 0.393,3.383 0.232,0.198 12 *B 0.61,1.246 0.957,1.246 0.957,1.246 0.957,1.897 false 0.889,1.911 1.059,2.072 0.170,0.161 10 *2 6.236,0.379 5.727,0.379 false 5.563,0.3 5.732,0.461 0.170,0.161 10 *1 0.509,4.186 0.856,4.186 0.856,4.186 0.856,4.838 false 0.788,4.852 0.958,5.012 0.170,0.161 10 *2 6.283,3.276 5.774,3.276 false 5.61,3.197 5.780,3.357 0.170,0.161 10 *1

Text in Illustration
*A for 1GR-FE *B for 1KD-FTV, for 1GD-FTV
*1 Stabilizer Control with Accumulator Housing Assembly *2 Front Stabilizer with Tube Cylinder Assembly

i.

Remove the bolt and front No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).


ii.

Remove the bolt (labeled A) and clamp from the front No. 1 stabilizer control tube assembly.

C335219E01
2.421,2.119 1.606,2.119 false 1.429,2.044 1.609,2.210 0.180,0.166 10 *1 2.417,4.895 1.602,4.895 false 1.425,4.819 1.605,4.986 0.180,0.166 10 *1 4.882,0.463 5.017,0.614 0.135,0.151 10 A 4.321,2.512 4.456,2.662 0.135,0.151 10 B 4.83,3.369 4.965,3.519 0.135,0.151 10 A 4.383,5.256 4.518,5.406 0.135,0.151 10 B 1.606,0.705 1.882,0.926 0.276,0.221 12 *A 1.596,3.902 1.873,4.123 0.276,0.221 12 *B

Text in Illustration
*A for 1GR-FE *B for 1KD-FTV, for 1GD-FTV
*1 Front Stabilizer with Tube Cylinder Assembly - -


iii.

Remove the bolt (labeled B), and then disconnect the front No. 1 stabilizer control tube assembly (front stabilizer with tube cylinder assembly side).


iv.

Remove the front No. 1 stabilizer control tube assembly (lower part) and front No. 1 stabilizer control tube assembly (upper part).

C335220E02
0.896,2.5 1.521,2.5 false 2.219,1.219 2.625,1.021 2.625,1.021 2.979,1.021 true 4.531,2.417 4.854,2.615 4.854,2.615 5.167,2.615 false 4.479,5.219 4.802,5.656 4.802,5.656 5.115,5.656 true 0.667,5.469 0.948,5.625 0.948,5.625 1.365,5.625 false 2.01,4.083 2.188,3.896 2.188,3.896 3.115,3.896 true 0.125,0.125 0.375,0.354 0.25,0.229 12 false *A 0.125,3.094 0.375,3.323 0.25,0.229 12 false *B 1.563,2.427 1.729,2.573 0.167,0.146 10 false *1 2.99,0.948 3.156,1.094 0.167,0.146 10 false *2 5.198,2.531 5.365,2.677 0.167,0.146 10 false *2 1.396,5.563 1.563,5.708 0.167,0.146 10 false *1 3.167,3.823 3.333,3.969 0.167,0.146 10 false *2 5.146,5.573 5.313,5.719 0.167,0.146 10 false *2

Text in Illustration
*A for 1GR-FE *B for 1KD-FTV, for 1GD-FTV
*1 Front No. 1 Stabilizer Control Tube Assembly (Upper Part) *2 Front No. 1 Stabilizer Control Tube Assembly (Lower Part)



Hide 89570A 16.REMOVE FUEL PUMP CONTROL ECU ASSEMBLY

Hide 48540 17.REMOVE REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48880 18.DISCONNECT REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

a.

When disconnecting the rear No. 1 stabilizer control tube assembly before replacement:

i.
C301670

Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.


ii.
C301139

Remove the 2 union bolts of the rear stabilizer control cylinder and the 2 pressure port gaskets.



b.

When disconnecting the rear No. 1 stabilizer control tube assembly after replacement:

C301137

i.

Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.


ii.

Using a union nut wrench, disconnect the 2 flare nuts.


iii.
C301139

Remove the 2 union bolts of the rear stabilizer control cylinder and the 2 pressure port gaskets.



Hide 48880 19.REMOVE REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

a.

When removing the rear No. 1 stabilizer control tube assembly before replacement:

C300799E01
1.017,2.994 1.017,1.647 1.017,1.647 0.882,1.647 false 0.728,1.573 0.907,1.747 0.179,0.174 10 *1 6.009,0.491 5.184,0.491 false 5.035,0.412 5.214,0.586 0.179,0.174 10 *2 4.389,1.978 4.578,2.135 0.188,0.157 10 *a 4.824,2.578 5.012,2.735 0.188,0.157 10 *a

Text in Illustration
*1 Stabilizer Control with Accumulator Housing Assembly *2 Rear Stabilizer Control Cylinder
*a Cut Position - -

i.

Remove the 5 bolts and disconnect the rear No. 1 stabilizer control tube assembly.


ii.

Using a hacksaw, cut the rear No. 1 stabilizer control tube assembly at the position shown in the illustration.

CAUTION:
·

Do not cut your fingers, etc.

·

Wear protective goggles.



NOTICE:
·

Cut the rear No. 1 stabilizer control tube assembly while securely holding down the cut position.

·

Use a piece of cloth to protect the body from becoming damaged.

·

Wrap protective tape around the cut ends of the rear No. 1 stabilizer control tube assembly.




iii.

Remove the cut rear No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).


iv.

Using a plastic-faced hammer, lightly tap the cut rear No. 1 stabilizer control tube assembly (rear stabilizer control cylinder side) while sliding it to the right to remove it.

C301655

HINT:

Performing this procedure with 2 persons may make the removal easier.




b.

When removing the rear No. 1 stabilizer control tube assembly after replacement:

C301892E01
1.05,2.783 1.05,1.543 1.05,1.543 1.218,1.543 false 1.26,1.468 1.449,1.647 0.188,0.179 10 *1 5.849,0.321 4.599,0.321 false 4.434,0.245 4.622,0.424 0.188,0.179 10 *2 1.853,2.958 2.009,3.127 0.156,0.170 10 A 4.197,1.968 4.352,2.137 0.156,0.170 10 B 2.776,2.325 2.932,2.495 0.156,0.170 10 A 5.67,1.16 5.826,1.329 0.156,0.170 10 B 6.665,0.809 6.821,0.979 0.156,0.170 10 B

Text in Illustration
*1 Stabilizer Control with Accumulator Housing Assembly *2 Rear Stabilizer Control Cylinder

i.

Remove the 2 bolts (labeled A) and disconnect the rear No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).


ii.

Remove the 3 bolts (labeled B) and disconnect the rear No. 1 stabilizer control tube assembly (rear stabilizer control cylinder side).


iii.

Using a plastic-faced hammer, lightly tap the rear No. 1 stabilizer control tube assembly (rear stabilizer control cylinder side) while sliding it to the right to remove it.

C301815E04
0.938,0.938 1.094,1.135 0.156,0.198 10 false A 4.302,3.74 4.458,3.938 0.156,0.198 10 false B

NOTICE:

Make sure that the rear No. 1 stabilizer control tube assembly is not deformed, as the gaps shown by arrows A and B in the illustration are small.


HINT:

Performing this procedure with 2 persons may make the removal easier.