Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  


DESCRIPTION

The skid control ECU receives signals from the acceleration sensor via the CAN communication system.

The acceleration sensor detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the acceleration sensor and the CAN communication system, DTC U0124 (malfunction in CAN communication with the acceleration sensor) are stored.

These DTCs are also stored when calibration has not been completed.

DTC C1279 can be cleared when the acceleration sensor sends an acceleration signal or test mode ends. DTC C1279 is stored only in test mode.

DTC Code DTC Detection Condition Trouble Area
C1243 While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change by 0.0294 G or more occurs 16 times or more.
·

ECU-IG NO. 1 fuse

·

Acceleration sensor

·

Acceleration sensor circuit

·

Sensor installation

·

CAN communication system


C1245 At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
C1279 Stored only during test mode.

WIRING DIAGRAM

C185399E08
0.366,1.487 3.328,1.740 2.961,0.253 10 Brake Actuator Assembly (Skid Control ECU) 0.759,2.366 3.033,2.543 2.274,0.177 10 : CAN Communication System 4.999,2.197 6.340,2.360 1.341,0.163 10 Acceleration Sensor 0.366,1.317 0.578,1.486 0.211,0.170 10 A6 3.785,0.387 4.746,0.536 0.961,0.149 10 ECU-IG NO. 1 1.875,0.163 2.943,0.360 1.068,0.198 10 from IG1 Circuit 5.592,0.744 5.880,0.984 0.288,0.239 10 IG 6.02,1.389 6.412,1.552 0.392,0.163 10 GND 5.746,0.45 5.934,0.641 0.187,0.191 10 4 6.475,1.224 6.700,1.443 0.225,0.218 10 1 4.999,2.043 5.346,2.199 0.347,0.156 10 G52

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the acceleration sensor, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC U0124 is output together with DTC C1243 and/or C1245, inspect and repair the trouble areas indicated by DTC U0124 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>U0073).


PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel and decelerate (depress the brake pedal) the vehicle.


d.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC output (relating to acceleration sensor) A
DTC output (relating to CAN communication system) for LHD without Entry and Start System B
DTC output (relating to CAN communication system) for RHD without Entry and Start System C



A

2.CHECK ACCELERATION SENSOR

B

C

2.CHECK ACCELERATION SENSOR
a.

Turn the ignition switch off.


b.

Check that the acceleration sensor is installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.




OK

3.CHECK TERMINAL VOLTAGE (IG, GND)

NG

3.CHECK TERMINAL VOLTAGE (IG, GND)
a.

Disconnect the G52 acceleration sensor connector.


b.
U148294E04
1.208,1.198 0.792,1.719 true 1.781,1.208 2.448,1.74 true 0.115,0.052 0.406,0.271 0.292,0.219 10 false *a 0.594,1.729 0.948,1.906 0.354,0.177 10 false GND 2.417,1.75 2.656,1.927 0.24,0.177 10 false IG 0.323,0.844 0.635,1.01 0.313,0.167 10 false G52

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G52-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G52-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Acceleration Sensor)

Result
Result Proceed to
OK (When troubleshooting in accordance with diagnostic trouble code chart) A
OK (When troubleshooting in accordance with problem symptoms table) B
NG C


A

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPAIR OR REPLACE HARNESS OR CONNECTOR