Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1403  Rear Speed Sensor RH Malfunction  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1401).

DTC Code DTC Detection Condition Trouble Area
C1403
C1404
One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that from the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of less than 10 km/h (6 mph), the outputs from both rear speed sensors are 0 km/h (0 mph) for a cumulative time of 200 seconds.


·

Rear speed sensor RH/LH

·

Rear speed sensor rotor RH/LH

·

Sensor installation


C1273
C1274
Detect only during test mode.
·

Rear speed sensor RH/LH

·

Rear speed sensor rotor RH/LH

·

Sensor installation



HINT:
·

DTC C1403 is for the rear speed sensor RH.

·

DTC C1404 is for the rear speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.
C144929E49
0.628,2.889 0.910,3.090 0.282,0.201 10 *b 2.658,2.889 2.985,3.090 0.326,0.201 10 *c 1.119,2.636 2.037,2.837 0.918,0.201 10 *a 0.114,0.065 0.349,0.263 0.235,0.198 10 *1 0.708,2.449 0.965,2.759 false 0.965,2.759 1.08,2.759 false

Check the speed sensor installation (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION).

Text in Illustration
*1 Rear Speed Sensor
*a No clearance
*b OK
*c NG

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation nut is tightened properly.




OK

2.CHECK REAR SPEED SENSOR TIP

NG

2.CHECK REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.




OK

3.CHECK REAR SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.CHECK REAR SPEED SENSOR ROTOR
a.

Remove the rear axle hub and bearing assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL).


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.




OK

4.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SPEED SENSOR ROTOR

4.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Changes continuously during acceleration/deceleration.
RL Wheel Speed Rear speed sensor LH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Changes continuously during acceleration/deceleration.


f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).




OK

NG

5.REPLACE REAR SPEED SENSOR
5.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.




NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.




A

END

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY