Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1401).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1407
C1408 |
Either condition is met:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Rear speed sensor RH/LH ·
Rear skid control sensor wire ·
Speed sensor circuit ·
Brake actuator assembly (Skid control ECU) |
DTC C1407 is for the rear speed sensor RH.
DTC C1408 is for the rear speed sensor LH.
When replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open circuit detection/ Error or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open circuit detection/ Error or Normal | Normal | - |
Normal (there are no momentary interruptions).
Perform the above inspection before removing the sensor and disconnecting the connector.
OK
NG
OK
NG
Turn the ignition switch off.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
| *A | for RH | *B | for LH |
| *1 | Skid Control Sensor Wire | - | - |
Make sure that there is no looseness at the locking parts and connecting parts of the connectors.
Remove the skid control sensor wire (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Sq1-4 - q1-2 (RR+) | Always | Below 1 Ω |
| Sq1-3 - q1-1 (RR-) | Always | Below 1 Ω |
| Sq1-4 - Sq1-3 | Always | 10 kΩ or higher |
| Sq1-4 - Sq1-1 | Always | 10 kΩ or higher |
| Sq1-4 - Sq1-2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Sq1-2 - q2-2 (RL+) | Always | Below 1 Ω |
| Sq1-1 - q2-1 (RL-) | Always | Below 1 Ω |
| Sq1-2 - Sq1-1 | Always | 10 kΩ or higher |
| Sq1-2 - Sq1-3 | Always | 10 kΩ or higher |
| Sq1-2 - Sq1-4 | Always | 10 kΩ or higher |
OK
NG
Install the skid control sensor wire.
Disconnect the A6 skid control ECU connector.
Disconnect the q1 and/or q2 speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-17 (RR+) - q1-2 (RR+) | Always | Below 1 Ω |
| A6-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A6-16 (RR-) - q1-1 (RR-) | Always | Below 1 Ω |
| A6-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-5 (RL+) - q2-2 (RL+) | Always | Below 1 Ω |
| A6-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| A6-4 (RL-) - q2-1 (RL-) | Always | Below 1 Ω |
| A6-4 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the A6 skid control ECU connector.
Disconnect the q1 and/or q2 speed sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| q1-2 (RR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| q2-2 (RL+) - Body ground | Ignition switch ON | 8 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
OK
NG