Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1429  Open or Short in Brake Pedal Load Sensing Switch  


DESCRIPTION

The brake pedal load sensing switch operates when the brake pedal is depressed with force exceeding a predetermined level.

The skid control ECU detects if the brake pedal is depressed or not via this circuit.

DTC Code DTC Detection Condition Trouble Area
C1429 An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.
·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Brake actuator assembly (Skid control ECU)



WIRING DIAGRAM

C194456E03
2.212,1.28 2.372,1.482 0.161,0.202 10 1 4.112,1.28 4.273,1.482 0.161,0.202 10 2 5.565,1.28 5.795,1.482 0.230,0.202 10 27 5.808,1.387 6.288,1.557 0.480,0.170 10 FSW+ 2.286,2.293 4.498,2.477 2.211,0.184 10 Brake Pedal Load Sensing Switch 5.416,3.043 7.004,3.369 1.587,0.326 10 Brake Actuator Assembly (Skid Control ECU) 3.623,1.154 4.103,1.323 0.480,0.170 10 FSW+ 2.378,1.154 2.858,1.323 0.480,0.170 10 FSW- 5.416,2.878 5.764,3.048 0.348,0.170 10 A6 2.291,2.125 2.639,2.295 0.348,0.170 10 A11

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


HINT:

When DTC C1425 is output together with DTC C1429, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1425).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL LOAD SENSING SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Pedal Load Sensing SW Brake pedal load sensing switch/ ON or OFF ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-


f.

Check that the brake pedal load sensing switch display observed on the intelligent tester changes according to the brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.




OK

2.RECONFIRM DTC

NG

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
2.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Perform a road and braking test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
C214171E01
1.333,2.933 1.666,3.208 0.333,0.276 10 *a 0.3,0.824 0.516,0.999 0.216,0.174 10 *b 0.3,2.426 0.508,2.614 0.208,0.188 10 *c 1.369,1.787 0.585,0.889 0.585,0.889 0.501,0.889 false 1.36,1.855 0.524,2.51 0.524,2.51 0.459,2.51 false 5.381,1.025 5.571,1.216 0.191,0.191 10 *1 4.619,4.456 4.805,4.642 0.186,0.186 10 *2 5.339,3.995 4.881,4.537 4.881,4.537 4.799,4.537 false 5.556,1.1 5.694,1.1 5.694,1.1 6.096,1.397 false 1.297,4.406 1.731,4.562 0.434,0.156 10 FSW+ 2.684,3.769 3.111,3.931 0.427,0.163 10 FSW- 1.904,3.896 1.472,4.238 1.472,4.238 1.472,4.35 false 2.618,3.855 2.179,3.855 false 0.53,1.53 0.766,1.766 0.236,0.236 10 2 2.474,1.555 2.734,1.739 0.260,0.184 10 1

Text in Illustration
*1 Brake Pedal Load Sensing Switch *2 Brake with Switch Pedal Sub-assembly
*a Component without harness connected
(Brake Pedal Load Sensing Switch)
*b Brake Pedal Released (On)
*c Brake Pedal Depressed (Off) - -

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.



a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connector.


c.

Disconnect the A11 brake pedal load sensing switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW+) - 1 (FSW-) Brake pedal depressed 0.9 to 1.1 kΩ
Brake pedal released 192 to 234 Ω




OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
a.

Make sure that there is no looseness in the locking part and connecting part of the connector.


b.

Disconnect the A6 skid control ECU connector.


c.

Disconnect the A11 brake pedal load sensing switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-27 (FSW+) - A11-2 (FSW+) Always Below 1 Ω
A6-27 (FSW+) - Body ground Always 10 kΩ or higher
A11-1 (FSW-) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR