Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  Brake Warning Light Remains ON  


DESCRIPTION

The brake warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM

C216820E01
0.476,4.548 1.709,4.745 1.232,0.198 10 Combination Meter 0.764,5.164 2.704,5.348 1.941,0.184 10 : CAN Communication System 0.914,3.584 1.327,3.761 0.413,0.177 10 Brake 1.205,2.446 1.414,2.630 0.209,0.184 10 IG 2.956,2.859 4.673,3.210 1.717,0.350 10 Main Body ECU (Multiplex Network Body ECU) 3.033,4.309 4.467,4.500 1.434,0.191 10 Parking Brake Switch 5.416,4.447 7.050,4.793 1.634,0.345 10 Master Cylinder Solenoid (Skid Control ECU) 2.956,2.684 3.237,2.861 0.281,0.177 10 A 2.914,2.089 3.126,2.265 0.211,0.177 10 12 3.187,2.187 3.563,2.336 0.376,0.149 10 PKB 3.026,4.162 3.396,4.346 0.369,0.184 10 G77 3.257,3.819 3.445,4.034 0.187,0.215 10 1 5.416,4.295 5.655,4.493 0.239,0.198 10 A7 0.476,4.386 0.733,4.570 0.257,0.184 10 G6

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

1.CHECK DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK CAN COMMUNICATION LINE

B

3.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch/ ON or OFF ON: Parking brake applied
OFF: Parking brake released
-


f.

Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.

OK:

When the parking brake is operated, the display changes as shown above.




OK

4.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)

NG

5.INSPECT PARKING BRAKE SWITCH
4.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light/ ON or OFF ON: Warning light on
OFF: Warning light off
-


f.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C

5.INSPECT PARKING BRAKE SWITCH
a.

Disconnect the G77 parking brake switch connector.


b.
C215408E01
0.223,0.014 0.560,0.229 0.336,0.215 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Parking brake applied
(Switch pin not pushed in)
Below 1 Ω
Parking brake released
(Switch pin pushed in)
10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Brake Switch)



OK

6.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU)
a.

Disconnect the G77 parking brake switch connector.


b.

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G77-1 - A-12 (PKB) Always Below 1 Ω
G77-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR