Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  C1456  Control Pressure Sensor Zero Point High  


DESCRIPTION

Refer to DTCs C1421, C1423, C1424, C1455, C1457 and C1458 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C1281).

DTC Code DTC Detection Condition Trouble Area
C1422 When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder solenoid (Master cylinder pressure sensor)


C1456 When the stop light switch is off, the PCTRL terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Pressure control sensor circuit

·

Master cylinder solenoid (Pressure control sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1422 and/or C1456, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C1425).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

OK

2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

NG

4.CHECK TERMINAL VOLTAGE AND RESISTANCE (STOP LIGHT SWITCH ASSEMBLY POWER SOURCE TERMINAL)
2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Hydraulic Brake Booster)>ADJUSTMENT).

OK:

The brake pedal height and stop light switch assembly installation are normal.




OK

3.RECONFIRM DTC

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

3.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

4.CHECK TERMINAL VOLTAGE AND RESISTANCE (STOP LIGHT SWITCH ASSEMBLY POWER SOURCE TERMINAL)
a.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


b.

Disconnect the A85 stop light switch assembly connector.


c.
U147926E01
1.621,0.213 1.914,0.386 0.292,0.173 10 A85 0.049,0.04 0.269,0.194 0.221,0.154 10 *a 0.413,1.361 0.570,1.507 0.157,0.145 10 B 1.217,1.445 0.565,1.445 false 2.747,0.869 3.094,1.060 0.347,0.191 10 GND 1.703,1.303 2.533,0.95 2.533,0.95 2.7,0.95 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-1(B) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

5.CHECK TERMINAL VOLTAGE (STP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (STP)

A

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - MASTER CYLINDER SOLENOID)

B

C

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - MASTER CYLINDER SOLENOID)
a.

Disconnect the A85 stop light switch assembly connector.


b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-2 (L) - A7-7 (STP) Always Below 1 Ω
A85-2 (L) or A7-7 (STP) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR