Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  TRC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter via the CAN communication system. Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If traction control turns off, the TRC OFF indicator light comes on.

When the temperature inside the hydraulic brake booster becomes too high, the TRC OFF indicator light turns on and traction control is stopped until the temperature decreases.

·

When the transfer is in L4, VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on.

·

w/ Rear Differential Lock:

When the rear differential lock is in the locked state, VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on. At this time, ABS is also prohibited and the ABS warning light turns on.


WIRING DIAGRAM

C215188E07
3.469,1.677 3.792,1.938 0.323,0.26 10 false G9 3.49,1.844 4.771,2.073 1.281,0.229 10 false VSC OFF Switch 4.583,1.208 4.844,1.458 0.26,0.25 10 false 6 3.354,1.198 3.698,1.458 0.344,0.26 10 false 3 5.51,1.229 5.802,1.49 0.292,0.26 10 false 9 5.813,1.333 6.292,1.552 0.479,0.219 10 false CSW 0.833,2.49 1.51,2.823 0.677,0.333 10 false TRC OFF 0.198,3.094 0.49,3.302 0.292,0.208 10 false G6 0.198,3.26 1.354,3.625 1.156,0.365 10 false Combination Meter Assembly 3.417,3.802 3.781,4.01 0.365,0.208 10 false E2 3.406,3.99 4.969,4.708 1.563,0.719 10 false Rear Differential Lock Detection Switch (Differential Lock Indicator Switch)* 2.729,2.917 3.219,3.156 0.49,0.24 10 false RLP 5.51,4.156 5.802,4.385 0.292,0.229 10 false A7 5.49,4.344 7.104,4.917 1.615,0.573 10 false Skid Control ECU (Master Cylinder Solenoid) 3.938,3.646 4.313,3.885 0.375,0.24 10 false +B 4.635,3.646 5.188,3.927 0.552,0.281 10 false GND 3.708,3.375 4.104,3.635 0.396,0.26 10 false 2 5.042,3.396 5.344,3.656 0.302,0.26 10 false 1 5.802,3.063 6.271,3.323 0.469,0.26 10 false EXI3 5.469,2.917 5.802,3.188 0.333,0.271 10 false 40 3.104,2.917 3.469,3.167 0.365,0.25 10 false 15 2.281,2.281 2.74,2.542 0.458,0.26 10 false IG 1.229,1.354 1.573,1.594 0.344,0.24 10 false IG 3.333,3.177 3.625,3.406 0.292,0.229 10 false * 2.104,3.406 2.5,3.708 0.396,0.302 10 false G53 2.115,3.594 2.979,4.052 0.865,0.458 10 false 4 Wheel Drive Control ECU 1.021,4.75 2.958,4.938 1.938,0.188 10 false : CAN Communication System 0.438,5.146 2.792,5.344 2.354,0.198 10 false *: w/ Rear Differential Lock

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).

·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>INSPECTION).



PROCEDURE

1.CHECK CAN COMMUNICATION LINE

A

2.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID CSW CIRCUIT)

B

C

2.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID CSW CIRCUIT)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A7-9 (CSW) - Body ground VSC OFF switch not pushed in 10 kΩ or higher
VSC OFF switch pushed in Below 1 Ω




OK

3.CHECK TERMINAL VOLTAGE (EXI3)

NG

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - VSC OFF SWITCH)
3.CHECK TERMINAL VOLTAGE (EXI3)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.
U148400E01
0.097,0.113 0.359,0.266 0.262,0.153 10 *a 2.624,0.422 2.972,0.594 0.348,0.172 10 EXI3 2.595,0.505 2.522,0.505 2.522,0.505 2.02,1.502 false 0.207,0.741 0.432,0.911 0.225,0.170 10 A7

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-40 (EXI3) - Body ground Ignition switch ON
w/ Rear Differential Lock: Rear differential free
11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

4.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

NG

7.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID EXI3 CIRCUIT)
4.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode/ Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC OFF mode
VSC OFF: VSC OFF mode
-


f.

Check that the mode display changes according to VSC OFF switch operation.

OK:

Display changes according to switch operation.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - VSC OFF SWITCH)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the G9 VSC OFF switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-9 (CSW) - G9-6 Always Below 1 Ω
A7-9 (CSW) - Body ground Always 10 kΩ or higher
G9-3 - Body ground Always Below 1 Ω




OK

6.INSPECT VSC OFF SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT VSC OFF SWITCH

b.
C215409E02
0.221,0.063 0.520,0.285 0.299,0.222 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 - 3 Switch is not pushed 10 kΩ or higher
Switch is pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(VSC OFF Switch)

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

B

C

7.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID EXI3 CIRCUIT)

A

8.CHECK TERMINAL VOLTAGE (EXI3)

B

9.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)

OK

10.CHECK TERMINAL VOLTAGE (EXI3)

NG

REPLACE REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)