Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › 2015.06–2017.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM G

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT INDICATOR LIGHT

a.

4LO Indicator Light:

i.

Turn the ignition switch to ON.


ii.

Move the shift lever to N (vehicle is stopped).


iii.

for 1GR-FE, 1KD-FTV, 1GD-FTV:

Change the transfer position switch from H4 to L4.


iv.

for 2TR-FE, 5L-E:

Change the transfer position switch from H4L to L4L.


v.

Check the 4LO indicator light.

OK:

4LO indicator light comes on or 4LO indicator light comes on after blinking.


If the result is not as specified, inspect the switch, 4 wheel drive control ECU and transfer shift actuator assembly.

If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>PROBLEM SYMPTOMS TABLE). Then check the combination meter (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>PROBLEM SYMPTOMS TABLE).



b.

Center Differential Lock Indicator Light:

i.

Turn the ignition switch to ON.


ii.

for 1GR-FE, 1KD-FTV, 1GD-FTV:

Change the center differential lock switch from Free to Lock.


iii.

for 2TR-FE, 5L-E:

Change the transfer position switch from H4F to H4L.


iv.

Check the center differential lock indicator light.

OK:

Center differential lock indicator light comes on


If the result is not as specified, inspect the switches, 4 wheel drive control ECU, transfer and shift actuator.

If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>PROBLEM SYMPTOMS TABLE). Then check the combination meter (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>PROBLEM SYMPTOMS TABLE).



Hide 89533 2.INSPECT 4 WHEEL DRIVE CONTROL ECU (POWER SUPPLY)

a.
U148710E01
0.097,0.05 0.281,0.213 0.184,0.163 10 *a 2.34,0.268 2.649,0.424 0.309,0.156 10 G54 1.833,1.712 2.174,1.886 0.341,0.174 10 GND 1.81,0.311 2.060,0.476 0.250,0.165 10 IG 2.283,0.897 2.141,0.403 2.141,0.403 2.047,0.403 false 2.146,0.967 2.035,1.689 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-3 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(4 wheel drive control ECU)

If the result is not as specified, inspect the harness, fuse or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the 4 wheel drive control ECU (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-4 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.


Hide 89533 3.INSPECT 4 WHEEL DRIVE CONTROL ECU (TRANSFER POSITION SWITCH)

a.
U148711E01
0.097,0.05 0.281,0.213 0.184,0.163 10 *a 1.128,0.269 1.437,0.424 0.309,0.156 10 G53 1.833,1.658 2.304,1.832 0.471,0.174 10 2-4*A 0.269,1.658 0.519,1.822 0.250,0.165 10 LO 1.238,1.029 1.934,1.64 false 1.097,1.024 0.415,1.637 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1GR-FE, 1KD-FTV, 1GD-FTV:
Tester Connection Switch Condition Specified Condition
G53-13 (LO) - Body ground Ignition switch ON
Transfer position switch H4
10.5 to 14 V
Ignition switch ON
Transfer position switch L4
Below 1.5 V

for 2TR-FE, 5L-E:
Tester Connection Switch Condition Specified Condition
G53-11 (2-4) - Body ground Ignition switch ON
Transfer position switch H4F
Below 1.5 V
Ignition switch ON
Transfer position switch H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
10.5 to 14 V
G53-13 (LO) - Body ground Ignition switch ON
Transfer position switch H4F
10.5 to 14 V
Ignition switch ON
Transfer position switch H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
Below 1.5 V


Text in Illustration
*A for 2TR-FE, 5L-E
*a Component with harness connected
(4 wheel drive control ECU)

If the result is not as specified, check the power supply.

If the power supply is normal, inspect the transfer position switch (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>ON-VEHICLE INSPECTION).


Hide 89533 4.INSPECT 4 WHEEL DRIVE CONTROL ECU (CENTER DIFFERENTIAL LOCK SWITCH) (for 1GR-FE, 1KD-FTV, 1GD-FTV)

a.
U148712E01
0.097,0.062 0.281,0.225 0.184,0.163 10 *a 1.128,0.281 1.437,0.437 0.309,0.156 10 G53 0.301,1.67 0.551,1.834 0.250,0.165 10 DL 0.878,1.036 0.415,1.649 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G53-16 (DL) - Body ground Ignition switch ON
Center differential lock switch ON
Below 1.5 V
Ignition switch ON
Center differential lock switch OFF
9.5 to 14 V


Text in Illustration
*a Component with harness connected
(4 wheel drive control ECU)

If the result is not as specified, check the power supply.

If the power supply is normal, inspect the center differential lock switch (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch)>INSPECTION).


Hide 36410J 5.INSPECT MULTI MODE TRANSFER SHIFT ACTUATOR

a.

Check the harness and connector between 4 wheel drive control ECU and transfer shift actuator assembly (multi mode transfer shift actuator).

i.

Disconnect the C43 actuator connector.


ii.

Disconnect the G53 and G54 ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

U148719E01
0.506,0.079 0.690,0.292 0.184,0.213 10 *a 5.017,0.079 5.205,0.275 0.188,0.196 10 *b 1.432,0.296 1.768,0.489 0.336,0.193 10 G53 3.511,0.268 3.848,0.461 0.336,0.193 10 G54 5.6,0.184 5.936,0.377 0.336,0.193 10 C43 3.844,1.412 4.142,1.565 0.298,0.152 10 TM1 3.245,1.416 3.557,1.590 0.312,0.174 10 TM2 0.827,1.462 1.180,1.622 0.353,0.161 10 TL2 1.358,1.462 1.641,1.622 0.283,0.161 10 TL3 2.039,1.418 2.228,1.588 0.189,0.169 10 P1 3.769,1.095 3.972,1.408 false 3.534,1.11 3.402,1.39 false 5.198,1.447 5.501,1.610 0.303,0.163 10 TM1 5.594,1.447 5.902,1.598 0.308,0.151 10 CDL 4.76,1.447 5.081,1.607 0.320,0.159 10 TM2 6.521,0.413 6.787,0.552 0.265,0.139 10 TL3 6.549,0.623 7.037,0.784 0.488,0.161 10 GND1 6.38,0.189 6.647,0.358 0.266,0.169 10 TL2 1.2,0.924 0.999,1.439 false 1.34,0.94 1.47,1.439 false 1.973,0.924 2.101,1.383 false 5.246,0.899 4.909,1.397 false 5.445,0.928 5.343,1.397 false 5.662,1.103 5.711,1.425 false 6.051,0.803 6.492,0.494 false 5.858,0.795 6.334,0.273 false 6.25,0.858 6.509,0.697 false 5.984,1.447 6.472,1.608 0.488,0.161 10 GND 5.85,1.104 6.119,1.427 false

Standard Resistance:
Tester Connection Condition Specified Condition
G53-7 (TL2) - C43-4 (TL2) Always Below 1 Ω
G53-7 (TL2) - Body ground Always 10 kΩ or higher
G53-8 (TL3) - C43-5 (TL3) Always Below 1 Ω
G53-8 (TL3) - Body ground Always 10 kΩ or higher
G53-14 (P1) - C43-9 (CDL) Always Below 1 Ω
G53-14 (P1) - Body ground Always 10 kΩ or higher
G54-7 (TM2) - C43-1 (TM2) Always Below 1 Ω
G54-7 (TM2) - Body ground Always 10 kΩ or higher
G54-8 (TM1) - C43-2 (TM1) Always Below 1 Ω
G54-8 (TM1) - Body ground Always 10 kΩ or higher
C43-6 (GND1) - Body ground Always Below 1 Ω
C43-10 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to 4 wheel drive control ECU)
*b Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

If the result is not as specified, repair or replace the harness or connector.

If the harness or connector is normal, check the ECU output voltage.



b.

Check the 4 wheel drive control ECU (multi mode transfer shift actuator circuit).

i.

Connect the G53 and G54 ECU connectors.


ii.

Connect the C43 actuator connector.


iii.
U148713E03
1.438,1.073 0.813,1.688 false 1.01,1.073 0.344,1.688 false 1.521,1.083 1.656,1.688 false 2.448,1.177 2.781,1.635 false 2.177,1.021 2.198,1.635 false 2.604,1.156 3.25,1.667 false 0.094,0.094 0.281,0.26 0.188,0.167 10 false *a 1.135,0.313 1.448,0.469 0.313,0.156 10 false G53 2.292,0.313 2.604,0.469 0.313,0.156 10 false G54 1.51,1.708 1.781,1.854 0.271,0.146 10 false TL2 2.021,1.708 2.365,1.854 0.344,0.146 10 false GND 2.635,1.708 2.958,1.854 0.323,0.146 10 false TM1 3.063,1.708 3.375,1.854 0.313,0.146 10 false TM2 0.198,1.708 0.406,1.875 0.208,0.167 10 false P1 0.615,1.708 0.885,1.875 0.271,0.167 10 false TL3

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1GR-FE, 1KD-FTV, 1GD-FTV:
Tester Connection Switch Condition Specified Condition
G54-8 (TM1) - G54-4 (GND) Ignition switch ON
Center differential lock switch FREE → LOCK (During operation of multi mode transfer shift actuator motor from FREE to LOCK)
10 to 14 V
Ignition switch ON
Center differential lock switch FREE → LOCK (Multi mode transfer shift actuator motor stopped)
Below 1.5 V
G54-7 (TM2) - G54-4 (GND) Ignition switch ON
Center differential lock switch LOCK → FREE (During operation of multi mode transfer shift actuator motor from LOCK to FREE)
10 to 14 V
Ignition switch ON
Center differential lock switch LOCK → FREE (Multi mode transfer shift actuator motor stopped)
Below 1.5 V
G53-7 (TL2) - G54-4 (GND) Ignition switch ON
Center differential lock switch LOCK
Below 1.5 V
Ignition switch ON
Center differential lock switch FREE
10.5 to 14 V
G53-8 (TL3) - G54-4 (GND) Ignition switch ON
Center differential lock switch LOCK
10.5 to 14 V
Ignition switch ON
Center differential lock switch FREE
Below 1.5 V
G53-14 (P1) - G54-4 (GND) Ignition switch ON
Center differential lock switch FREE
9.5 to 14 V
Ignition switch ON
Center differential lock switch LOCK
Below 1.5 V

for 2TR-FE, 5L-E:
Tester Connection Switch Condition Specified Condition
G54-8 (TM1) - G54-4 (GND) Ignition switch ON
Transfer position switch H4F → H4L (During operation of multi mode transfer shift actuator motor from FREE to LOCK)
10 to 14 V
Ignition switch ON
Transfer position switch H4F → H4L (Multi mode transfer shift actuator motor stopped)
Below 1.5 V
G54-7 (TM2) - G54-4 (GND) Ignition switch ON
Transfer position switch H4L → H4F (During operation of multi mode transfer shift actuator motor from LOCK to FREE)
10 to 14 V
Ignition switch ON
Transfer position switch H4L → H4F (Multi mode transfer shift actuator motor stopped)
Below 1.5 V
G53-7 (TL2) - G54-4 (GND) Ignition switch ON
Transfer position switch H4L or L4L
Below 1.5 V
Ignition switch ON
Transfer position switch H4F
10.5 to 14 V
G53-8 (TL3) - G54-4 (GND) Ignition switch ON
Transfer position switch H4L or L4L
10.5 to 14 V
Ignition switch ON
Transfer position switch H4F
Below 1.5 V
G53-14 (P1) - G54-4 (GND) Ignition switch ON
Transfer position switch H4F
9.5 to 14 V
Ignition switch ON
Transfer position switch H4L or L4L
Below 1.5 V


Text in Illustration
*a Component with harness connected
(4 wheel drive control ECU)

If the result is not as specified, determine if a malfunction is on the ECU side or actuator side by disconnecting the connector of the transfer shift actuator, and then check the ECU output voltage.



c.

Check the 4 wheel drive control ECU output voltage.

i.

Disconnect the C43 actuator connector.


ii.

Connect the G53 and G54 ECU connectors.


iii.
U148720E01
0.092,0 0.300,0.170 0.208,0.170 10 *a 0.318,0.434 0.599,0.583 0.281,0.149 10 C43 2.005,1.611 2.312,1.794 0.306,0.183 10 TL2 2.464,0.222 2.786,0.405 0.322,0.183 10 TL3 2.683,0.641 3.176,0.792 0.493,0.150 10 GND1 1.494,1.611 1.828,1.779 0.334,0.167 10 CDL 1.544,1.196 1.661,1.571 false 1.806,0.954 2.148,1.567 false 2.034,0.838 2.416,0.323 false 2.266,0.937 2.627,0.735 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C43-9 (CDL) - C43-6 (GND1) Ignition switch ON 9.5 to 14 V
C43-4 (TL2) - C43-6 (GND1) Ignition switch ON 10.5 to 14 V
C43-5 (TL3) - C43-6 (GND1) Ignition switch ON 10.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

If the result is not as specified, replace the 4 wheel drive control ECU (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).

If the voltage is normal, inspect the multi mode transfer shift actuator, because the voltage applied to the motor cannot be measured.



d.

Inspect the multi mode transfer shift actuator (transfer shift actuator assembly).

i.

Remove the transfer shift actuator assembly (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>DISASSEMBLY).


ii.

Check the LOCK to FREE switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the LOCK to FREE position.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEF relay on the main body ECU (instrument panel junction block).


C218269E04
4.77,0.288 4.980,0.436 0.210,0.148 10 *1 2.547,1.037 2.757,1.185 0.210,0.148 10 *1 5.237,0.826 5.422,1.008 0.185,0.181 10 1 6.577,0.826 6.741,1.019 0.164,0.193 10 2 6.075,0.826 6.323,0.992 0.248,0.165 10 4 6.653,1.906 6.819,2.097 0.166,0.191 10 5 6.653,2.553 6.820,2.713 0.167,0.161 10 3 0.519,2.343 0.702,2.502 0.183,0.160 10 *a 1.994,3.398 2.366,3.558 0.373,0.159 10 TM1 2.155,2.75 2.498,2.920 0.343,0.170 10 TM2 0.428,3.409 0.737,3.579 0.309,0.170 10 TL3 0.175,2.756 0.595,2.919 0.420,0.163 10 GND1 1.168,3.375 1.535,3.538 0.368,0.163 10 GND 0.706,1.078 1.020,1.262 0.314,0.184 10 *b 0.795,3.409 1.128,3.586 0.333,0.177 10 TL2 6.05,1.995 6.604,1.995 false 6.05,2.407 6.604,2.624 false 6.096,1.414 6.535,0.886 false 5.835,1.414 6.027,0.895 false 5.582,1.414 5.368,0.886 false 6.05,1.995 6.604,1.995 false 6.05,2.407 6.604,2.624 false 6.096,1.414 6.535,0.886 false 5.835,1.414 6.027,0.895 false 5.582,1.414 5.368,0.886 false 2.108,2.823 1.765,2.823 false 2.066,3.377 1.561,2.874 false 1.573,3.374 1.906,3.551 0.333,0.177 10 CDL 0.983,3.379 1.239,2.878 false 0.594,3.385 1.081,2.883 false 0.875,2.826 0.566,2.826 false 1.454,3.006 1.675,3.355 false 1.266,3.037 1.323,3.362 false

1.

After the LOCK to FREE switch is complete, inspect the center differential lock detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (TL2) - 6 (GND1) After LOCK to FREE switch is complete 0.5 MΩ or higher
5 (TL3) - 6 (GND1) After LOCK to FREE switch is complete Below 12.5 Ω
9 (CDL) - 10 (GND) After LOCK to FREE switch is complete 0.5 MΩ or higher


Text in Illustration
*1 DEF Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b LOCK to FREE



iii.

Check the FREE to LOCK switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the FREE to LOCK position.

C218270E03
5.049,0.351 5.240,0.553 0.192,0.202 10 *1 2.592,1.032 2.784,1.235 0.192,0.202 10 *1 5.241,0.824 5.425,1.005 0.185,0.181 10 1 6.58,0.824 6.744,1.017 0.164,0.193 10 2 6.078,0.824 6.327,0.989 0.248,0.165 10 4 6.656,1.903 6.822,2.094 0.166,0.191 10 5 6.656,2.55 6.823,2.711 0.167,0.161 10 3 0.457,2.144 0.638,2.343 0.181,0.199 10 *a 1.948,3.41 2.320,3.569 0.373,0.159 10 TM1 2.151,2.755 2.494,2.925 0.343,0.170 10 TM2 0.302,3.423 0.610,3.593 0.309,0.170 10 TL3 0.159,2.754 0.602,2.917 0.443,0.163 10 GND1 1.163,3.38 1.509,3.542 0.346,0.163 10 GND 0.849,0.983 1.139,1.166 0.290,0.184 10 *b 0.711,3.425 1.044,3.602 0.333,0.177 10 TL2 6.053,1.992 6.607,1.992 false 6.053,2.404 6.607,2.621 false 6.099,1.412 6.538,0.883 false 5.838,1.412 6.03,0.892 false 5.586,1.412 5.371,0.883 false 2.111,2.82 1.768,2.82 false 2.069,3.375 1.564,2.871 false 1.576,3.428 1.909,3.605 0.333,0.177 10 CDL 0.969,3.334 1.262,2.876 false 0.74,3.289 1.098,2.88 false 0.905,2.829 0.562,2.829 false 1.466,3.028 1.655,3.387 false 1.266,3.047 1.31,3.35 false

1.

After the FREE to LOCK switch is complete, inspect the center differential lock detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (TL2) - 6 (GND1) After FREE to LOCK switch is complete Below 12.5 Ω
5 (TL3) - 6 (GND1) After FREE to LOCK switch is complete 0.5 MΩ or higher
9 (CDL) - 10 (GND) After FREE to LOCK switch is complete Below 12.5 Ω


Text in Illustration
*1 DEF Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b FREE to LOCK

If the result is not as specified, replace the transfer shift actuator assembly (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>DISASSEMBLY). If the transfer shift actuator assembly is normal, replace the 4 wheel drive control ECU (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).




Hide 36410J 6.INSPECT HIGH-LOW TRANSFER SHIFT ACTUATOR

a.

Check the harness and connector between 4 wheel drive control ECU and transfer shift actuator (high-low transfer shift actuator).

i.

Disconnect the C43 actuator connector.


ii.

Disconnect the G53 and G54 ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

U148718E01
0.506,0.079 0.690,0.292 0.184,0.213 10 *a 5.017,0.079 5.205,0.275 0.188,0.196 10 *b 1.463,0.296 1.800,0.489 0.336,0.193 10 G53 3.517,0.268 3.853,0.461 0.336,0.193 10 G54 5.62,0.184 5.956,0.377 0.336,0.193 10 C43 3.245,1.416 3.557,1.590 0.312,0.174 10 HM2 3.914,1.416 4.226,1.590 0.312,0.174 10 HM1 0.203,1.462 0.556,1.622 0.353,0.161 10 HL1 0.751,1.462 1.034,1.622 0.283,0.161 10 HL2 3.448,0.897 4.057,1.39 false 5.198,1.425 5.529,1.588 0.331,0.163 10 HM1 4.76,1.425 5.081,1.585 0.320,0.159 10 HM2 6.6,0.826 6.886,0.965 0.286,0.139 10 HL1 5.744,1.422 6.079,1.582 0.335,0.161 10 GND 6.564,1.319 6.872,1.488 0.308,0.169 10 HL2 0.577,0.924 0.375,1.439 false 0.728,0.93 0.863,1.439 false 5.256,1.083 4.909,1.397 false 5.48,1.096 5.343,1.397 false 5.844,1.103 5.893,1.425 false 6.25,0.979 6.57,0.907 false 6.019,1.098 6.518,1.382 false 3.402,1.116 3.402,1.387 false

Standard Resistance:
Tester Connection Condition Specified Condition
G53-1 (HL1) - C43-12 (HL1) Always Below 1 Ω
G53-1 (HL1) - Body ground Always 10 kΩ or higher
G53-2 (HL2) - C43-11 (HL2) Always Below 1 Ω
G53-2 (HL2) - Body ground Always 10 kΩ or higher
G54-2 (HM1) - C43-8 (HM1) Always Below 1 Ω
G54-2 (HM1) - Body ground Always 10 kΩ or higher
G54-6 (HM2) - C43-7 (HM2) Always Below 1 Ω
G54-6 (HM2) - Body ground Always 10 kΩ or higher
C43-10 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to 4 wheel drive control ECU)
*b Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

If the result is not as specified, repair or replace the harness or connector.

If the harness or connector is normal, check the ECU output voltage.



b.

Check the 4 wheel drive control ECU (high-low transfer shift actuator circuit).

i.

Connect the G53 and G54 ECU connectors.


ii.

Connect the C43 actuator connector.


iii.
U148714E01
0.097,0.079 0.281,0.242 0.184,0.163 10 *a 1.13,0.298 1.439,0.453 0.309,0.156 10 G53 2.292,0.298 2.600,0.453 0.309,0.156 10 G54 1.792,1.906 2.091,2.057 0.299,0.151 10 HL1 2.017,1.687 2.361,1.837 0.344,0.151 10 GND 2.824,1.687 3.146,1.837 0.321,0.151 10 HM2 3.082,0.42 3.399,0.571 0.316,0.151 10 HM1 1.504,1.69 1.789,1.854 0.286,0.165 10 HL2 1.875,1.046 1.694,1.672 false 1.966,1.06 1.935,1.891 false 2.717,1.163 2.971,1.621 false 2.197,1.006 2.197,1.618 false 2.735,0.924 3.042,0.517 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1GR-FE, 1KD-FTV, 1GD-FTV:
Tester Connection Switch Condition Specified Condition
G54-6 (HM2) - G54-4 (GND) Ignition switch ON
Transfer position switch L4 → H4 (During operation of high-low transfer shift actuator motor from LOW to HIGH)
10 to 14 V
Ignition switch ON
Transfer position switch L4 → H4 (High-low transfer shift actuator motor stopped)
Below 1.5 V
G54-2 (HM1) - G54-4 (GND) Ignition switch ON
Transfer position switch H4 → L4 (During operation of high-low transfer shift actuator motor from HIGH to LOW)
10 to 14 V
Ignition switch ON
Transfer position switch H4 → L4 (High-low transfer shift actuator motor stopped)
Below 1.5 V
G53-1 (HL1) - G54-4 (GND) Ignition switch ON
Transfer position switch H4
10.5 to 14 V
Ignition switch ON
Transfer position switch L4
Below 1.5 V
G53-2 (HL2) - G54-4 (GND) Ignition switch ON
Transfer position switch H4
Below 1.5 V
Ignition switch ON
Transfer position switch L4
10.5 to 14 V

for 2TR-FE, 5L-E:
Tester Connection Switch Condition Specified Condition
G54-6 (HM2) - G54-4 (GND) Ignition switch ON
Transfer position switch L4L → H4L (During operation of high-low transfer shift actuator motor from LOW to HIGH)
10 to 14 V
Ignition switch ON
Transfer position switch L4L → H4L (High-low transfer shift actuator motor stopped)
Below 1.5 V
G54-2 (HM1) - G54-4 (GND) Ignition switch ON
Transfer position switch H4L → L4L (During operation of high-low transfer shift actuator motor from HIGH to LOW)
10 to 14 V
Ignition switch ON
Transfer position switch H4L → L4L (High-low transfer shift actuator motor stopped)
Below 1.5 V
G53-1 (HL1) - G54-4 (GND) Ignition switch ON
Transfer position switch H4F or H4L
10.5 to 14 V
Ignition switch ON
Transfer position switch L4L
Below 1.5 V
G53-2 (HL2) - G54-4 (GND) Ignition switch ON
Transfer position switch H4F or H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
10.5 to 14 V


Text in Illustration
*a Component with harness connected
(4 wheel drive control ECU)

If the result is not as specified, determine if the malfunction is on the ECU side or actuator side by disconnecting the connector of the transfer shift actuator, and then check the ECU output voltage.



c.

Check the 4 wheel drive control ECU output voltage.

i.

Connect the G53 and G54 ECU connectors.


ii.

Disconnect the C43 actuator connector.


iii.
U148721E01
0.092,0 0.300,0.170 0.208,0.170 10 *a 0.306,0.434 0.587,0.583 0.281,0.149 10 C43 2.444,1.746 2.750,1.929 0.306,0.183 10 HL2 2.717,1.18 3.039,1.363 0.322,0.183 10 HL1 1.717,1.746 2.052,1.913 0.334,0.167 10 GND 1.759,1.196 1.905,1.709 false 1.982,1.174 2.587,1.721 false 2.264,1.141 2.674,1.247 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C43-11 (HL2) - C43-10 (GND) Ignition switch ON 10.5 to 14 V
C43-12 (HL1) - C43-10 (GND) Ignition switch ON 10.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

If the result is not as specified, replace the 4 wheel drive control ECU (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).

If the voltage is normal, inspect the high-low transfer shift actuator, because the voltage applied to the motor cannot be measured.



d.

Inspect the high-low transfer shift actuator (transfer shift actuator assembly).

i.

Remove the transfer shift actuator assembly (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>DISASSEMBLY).


ii.

Check the HIGH to LOW switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the HIGH to LOW position.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEF relay on the main body ECU (instrument panel junction block).


C218271E02
4.679,0.558 4.855,0.722 0.176,0.164 10 *1 2.676,1.492 2.852,1.656 0.176,0.164 10 *1 5.165,1.198 5.349,1.379 0.185,0.181 10 1 6.504,1.198 6.668,1.391 0.164,0.193 10 2 6.002,1.198 6.251,1.363 0.248,0.165 10 4 6.58,2.277 6.746,2.468 0.166,0.191 10 5 6.58,2.924 6.747,3.084 0.167,0.161 10 3 0.342,1.226 0.539,1.390 0.197,0.164 10 *a 1.702,1.493 2.075,1.653 0.373,0.159 10 HM1 1.999,1.727 2.342,1.897 0.343,0.170 10 HM2 0.191,2.2 0.500,2.370 0.309,0.170 10 HL1 0.609,1.456 0.987,1.619 0.378,0.163 10 GND 0.642,0.953 0.840,1.106 0.198,0.153 10 *b 0.237,1.699 0.570,1.876 0.333,0.177 10 HL2 5.978,2.366 6.532,2.366 false 5.978,2.778 6.532,2.995 false 6.024,1.785 6.462,1.257 false 5.762,1.785 5.955,1.266 false 5.51,1.785 5.295,1.257 false 0.83,2.269 0.487,2.269 false 1.06,2.214 0.544,1.773 false 1.229,2.207 0.963,1.528 false 1.542,2.2 1.647,1.57 false 1.73,2.223 1.954,1.803 false

1.

After the HIGH to LOW switch is complete, inspect the limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (HL1) - 10 (GND) After HIGH to LOW switch is complete Below 12.5 Ω
11 (HL2) - 10 (GND) After HIGH to LOW switch is complete 0.5 MΩ or higher


Text in Illustration
*1 DEF Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b HIGH to LOW



iii.

Check the LOW to HIGH switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the LOW to HIGH position.

C218272E02
4.906,0.555 5.071,0.757 0.164,0.202 10 *1 2.618,1.526 2.782,1.728 0.164,0.202 10 *1 5.161,1.194 5.346,1.376 0.185,0.181 10 1 6.501,1.194 6.665,1.387 0.164,0.193 10 2 5.999,1.194 6.247,1.359 0.248,0.165 10 4 6.577,2.274 6.742,2.465 0.166,0.191 10 5 6.577,2.921 6.743,3.081 0.167,0.161 10 3 0.326,1.171 0.530,1.331 0.205,0.161 10 *a 2.007,1.7 2.380,1.860 0.373,0.159 10 HM2 1.726,1.481 2.069,1.650 0.343,0.170 10 HM1 0.255,2.194 0.564,2.364 0.309,0.170 10 HL1 0.638,1.462 1.016,1.625 0.378,0.163 10 GND 0.947,0.918 1.165,1.080 0.218,0.162 10 *b 0.246,1.702 0.579,1.879 0.333,0.177 10 HL2 5.974,2.363 6.528,2.363 false 5.974,2.775 6.528,2.992 false 6.02,1.782 6.459,1.254 false 5.758,1.782 5.951,1.263 false 5.506,1.782 5.291,1.254 false 0.878,2.26 0.535,2.26 false 1.057,2.211 0.54,1.77 false 1.259,2.204 0.993,1.524 false 1.568,2.197 1.673,1.566 false 1.736,2.204 1.96,1.784 false

1.

After the LOW to HIGH switch is complete, inspect the limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (HL1) - 10 (GND) After LOW to HIGH switch is complete 0.5 MΩ or higher
11 (HL2) - 10 (GND) After LOW to HIGH switch is complete Below 12.5 Ω


Text in Illustration
*1 DEF Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b LOW to HIGH

If the result is not as specified, replace the transfer shift actuator assembly (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>DISASSEMBLY). If the transfer shift actuator assembly is normal, replace the 4 wheel drive control ECU (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).