Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1210  Zero Point Calibration of Yaw Rate Sensor Undone  C1336  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.

The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

The DTCs are also stored when calibration has not been completed.

DTC Code DTC Detection Condition Trouble Area
C1210 Zero point calibration of the yaw rate sensor is incomplete.
·

Yaw rate and acceleration sensor

·

Brake actuator assembly (Skid control ECU)


C1336 Zero point calibration of the acceleration sensor is incomplete.
·

Yaw rate and acceleration sensor

·

Brake actuator assembly (Skid control ECU)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly and/or yaw rate and acceleration sensor, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).


HINT:

When DTC U0123, U0124 and/or U0126 is output along with DTC C1210 and/or C1336, inspect and repair trouble areas indicated by DTC U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>U0073).


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).



NEXT

2.PERFORM TEST MODE (SIGNAL CHECK)
2.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check in the test mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>TEST MODE PROCEDURE).

OK:

All test mode DTCs are cleared.




OK

END

NG

3.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
3.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor is installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not installed at an angle.




OK

4.READ VALUE USING INTELLIGENT TESTER (YAW RATE AND ACCELERATION SENSOR)

NG

INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY

4.READ VALUE USING INTELLIGENT TESTER (YAW RATE AND ACCELERATION SENSOR)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement
Item/Range
Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor/ Min.: -18.525 m/s2, Max.: 18.387 m/s2 - Changes continuously during acceleration/deceleration.
Deceleration Sensor2 Acceleration sensor 2/ Min.: -18.525 m/s2, Max.: 18.387 m/s2 - Changes continuously during acceleration/deceleration.
Yaw Rate Sensor Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-


f.

Check the yaw rate and acceleration sensor output value displayed on the intelligent tester.

OK:

The yaw rate and acceleration sensor output value is normal.


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>TEST MODE PROCEDURE).




OK

NG