Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  TRC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter via the CAN communication system.

Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns off, the TRC OFF indicator light comes on.

WIRING DIAGRAM

C215177E01
5.255,2.035 5.543,2.256 0.288,0.221 10 A6 5.255,2.222 6.883,2.619 1.628,0.397 10 Brake Actuator Assembly (Skid Control ECU) 3.199,1.891 4.355,2.121 1.156,0.230 10 VSC OFF Switch 0.628,2.582 1.890,2.775 1.262,0.193 10 Combination Meter 0.662,3.157 2.667,3.369 2.005,0.212 10 : CAN Communication System 1.044,1.352 1.708,1.522 0.664,0.170 10 TRC OFF 1.298,1.849 1.584,2.014 0.286,0.165 10 IG 0.864,0.695 1.237,0.994 0.373,0.299 10 CPU 0.628,2.444 0.867,2.614 0.239,0.170 10 G6 3.189,1.735 3.449,1.919 0.260,0.184 10 G9 4.082,1.302 4.265,1.451 0.184,0.149 10 6 3.052,1.288 3.180,1.465 0.128,0.177 10 3 5.462,1.4 5.854,1.577 0.392,0.177 10 CSW 5.178,1.267 5.410,1.465 0.232,0.198 10 30

CAUTION / NOTICE / HINT

NOTICE:
·
·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>INSPECTION).



PROCEDURE

2.INSPECT VSC OFF SWITCH

b.
C215409E02
0.221,0.063 0.520,0.285 0.299,0.222 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 - 3 Switch is not pushed 10 kΩ or higher
Switch is pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(VSC OFF Switch)



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the G9 VSC OFF switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-30 (CSW) - G9-6 Always Below 1 Ω
A6-30 (CSW) - Body ground Always 10 kΩ or higher
G9-3 - Body ground Always Below 1 Ω




OK

4.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the Intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode/ Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC OFF mode
VSC OFF: VSC OFF mode
-


f.

Check that the mode display changes according to VSC OFF switch operation.

OK:

Display changes according to switch operation.




OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG