Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E286234E06
0.406,5.604 2.448,5.885 2.042,0.281 10 false Steering Pad Switch Assembly 0.156,6.875 2.198,7.156 2.042,0.281 10 false *1: for Manual Transmission 0.156,7.25 2.198,7.531 2.042,0.281 10 false *2: for Automatic Transmission 6.135,0.448 6.51,0.625 0.375,0.177 10 false SWG 5.719,0.438 6.052,0.615 0.333,0.177 10 false H56 5.771,0.229 6.104,0.406 0.333,0.177 10 false 23 6.135,2.99 6.51,3.167 0.375,0.177 10 false ILL+ 3.938,1.667 5.271,1.844 1.333,0.177 10 false from PANEL Fuse 5.719,3 6.052,3.177 0.333,0.177 10 false H54 5.771,2.781 6.104,2.958 0.333,0.177 10 false 10 5.031,4.969 5.365,5.146 0.333,0.177 10 false G76 5.063,4.75 5.302,4.927 0.24,0.177 10 false 4*1 3.813,4.948 4.146,5.125 0.333,0.177 10 false G40 3.885,4.74 4.125,4.917 0.24,0.177 10 false 10 3.813,3 4.146,3.177 0.333,0.177 10 false G40 3.885,2.792 4.125,2.969 0.24,0.177 10 false 12 3.813,0.438 4.146,0.615 0.333,0.177 10 false G40 3.281,0.333 3.615,0.51 0.333,0.177 10 false EAU 3.281,2.885 3.615,3.063 0.333,0.177 10 false IL+2 3.25,4.854 3.688,5.031 0.438,0.177 10 false GND1 3.927,0.24 4.167,0.417 0.24,0.177 10 false 4 2.823,4.958 3.156,5.135 0.333,0.177 10 false z8 2.865,4.74 3.104,4.917 0.24,0.177 10 false 3 2.823,3 3.156,3.177 0.333,0.177 10 false z8 2.854,2.792 3.094,2.969 0.24,0.177 10 false 5 2.813,0.438 3.146,0.615 0.333,0.177 10 false z8 2.854,0.25 3.094,0.427 0.24,0.177 10 false 8 5.396,4.948 5.771,5.125 0.375,0.177 10 false G163 5.875,4.958 6.25,5.135 0.375,0.177 10 false SWI2 5.448,4.729 5.75,4.906 0.302,0.177 10 false 14*2 5.031,5.417 5.365,5.594 0.333,0.177 10 false G76 5.01,5.219 5.323,5.396 0.313,0.177 10 false 16*1 5.396,5.427 5.771,5.604 0.375,0.177 10 false G163 5.875,5.438 6.25,5.615 0.375,0.177 10 false GND 5.479,5.198 5.719,5.375 0.24,0.177 10 false 7*2 6.135,3.542 6.594,3.719 0.458,0.177 10 false GND1 5.719,3.531 6.052,3.708 0.333,0.177 10 false H54 5.833,3.323 6.167,3.5 0.333,0.177 10 false 7 3.031,5.573 4.042,6 1.01,0.427 10 false Spiral Cable Sub-assembly 5.854,3.948 7.156,4.313 1.302,0.365 10 false Navigation Receiver Assembly 5.49,5.885 6.917,6.25 1.427,0.365 10 false Driving Support Switch Control ECU 0.448,5.198 2.365,5.469 1.917,0.271 10 false Steering Pad Switch RH Side 0.354,2.365 2.271,2.635 1.917,0.271 10 false Steering Pad Switch LH Side

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.


Result
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation receiver assembly. B
Illumination comes on for all components except steering pad switch assembly and navigation receiver assembly. C
No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.). D


A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)

B

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

7.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)

D

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)
a.
U149178E01
2.471,1.898 2.796,2.044 0.326,0.147 10 IL+2 2.098,1.702 2.264,1.986 2.264,1.986 2.448,1.986 false 0.045,0.067 2.397,0.468 2.352,0.401 10 *a 0.656,1.404 0.936,1.585 0.280,0.181 10 G40

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G40-12 (IL+2) - Body ground Light control switch tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the H56 navigation receiver assembly connector.


b.

Disconnect the G40 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-23 (SWG) - G40-4 (EAU) Always Below 1 Ω
H56-23 (SWG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
U170689E03
2.313,1.438 2.5,1.823 2.5,1.823 2.76,1.823 true 1.573,1.396 1.396,1.823 1.396,1.823 1.125,1.823 true 1.542,0.26 1.833,0.448 0.292,0.188 10 false H54 0.052,0 0.344,0.188 0.292,0.188 10 false *a 2.802,1.729 3.167,1.917 0.365,0.188 10 false ILL+ 0.729,1.74 1.188,1.927 0.458,0.188 10 false GND1

Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H54-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the G40 spiral cable sub-assembly connector.


b.

Disconnect the G76*1 or G163*2 driving support switch control ECU connector.

*1: for Manual Transmission

*2: for Automatic Transmission



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission
Tester Connection Condition Specified Condition
G40-10 (GND1) - G76-4 (SWI2) Always Below 1 Ω
G76-16 (GND) - Body ground Always 10 kΩ or higher
G76-4 (SWI2) - Body ground Always 10 kΩ or higher

for Automatic Transmission
Tester Connection Condition Specified Condition
G40-10 (GND1) - G163-14 (SWI2) Always Below 1 Ω
G163-7 (GND) - Body ground Always 10 kΩ or higher
G163-14 (SWI2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR