Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
|---|---|
| Illumination comes on for all components except steering pad switch assembly. | A |
| Illumination comes on for all components except radio and display receiver assembly. | B |
| Illumination comes on for all components except steering pad switch assembly and radio and display receiver assembly. | C |
| No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). | D |
A
B
C
D
Disconnect the spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G40-12 (IL+2) - Body ground | Light control switch tail or head position | 11 to 14 V |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
OK
NG
Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).
Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).
OK
NG
Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).
Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).
OK
NG
Disconnect the H51 radio and display receiver assembly connector.
Disconnect the G40 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H51-23 (SWG) - G40-4 (EAU) | Always | Below 1 Ω |
| H51-23 (SWG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H49-7 (GND1) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H49-10 (ILL+) - Body ground | Light control switch in the tail or head position | 11 to 14 V |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
OK
NG
Disconnect the G40 spiral cable sub-assembly connector.
Disconnect the G76*1 or G163*2 driving support switch control ECU connector.
*1: for Manual Transmission
*2: for Automatic Transmission
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-10 (GND1) - G76-4 (SWI2) | Always | Below 1 Ω |
| G76-16 (GND) - Body ground | Always | Below 1 Ω |
| G76-4 (SWI2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-10 (GND1) - G163-14 (SWI2) | Always | Below 1 Ω |
| G163-7 (GND) - Body ground | Always | Below 1 Ω |
| G163-14 (SWI2) - Body ground | Always | 10 kΩ or higher |
OK
NG