Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E278320E13
0.094,0.927 1.083,1.844 0.99,0.917 10 false Quarter Window Assembly (Window Glass Antenna Wire) 1.031,1.948 2,2.281 0.969,0.333 10 false Holder Antenna Assembly 3.406,2.229 4.635,2.594 1.229,0.365 10 false No. 2 Antenna Cord Sub-assembly 5.885,2.427 7.073,2.802 1.188,0.375 10 false Radio and Display Receiver Assembly 5.885,2.26 6.198,2.458 0.313,0.198 10 false RA 5.49,1.375 5.729,1.583 0.24,0.208 10 false 5 5.49,1.063 5.729,1.271 0.24,0.208 10 false 3 6.063,1.156 6.74,1.365 0.677,0.208 10 false RMAIN2 6.073,1.427 6.75,1.635 0.677,0.208 10 false ANT+ 2.281,1.073 2.521,1.281 0.24,0.208 10 false 3 2.271,1.354 2.51,1.563 0.24,0.208 10 false 1

PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.




OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.




OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the radio and display receiver assembly.


b.

Turn the engine switch on (ACC) with the radio and display receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




OK

4.INSPECT QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)

NG

4.INSPECT QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)
a.

Inspect the quarter window assembly (window glass antenna wire) (See page Audio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR).



OK

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the RA radio and display receiver assembly connector.


b.
E277921E01
1.063,0.781 1.281,0.781 1.281,0.781 1.531,1.042 true 2.333,0.635 2.083,0.635 2.083,0.635 1.833,0.885 true 2.354,1.583 2.104,1.583 2.104,1.583 1.833,1.271 true 0.677,0.698 1.208,0.885 0.531,0.188 10 false ANT+ 2.375,0.552 2.906,0.74 0.531,0.188 10 false 2 2.396,1.5 2.927,1.688 0.531,0.188 10 false 4

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Engine switch on (ACC)
Radio switch on
11 to 14 V




OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
U149470E04
1.583,1.26 1.219,1.667 1.219,1.667 0.99,1.667 false 2.01,0.958 2.302,0.729 2.302,0.729 2.531,0.729 false 0.115,0 0.313,0.208 0.198,0.208 10 false *a 2.583,0.646 2.958,0.854 0.375,0.208 10 false ANT+ 0.313,1.583 0.865,1.792 0.552,0.208 10 false RMAIN2 0.115,2.042 0.313,2.25 0.198,0.208 10 false *b 0.781,0.885 1.156,1.094 0.375,0.208 10 false RA

Disconnect the antenna connector from the radio and display receiver assembly.


b.

Disconnect the antenna connector from the holder antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (RMAIN2) - 3 Always Below 1 Ω
RA-5 (ANT+) - 1 Always Below 1 Ω
RA-3 (RMAIN2) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Holder Antenna Assembly)



OK

7.CHECK CHECK HOLDER ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.CHECK CHECK HOLDER ANTENNA ASSEMBLY
a.

Replace the holder antenna assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL).

OK:

Radio broadcasts can be received.




OK

END (HOLDER ANTENNA ASSEMBLY IS DEFECTIVE)

NG