This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1683 | Side Camera Feedback Malfunction | ·
Harness or connector ·
Parking assist ECU ·
Front passenger side television camera assembly ·
Front passenger side outer rear view mirror assembly |
| C1684 | Side Camera Current Malfunction | ·
Harness or connector ·
Parking assist ECU ·
Front passenger side television camera assembly ·
Front passenger side outer rear view mirror assembly |
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>CALIBRATION).
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1683 and C1684 are not output | A |
| DTC C1683 and/or C1684 is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Disconnect the I7 parking assist ECU connector.
Disconnect the J3*1 or K2*2 front passenger side outer rear view mirror assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-34 (SCV-) - J3-12 (SCV-) | Always | Below 1 Ω |
| I7-10 (SCV+) - J3-6 (SCV+) | Always | Below 1 Ω |
| I7-33 (SGND) - J3-13 (SGND) | Always | Below 1 Ω |
| I7-32 (SCB+) - J3-5 (SCB+) | Always | Below 1 Ω |
| I7-34 (SCV-) - Body ground | Always | 10 kΩ or higher |
| I7-10 (SCV+) - Body ground | Always | 10 kΩ or higher |
| I7-33 (SGND) - Body ground | Always | 10 kΩ or higher |
| I7-32 (SCB+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-34 (SCV-) - K2-12 (SCV-) | Always | Below 1 Ω |
| I7-10 (SCV+) - K2-6 (SCV+) | Always | Below 1 Ω |
| I7-33 (SGND) - K2-13 (SGND) | Always | Below 1 Ω |
| I7-32 (SCB+) - K2-5 (SCB+) | Always | Below 1 Ω |
| I7-34 (SCV-) - Body ground | Always | 10 kΩ or higher |
| I7-10 (SCV+) - Body ground | Always | 10 kΩ or higher |
| I7-33 (SGND) - Body ground | Always | 10 kΩ or higher |
| I7-32 (SCB+) - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-33 (SGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-32 (SCB+) - I7-33 (SGND) | Engine switch on (IG), wide view front and side monitor switch on | 5.5 to 7.05 V |
| *a | Component with harness connected
(Parking Assist ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Measure the waveform of the front passenger side television camera assembly using an oscilloscope.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
A waterproof connector is used for the side television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
The video waveform changes according to the image sent by the side television camera assembly.
| Item | Content |
|---|---|
| Tester Connection | I7-10 (SCV+) - I7-33 (SGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), wide view front and side monitor switch on, camera lens not covered, displaying image ·
Waveform B: Engine switch on (IG), wide view front and side monitor switch on, camera lens covered, blacking out screen |
Waveform is as shown in illustration.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Replace the front passenger side television camera assembly with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL).
NEXT
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1683 and C1684 are not output | A |
| DTC C1683 and/or C1684 is output | B |
A
B