Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  Reverse Signal Circuit  


DESCRIPTION

The navigation receiver assembly*1 or radio and display receiver assembly*2 receives a reverse signal from the park/neutral position switch assembly.

*1: for Navigation Receiver Type

*2: for Radio and Display Type


WIRING DIAGRAM

E323601E01
0.058,0 2.559,0.342 2.501,0.342 12 for Navigation Receiver Type: 1.328,2.027 1.996,2.221 0.668,0.194 10 C159 2.486,1.149 3.154,1.343 0.668,0.194 10 RL 5.242,1.13 5.909,1.324 0.668,0.194 10 REV 5.017,1.014 5.685,1.208 0.668,0.194 10 2 2.808,1.014 3.476,1.208 0.668,0.194 10 1 1.319,2.167 3.998,2.370 2.679,0.203 10 Park/Neutral Position Switch Assembly 4.751,2.02 5.419,2.214 0.668,0.194 10 H56 4.751,2.16 6.750,2.354 1.999,0.194 10 Navigation Receiver Assembly

E323601E02
0.058,0 2.559,0.342 2.501,0.342 12 for Radio and Display Type: 1.328,1.976 1.996,2.170 0.668,0.194 10 C159 2.486,1.119 3.154,1.313 0.668,0.194 10 RL 5.242,1.1 5.909,1.294 0.668,0.194 10 REV 5.017,0.983 5.685,1.177 0.668,0.194 10 2 2.808,0.983 3.476,1.177 0.668,0.194 10 1 1.319,2.137 3.961,2.370 2.642,0.233 10 Park/Neutral Position Switch Assembly 4.499,1.976 5.167,2.170 0.668,0.194 10 H51 4.499,2.13 6.942,2.324 2.443,0.194 10 Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point" (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION).



PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E225776

Enter the "Function check/setting I" mode and select "Vehicle Signal".


b.

Check that the display changes between ON and OFF according to the shift lever position.

Shift Lever Position Display
R ON
Except R OFF

HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Remove the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL).


b.

Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).


Result
Result Proceed to
OK (for Navigation Receiver Type) A
OK (for Radio and Display Type) B
NG C


A

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

C

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the H56 navigation receiver assembly connector.


b.

Disconnect the C159 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-2 (REV) - C159-1 (RL) Always Below 1 Ω
H56-2 (REV) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the C159 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-2 (REV) - C159-1 (RL) Always Below 1 Ω
H51-2 (REV) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR