Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2016.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors, double lock door control relay assembly*1 and sliding roof drive gear sub-assembly*2. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors, double lock door control relay assembly*1 and sliding roof drive gear sub-assembly*2 is detected consecutively 3 times.

*1: w/ Double Locking System

*2: w/ Sliding Roof System


DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors, double lock door control relay assembly*2 and sliding roof drive gear sub-assembly*3 consecutively 3 times.
·

Multiplex network master switch assembly

·

Front power window regulator motor assembly LH

·

Front power window regulator motor assembly RH

·

Rear power window regulator motor assembly LH*1

·

Rear power window regulator motor assembly RH*1

·

Double lock door control relay*2

·

Sliding roof drive gear sub-assembly*3

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



*1: for 5 Door

*2: w/ Double Locking System

*3: w/ Sliding Roof System


WIRING DIAGRAM

C212388E03
5.25,0.813 5.552,0.99 0.302,0.177 10 false A 5.74,0.385 6.094,0.563 0.354,0.177 10 false LIN2 3.5,2.052 3.771,2.229 0.271,0.177 10 false LIN 1.229,0.396 1.5,0.573 0.271,0.177 10 false LIN 3.469,0.396 3.781,0.573 0.313,0.177 10 false LIN1 3.854,0.302 4.063,0.479 0.208,0.177 10 false 17 3.125,0.396 3.448,0.573 0.323,0.177 10 false LIN2 2.844,0.302 3.052,0.479 0.208,0.177 10 false 16 5.49,0.302 5.667,0.479 0.177,0.177 10 false 16 3.844,1.958 3.979,2.135 0.135,0.177 10 false 9 1.573,0.302 1.708,0.479 0.135,0.177 10 false 9 3.521,3.094 3.792,3.271 0.271,0.177 10 false LIN 5.729,3.104 6,3.281 0.271,0.177 10 false LIN 3.865,3.01 4,3.188 0.135,0.177 10 false 9 5.542,3.01 5.677,3.188 0.135,0.177 10 false 9 5.74,4.854 6.156,5.031 0.417,0.177 10 false MPX1 5.542,4.781 5.677,4.958 0.135,0.177 10 false 4 5.25,0.979 6.938,1.354 1.688,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 2.75,0.875 3.917,1.052 1.167,0.177 10 false K4*1, J9*2 2.75,1.052 4.417,1.385 1.667,0.333 10 false Multiplex Network Master Switch Assembly 0.063,0.823 0.969,1 0.906,0.177 10 false K7*1, J7*2 0.063,0.969 2.042,1.344 1.979,0.375 10 false Front Power Window Regulator Motor Assembly LH*1, RH*2 1.615,1.927 3.021,2.479 1.406,0.552 10 false Front Power Window Regulator Motor Assembly RH*1, LH*2 1.615,1.75 2.5,1.927 0.885,0.177 10 false J7*1, K7*2 1.719,2.875 2.125,3.052 0.406,0.177 10 false M4 0.094,6.24 2.104,6.417 2.01,0.177 10 false *4: w/ Double Locking System 0.094,6.51 2.104,6.688 2.01,0.177 10 false *5: w/ Sliding Roof System 0.094,5.698 1.021,5.875 0.927,0.177 10 false *2: for RHD 0.094,5.427 1.021,5.604 0.927,0.177 10 false *1: for LHD 0.094,5.969 1.021,6.146 0.927,0.177 10 false *3: for 5 Door 1.719,3.052 3.021,3.594 1.302,0.542 10 false Rear Power Window Regulator Motor Assembly LH*3 3.375,4.875 3.792,5.052 0.417,0.177 10 false MPX1 3.844,4.781 4.031,4.958 0.188,0.177 10 false 9 1.823,4.594 2.229,4.771 0.406,0.177 10 false G49 1.813,4.76 3.021,5.313 1.208,0.552 10 false Double Lock Door Control Relay Assembly*4 5.042,3.552 5.448,3.729 0.406,0.177 10 false L4 5.042,3.698 7.021,4.031 1.979,0.333 10 false Rear Power Window Regulator Motor Assembly RH*3 5.375,5.302 5.781,5.479 0.406,0.177 10 false W2 5.375,5.458 6.823,5.906 1.448,0.448 10 false Sliding Roof Drive Gear Sub-assembly*5

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for the LIN communication stop DTC. Then perform troubleshooting for DTC B2325.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2325 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A-16 (LIN2) - K4-17 (LIN1) Always Below 1 Ω
A-16 (LIN2) or K4-17 (LIN1) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
A-16 (LIN2) - J9-17 (LIN1) Always Below 1 Ω
A-16 (LIN2) or J9-17 (LIN1) - Body ground Always 10 kΩ or higher




OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC

*1: for LHD

*2: for RHD


a.

Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


b.

Reconnect the K4*1 or J9*2 multiplex network master switch assembly connector.


c.

Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.




NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

6.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

6.CLEAR DTC

*1: for LHD

*2: for RHD


a.

Connect the K7*1 or J7*2 front power window regulator motor assembly connector.


b.

Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.




NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

8.CLEAR DTC

B

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

8.CLEAR DTC

*1: for LHD

*2: for RHD


a.

Connect the K4*1 or J9*2 multiplex network master switch assembly connector.


b.

Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (for 5 Door) A
DTC B2325 is output (for 3 Door, w/ Double Locking System) B
DTC B2325 is output (for 3 Door, w/o Double Locking System, w/ Sliding Roof System) C
DTC B2325 is output (for 3 Door, w/o Double Locking System, w/o Sliding Roof System) D
DTC B2325 is not output E



A

10.CLEAR DTC

B

18.CLEAR DTC

C

20.CLEAR DTC

D

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

E

OTHERS FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

10.CLEAR DTC
a.

Connect the K7*1 or J7*2 front power window regulator motor assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the L4 rear power window regulator motor assembly RH connector.




NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

12.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

12.CLEAR DTC
a.

Connect the L4 rear power window regulator motor assembly RH connector.


b.

Disconnect the M4 rear power window regulator motor assembly LH connector.




NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (w/ Double Locking System) A
DTC B2325 is output (w/o Double Locking System, w/ Sliding Roof System) B
DTC B2325 is output (w/o Double Locking System, w/o Sliding Roof System) C
DTC B2325 is not output D



A

14.CLEAR DTC

B

16.CLEAR DTC

C

CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

14.CLEAR DTC
a.

Connect the M4 rear power window regulator motor assembly LH connector.


b.

Disconnect the G49 double lock door control relay assembly connector.




NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/o Sliding Roof System) B
DTC B2325 is not output C



A

16.CLEAR DTC

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

16.CLEAR DTC
a.

w/ Double Locking System:

i.

Connect the G49 double lock door control relay assembly connector.



b.

w/o Double Locking System:

i.

Connect the M4 rear power window regulator motor assembly LH connector.



c.

Disconnect the W2 sliding roof drive gear sub-assembly connector.




NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

18.CLEAR DTC
a.

Connect the K7*1 or J7*2 front power window regulator motor assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G49 double lock door control relay assembly connector.




NEXT

19.CHECK FOR DTC
19.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/o Sliding Roof System) B
DTC B2325 is not output C



A

20.CLEAR DTC

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

20.CLEAR DTC
a.

w/ Double Locking System:

i.

Connect the G49 double lock door control relay assembly connector.



b.

w/o Double Locking System:

i.

Connect the K7*1 or J7*2 front power window regulator motor assembly connector.

*1: for LHD

*2: for RHD




c.

Disconnect the W2 sliding roof drive gear sub-assembly connector.




NEXT

21.CHECK FOR DTC
21.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY