Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U1002  Lost Communication with Gateway Module (MS Bus)  


DESCRIPTION

·

The main body ECU (multiplex network body ECU) stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.

·

When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU (multiplex network body ECU) determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 (CAN MS BUS) Lost communication with the gateway module (MS bus).
·

MS bus circuit

·

Main body ECU (multiplex network body ECU) CAN main wire or connector

·

Front power seat switch LH CAN branch wire or connector*1

·

Multiplex tilt and telescopic ECU CAN branch wire or connector*2

·

Driving support switch control ECU CAN branch wire or connector*3

·

Main body ECU (multiplex network body ECU)

·

Front power seat switch LH*1

·

Multiplex tilt and telescopic ECU*2

·

Driving monitor switch control ECU*3

·

No. 3 junction connector

·

No. 8 junction connector



*1: w/ Seat Position Memory

*2: for Power Tilt and Power Telescopic Steering Column

*3: w/ Multi-function Switch


WIRING DIAGRAM

C294685E03
1.49,2.906 1.854,3.052 0.365,0.146 10 false G76 0.927,1.396 1.344,1.542 0.417,0.146 10 false CANN 0.927,0.927 1.344,1.073 0.417,0.146 10 false CANP 0.927,3.385 1.344,3.531 0.417,0.146 10 false CANN 0.927,2.906 1.344,3.052 0.417,0.146 10 false CANP 5.979,3.385 6.396,3.531 0.417,0.146 10 false CANN 5.979,2.906 6.396,3.052 0.417,0.146 10 false CANP 5.979,1.49 6.396,1.635 0.417,0.146 10 false CANN 5.979,0.781 6.396,0.927 0.417,0.146 10 false CANP 1.458,1.26 1.875,1.406 0.417,0.146 10 false 7 1.458,0.792 1.875,0.938 0.417,0.146 10 false 8 3.146,1.26 3.563,1.406 0.417,0.146 10 false 13 3.198,0.802 3.615,0.948 0.417,0.146 10 false 2 3.146,3.26 3.563,3.406 0.417,0.146 10 false 16 3.219,2.76 3.635,2.906 0.417,0.146 10 false 5 5.719,3.26 6.135,3.406 0.417,0.146 10 false 14 5.781,2.802 6.198,2.948 0.417,0.146 10 false 5 5.698,1.271 6.115,1.417 0.417,0.146 10 false 10 5.469,1.625 5.885,1.771 0.417,0.146 10 false G63 5.479,1.781 7.135,2.281 1.656,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 5.781,3.719 6.198,3.865 0.417,0.146 10 false G116 5.792,3.885 6.969,4.229 1.177,0.344 10 false Multiplex Tilt and Telescopic ECU*2 5.469,5.625 5.885,5.771 0.417,0.146 10 false G103 5.479,5.76 7.083,6.104 1.604,0.344 10 false No. 8 Junction Connector 2.833,5.594 3.25,5.74 0.417,0.146 10 false G96 2.844,5.76 4.448,6.104 1.604,0.344 10 false No. 3 Junction Connector 0.219,4.5 2.01,4.677 1.792,0.177 10 false *1: w/ Seat Position Memory 0.219,4.854 2.01,5.198 1.792,0.344 10 false *2: for Power Tilt and Power Telescopic Steering Column 0.219,5.563 2.01,5.906 1.792,0.344 10 false *3: w/ Multi-function Switch 0.219,5.917 2.177,6.26 1.958,0.344 10 false *4: for Automatic Transmission 0.219,6.26 2.177,6.604 1.958,0.344 10 false *5: for Manual Transmission 5.76,0.792 6.177,0.938 0.417,0.146 10 false 9 5.979,5.479 6.396,5.625 0.417,0.146 10 false CANN 5.979,4.76 6.396,4.906 0.417,0.146 10 false CANP 5.76,5.26 6.177,5.406 0.417,0.146 10 false 2 5.75,4.781 6.167,4.927 0.417,0.146 10 false 3 4.021,1.271 4.438,1.417 0.417,0.146 10 false 15 4.042,0.802 4.458,0.948 0.417,0.146 10 false 4 4.021,3.229 4.438,3.375 0.417,0.146 10 false 14 4.021,2.781 4.438,2.927 0.417,0.146 10 false 3 4.021,5.25 4.438,5.396 0.417,0.146 10 false 17 4.021,4.792 4.438,4.938 0.417,0.146 10 false 6 0.177,1.615 0.542,1.76 0.365,0.146 10 false b5 1.49,3.365 1.854,3.51 0.365,0.146 10 false G76 0.229,3.729 1.667,4.188 1.438,0.458 10 false Driving Support Switch Control ECU*3 0.177,1.76 2.146,2.094 1.969,0.333 10 false Front Power Seat Switch LH*1 1.5,2.698 1.865,2.844 0.365,0.146 10 false 9*5 1.5,3.156 1.865,3.302 0.365,0.146 10 false 10*5 1.885,2.917 2.25,3.063 0.365,0.146 10 false G163 1.885,3.365 2.25,3.51 0.365,0.146 10 false G163 1.948,2.708 2.313,2.854 0.365,0.146 10 false 2*4 1.948,3.146 2.313,3.292 0.365,0.146 10 false 3*4

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
2.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
a.
U148571E04
1.74,0.875 1.406,0.24 1.406,0.24 1.313,0.24 false 1.438,0.885 1.24,0.531 1.24,0.531 1.146,0.531 false 2.156,2.771 2.365,3 2.365,3 2.469,3 false 1.688,2.448 1.5,2.167 1.5,2.167 1.396,2.167 false 0.104,1.958 0.323,2.156 0.219,0.198 10 false *b 0.104,0.073 0.323,0.271 0.219,0.198 10 false *a 0.885,0.156 1.313,0.354 0.427,0.198 10 false CANN 0.719,0.448 1.167,0.646 0.448,0.198 10 false CANP 2.521,2.927 2.833,3.125 0.313,0.198 10 false BAT 0.438,2.594 0.729,2.792 0.292,0.198 10 false G48 0.438,0.979 0.813,1.177 0.375,0.198 10 false G103 1.135,2.083 1.385,2.281 0.25,0.198 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G103-3 (CANP) - G103-2 (CANN) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
G103-3 (CANP) - G103-2 (CANN) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G103-3 (CANP) - G48-16 (BAT) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G103-2 (CANN) - G48-16 (BAT) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G103-3 (CANP) - G48-4 (CG) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
G103-2 (CANN) - G48-4 (CG) Engine switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(No. 8 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

B

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH)

C

24.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U148873E01
0.06,0.039 0.267,0.227 0.207,0.188 10 *a 2.385,0.582 2.808,0.727 0.423,0.144 10 CANH 2.353,1.663 2.741,1.807 0.389,0.144 10 CANL 2.35,0.65 2.266,0.65 2.266,0.65 1.904,1.09 false 1.903,1.291 2.172,1.747 2.172,1.747 2.318,1.747 false 0.518,1.092 0.803,1.231 0.284,0.139 10 G96

Disconnect the G96 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-4 (CANH) - G96-15 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)
a.
U148874E01
0.06,0.039 0.267,0.227 0.207,0.188 10 *a 2.349,0.582 2.772,0.727 0.423,0.144 10 CANH 2.183,1.663 2.571,1.807 0.389,0.144 10 CANL 2.314,0.65 2.229,0.65 2.229,0.65 1.734,1.09 false 1.733,1.291 2.002,1.747 2.002,1.747 2.148,1.747 false 0.519,1.092 0.801,1.231 0.283,0.139 10 G96

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-6 (CANH) - G96-17 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

7.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
a.
U148572E02
1.875,0.208 1.813,0.208 1.813,0.208 1.479,1.177 false 2.26,0.479 2.188,0.479 2.188,0.479 1.583,1.188 false 1.906,0.135 2.344,0.313 0.438,0.177 10 false CANP 0.25,0.948 0.573,1.125 0.323,0.177 10 false G63 0.052,0.063 0.26,0.24 0.208,0.177 10 false *a 2.302,0.406 2.74,0.583 0.438,0.177 10 false CANN

Disconnect the G63 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G63-9 (CANP) - G63-10 (CANN) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)

7.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148307E02
1.781,0.323 1.719,0.323 1.719,0.323 1.385,0.875 false 2.521,1.552 2.458,1.552 2.458,1.552 1.781,1.031 false 1.823,0.25 2.26,0.427 0.438,0.177 10 false CANP 0.417,0.885 0.823,1.063 0.406,0.177 10 false G103 0.104,0.01 0.313,0.188 0.208,0.177 10 false *a 2.552,1.469 2.99,1.646 0.438,0.177 10 false CANN

Disconnect the G103 No. 8 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G103-3 (CANP) - G103-2 (CANN) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)



OK

REPLACE NO. 8 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH)
NOTICE:

For vehicles without a seat position memory, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Multiplex Tilt and Telescopic ECU)".


a.
U148751E03
2.219,2.958 2.427,3.125 2.427,3.125 2.51,3.125 false 1.625,2.521 1.198,2.167 1.198,2.167 1.115,2.167 false 2.573,0.813 2.5,0.813 2.5,0.813 2.188,1.156 false 2.573,1.625 2.51,1.625 2.51,1.625 2.177,1.354 false 2.552,3.052 2.99,3.229 0.438,0.177 10 false BAT 0.844,2.094 1.073,2.271 0.229,0.177 10 false CG 2.604,0.74 3.042,0.917 0.438,0.177 10 false CANH 2.615,1.552 3.052,1.729 0.438,0.177 10 false CANL 0.49,1.125 0.781,1.302 0.292,0.177 10 false G96 0.448,2.677 0.771,2.854 0.323,0.177 10 false G48 0.135,2.281 0.344,2.458 0.208,0.177 10 false *b 0.135,0.031 0.344,0.208 0.208,0.177 10 false *a

Disconnect the G96 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-2 (CANH) - G96-13 (CANL) Engine switch off 200 Ω or higher
G96-2 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-2 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G96-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

NG

14.CONNECT CONNECTOR
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
NOTICE:

For vehicles without a power tilt and telescopic steering column, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Driving Support Switch Control ECU)".


a.
U148752E03
2.229,2.938 2.438,3.104 2.438,3.104 2.521,3.104 false 1.635,2.51 1.208,2.156 1.208,2.156 1.125,2.156 false 2.563,0.802 2.49,0.802 2.49,0.802 2.083,1.146 false 2.563,1.635 2.5,1.635 2.5,1.635 2.083,1.365 false 2.521,3 2.958,3.177 0.438,0.177 10 false BAT 0.854,2.083 1.083,2.26 0.229,0.177 10 false CG 2.594,0.74 3.031,0.917 0.438,0.177 10 false CANH 2.615,1.573 3.052,1.75 0.438,0.177 10 false CANL 0.5,1.125 0.802,1.302 0.302,0.177 10 false G96 0.448,2.688 0.771,2.865 0.323,0.177 10 false G48 0.135,2.281 0.344,2.458 0.208,0.177 10 false *b 0.135,0.031 0.344,0.208 0.208,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-3 (CANH) - G96-14 (CANL) Engine switch off 200 Ω or higher
G96-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G96-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU)

NG

16.CONNECT CONNECTOR
11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU)
NOTICE:

For vehicles without a multi-function switch, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Main Body ECU)".


a.
U148758E03
2.229,2.938 2.438,3.104 2.438,3.104 2.521,3.104 false 1.635,2.521 1.208,2.167 1.208,2.167 1.125,2.167 false 2.5,0.656 2.427,0.656 2.427,0.656 1.844,1.156 false 2.26,1.885 2.198,1.885 2.198,1.885 1.844,1.365 false 2.521,3 2.958,3.177 0.438,0.177 10 false BAT 0.896,2.094 1.125,2.271 0.229,0.177 10 false CG 2.531,0.573 3.052,0.771 0.521,0.198 10 false CANH 2.302,1.823 2.792,2.01 0.49,0.188 10 false CANL 0.5,1.115 0.802,1.292 0.302,0.177 10 false G96 0.458,2.677 0.75,2.854 0.292,0.177 10 false G48 0.135,2.281 0.344,2.458 0.208,0.177 10 false *b 0.135,0.031 0.344,0.208 0.208,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-5 (CANH) - G96-16 (CANL) Engine switch off 200 Ω or higher
G96-5 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-16 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-5 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G96-16 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

18.CONNECT CONNECTOR
12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U148753E03
2.229,2.938 2.438,3.104 2.438,3.104 2.521,3.104 false 1.635,2.521 1.208,2.167 1.208,2.167 1.125,2.167 false 2.563,0.813 2.49,0.813 2.49,0.813 1.969,1.156 false 2.573,1.635 2.51,1.635 2.51,1.635 1.969,1.365 false 2.521,3 2.958,3.177 0.438,0.177 10 false BAT 0.875,2.094 1.104,2.271 0.229,0.177 10 false CG 2.594,0.74 3.031,0.917 0.438,0.177 10 false CANH 2.615,1.563 3.052,1.74 0.438,0.177 10 false CANL 0.49,1.115 0.792,1.292 0.302,0.177 10 false G96 0.448,2.677 0.771,2.854 0.323,0.177 10 false G48 0.135,2.281 0.344,2.458 0.208,0.177 10 false *b 0.135,0.031 0.344,0.208 0.208,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-4 (CANH) - G96-15 (CANL) Engine switch off 108 to 132 Ω
G96-4 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-15 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-4 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G96-15 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)

NG

20.CONNECT CONNECTOR
13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)
a.
U148759E03
2.229,2.938 2.438,3.104 2.438,3.104 2.521,3.104 false 1.635,2.552 1.208,2.135 1.208,2.135 1.125,2.135 false 2.448,0.49 2.385,0.49 2.385,0.49 1.74,1.156 false 2.323,1.948 2.26,1.948 2.26,1.948 1.74,1.354 false 2.521,3 2.958,3.177 0.438,0.177 10 false BAT 0.833,2.042 1.063,2.219 0.229,0.177 10 false CG 2.479,0.406 2.99,0.604 0.51,0.198 10 false CANH 2.396,1.865 2.833,2.01 0.438,0.146 10 false CANL 0.51,1.125 0.813,1.302 0.302,0.177 10 false G96 0.458,2.677 0.74,2.854 0.281,0.177 10 false G48 0.135,2.281 0.344,2.458 0.208,0.177 10 false *b 0.135,0.031 0.344,0.208 0.208,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-6 (CANH) - G96-17 (CANL) Engine switch off 108 to 132 Ω
G96-6 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-17 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G96-6 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G96-17 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

22.CONNECT CONNECTOR
14.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

15.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH LH)
15.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH LH)
a.
U148776E03
2.271,1.49 2.708,1.104 2.708,1.104 2.792,1.104 false 2.188,1.521 2.625,1.906 2.625,1.906 2.708,1.906 false 2.354,3.042 2.563,3.208 2.563,3.208 2.646,3.208 false 1.729,2.583 1.302,2.229 1.302,2.229 1.219,2.229 false 2.844,1.031 3.281,1.208 0.438,0.177 10 false CANN 2.75,1.833 3.188,2.01 0.438,0.177 10 false CANP 1.271,1.271 1.594,1.448 0.323,0.177 10 false b5 0.354,2.729 0.677,2.906 0.323,0.177 10 false G48 0.104,2.167 0.313,2.344 0.208,0.177 10 false *b 2.646,3.115 3.083,3.292 0.438,0.177 10 false BAT 0.104,0.021 0.313,0.198 0.208,0.177 10 false *a 0.927,2.125 1.156,2.302 0.229,0.177 10 false CG

Disconnect the b5 front power seat switch LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
b5-8 (CANP) - b5-7 (CANN) Engine switch off 54 to 69 Ω
b5-8 (CANP) - G48-4 (CG) Engine switch off 200 Ω or higher
b5-7 (CANN) - G48-4 (CG) Engine switch off 200 Ω or higher
b5-8 (CANP) - G48-16 (BAT) Engine switch off 6 kΩ or higher
b5-7 (CANN) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Switch LH)
*b Front view of DLC3



OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FRONT POWER SEAT SWITCH LH (CANP, CANN)

16.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

17.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
17.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
a.
U148573E04
2.531,0.896 2.448,0.896 2.448,0.896 2.104,1.333 false 2.615,1.958 2.531,1.958 2.531,1.958 2.104,1.51 false 2.198,2.938 2.406,3.167 2.406,3.167 2.458,3.167 false 1.667,2.594 1.469,2.25 1.469,2.25 1.417,2.25 false 0.115,0.063 0.313,0.271 0.198,0.208 10 false *a 2.656,1.875 3.083,2.083 0.427,0.208 10 false CANP 2.573,0.823 3,1.031 0.427,0.208 10 false CANN 1.052,1.458 1.438,1.667 0.385,0.208 10 false G116 0.125,1.969 0.323,2.135 0.198,0.167 10 false *b 0.521,2.698 0.844,2.875 0.323,0.177 10 false G48 1.115,2.146 1.344,2.323 0.229,0.177 10 false CG 2.5,3.083 2.854,3.26 0.354,0.177 10 false BAT

Disconnect the G116 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G116-5 (CANP) - G116-14 (CANN) Engine switch off 54 to 69 Ω
G116-5 (CANP) - G48-4 (CG) Engine switch off 200 Ω or higher
G116-14 (CANN) - G48-4 (CG) Engine switch off 200 Ω or higher
G116-5 (CANP) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G116-14 (CANN) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
*b Front view of DLC3



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANP, CANN)

18.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

19.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT SWITCH CONTROL ECU)
19.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT SWITCH CONTROL ECU)
a.

for Automatic Transmission:

i.
U148940E02
1.365,2.021 1.469,2.021 1.469,2.021 1.708,2.448 false 2.563,3.156 2.458,3.156 2.458,3.156 2.333,2.927 false 1.427,1.063 1.125,0.76 1.125,0.76 1.01,0.76 false 1.573,1.083 1.292,0.448 1.292,0.448 1.167,0.448 false 0.063,0.01 0.24,0.177 0.177,0.167 10 false *a 0.063,1.719 0.24,1.885 0.177,0.167 10 false *b 1.115,1.948 1.375,2.104 0.26,0.156 10 false CG 2.594,3.073 2.938,3.229 0.344,0.156 10 false BAT 0.708,0.365 1.156,0.594 0.448,0.229 10 false CANN 0.573,0.698 1.01,0.896 0.438,0.198 10 false CANP 2.604,1.146 3.01,1.323 0.406,0.177 10 false G163 0.406,2.625 0.76,2.865 0.354,0.24 10 false G48

Disconnect the G163 driving support switch control ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G163-2 (CANP) - G163-3 (CANN) Engine switch off 54 to 69 Ω
G163-2 (CANP) - G48-4 (CG) Engine switch off 200 Ω or higher
G163-3 (CANN) - G48-4 (CG) Engine switch off 200 Ω or higher
G163-2 (CANP) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G163-3 (CANN) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Driving Support Switch Control ECU)
*b Front view of DLC3



b.

for Manual Transmission:

i.
U170151E02
1.396,1.865 1.51,1.865 1.51,1.865 1.854,1.458 false 2.333,1.792 2.219,1.792 2.219,1.792 1.948,1.469 false 2.344,2.927 2.552,3.167 2.552,3.167 2.677,3.167 false 1.688,2.49 1.479,2.083 1.479,2.083 1.354,2.083 false 0.073,0.021 0.271,0.229 0.198,0.208 10 false *a 2.365,1.729 2.792,1.938 0.427,0.208 10 false CANP 0.938,1.781 1.365,1.99 0.427,0.208 10 false CANN 0.438,1.292 0.76,1.479 0.323,0.188 10 false G76 0.083,1.927 0.281,2.094 0.198,0.167 10 false *b 1.052,1.979 1.281,2.156 0.229,0.177 10 false CG 2.719,3.073 3.073,3.25 0.354,0.177 10 false BAT 0.344,2.625 0.667,2.823 0.323,0.198 10 false G48

Disconnect the G76 driving support switch control ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G76-9 (CANP) - G76-10 (CANN) Engine switch off 54 to 69 Ω
G76-9 (CANP) - G48-4 (CG) Engine switch off 200 Ω or higher
G76-10 (CANN) - G48-4 (CG) Engine switch off 200 Ω or higher
G76-9 (CANP) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G76-10 (CANN) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Driving Support Switch Control ECU)
*b Front view of DLC3




OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DRIVING SUPPORT SWITCH CONTROL ECU (CANP, CANN)

20.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

21.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
21.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U148574E04
1.604,1.125 2.042,0.427 2.042,0.427 2.125,0.427 false 1.51,1.167 1.948,1.875 1.948,1.875 2.031,1.875 false 2.344,2.927 2.552,3.094 2.552,3.094 2.635,3.094 false 1.677,2.469 1.26,2.052 1.26,2.052 1.177,2.052 false 2.167,0.344 2.604,0.521 0.438,0.177 10 false CANN 2.052,1.792 2.49,1.969 0.438,0.177 10 false CANP 0.302,1.104 0.625,1.281 0.323,0.177 10 false G63 0.396,2.563 0.719,2.74 0.323,0.177 10 false G48 0.042,2.167 0.25,2.344 0.208,0.177 10 false *b 2.646,3 3.083,3.177 0.438,0.177 10 false BAT 0.042,0.021 0.25,0.198 0.208,0.177 10 false *a 0.885,1.958 1.115,2.135 0.229,0.177 10 false CG

Disconnect the G63 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G63-9 (CANP) - G63-10 (CANN) Engine switch off 108 to 132 Ω
G63-9 (CANP) - G48-4 (CG) Engine switch off 200 Ω or higher
G63-10 (CANN) - G48-4 (CG) Engine switch off 200 Ω or higher
G63-9 (CANP) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G63-10 (CANN) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)

22.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR)
23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR)
a.
U148904E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.377,0.891 1.161,1.222 1.161,1.222 1.029,1.222 false 1.338,0.314 1.478,0.314 1.478,0.314 1.691,0.708 false 0.08,0.078 0.316,0.314 0.237,0.237 10 *a 0.08,1.909 0.316,2.146 0.237,0.237 10 *b 0.826,0.228 1.247,0.370 0.421,0.142 10 CANN 0.511,1.145 0.934,1.287 0.424,0.142 10 CANP 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.406,2.69 0.692,2.830 0.286,0.140 10 G48 2.538,0.768 2.895,0.908 0.357,0.140 10 G103

Disconnect the G103 No. 8 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G103-3 (CANP) - G103-2 (CANN) Engine switch off 108 to 132 Ω
G103-3 (CANP) - G48-4 (CG) Engine switch off 200 Ω or higher
G103-2 (CANN) - G48-4 (CG) Engine switch off 200 Ω or higher
G103-3 (CANP) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G103-2 (CANN) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 8 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

24.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

U148500E03
5.854,0.521 5.917,0.521 5.917,0.521 6.156,1.156 false 3.781,0.531 3.844,0.531 3.844,0.531 4.083,1.167 false 6.427,0.521 6.365,0.521 6.365,0.521 6.271,1.156 false 6.667,0.833 6.594,0.833 6.594,0.833 6.396,1.156 false 0.594,0.552 0.656,0.552 0.656,0.552 0.854,0.917 false 6.25,1.542 6.323,1.542 6.323,1.542 6.51,1.219 false 3.396,0.458 3.813,0.625 0.417,0.167 10 false GND1 5.531,0.438 5.844,0.604 0.313,0.167 10 false ACC 6.458,0.438 6.896,0.604 0.438,0.167 10 false BECU 6.708,0.75 7.094,0.917 0.385,0.167 10 false ALTB 2.406,0.021 2.604,0.25 0.198,0.229 10 false *b 0.021,0.021 0.219,0.25 0.198,0.229 10 false *a 0.188,0.469 0.615,0.635 0.427,0.167 10 false GND2 0.167,0.927 0.479,1.094 0.313,0.167 10 false G63 2.406,1.083 2.542,1.25 0.135,0.167 10 false A 6.083,1.458 6.26,1.625 0.177,0.167 10 false IG

Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G63-3 (GND2) - Body ground Always Below 1 Ω
A-11 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-30 (BECU) - Body ground Always 11 to 14 V
A-31 (ALTB) - Body ground Always 11 to 14 V
A-29 (ACC) - Body ground Engine switch on (ACC) 11 to 14 V
A-32 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR