Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261039 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all the doors by sending lock/unlock signals to each door.

WIRING DIAGRAM

B242194E02
0.699,2.952 2.132,3.128 1.434,0.177 10 Door Control Receiver 0.699,2.767 1.019,2.943 0.320,0.177 10 R26 2.055,0.712 2.376,0.889 0.320,0.177 10 3 1.601,0.805 1.957,0.982 0.356,0.177 10 PRG 2.055,1.212 2.376,1.388 0.320,0.177 10 2 4.983,2.178 5.303,2.355 0.320,0.177 10 G64 1.605,1.305 1.945,1.481 0.341,0.177 10 RDA 2.055,1.704 2.376,1.880 0.320,0.177 10 5 1.73,1.796 1.946,1.973 0.217,0.177 10 +B 2.055,2.15 2.376,2.326 0.320,0.177 10 1 1.611,2.243 1.945,2.419 0.334,0.177 10 GND 5.22,0.805 5.637,0.982 0.417,0.177 10 PRG 5.22,1.293 5.622,1.470 0.402,0.177 10 RDA 4.967,0.709 5.385,0.885 0.417,0.177 10 25 4.967,1.211 5.385,1.387 0.417,0.177 10 26 4.984,2.362 6.702,2.688 1.718,0.326 10 Main Body ECU (Multiplex Network Body ECU) 3.179,2.281 4.052,2.461 0.872,0.181 10 from Battery 2.464,1.922 2.941,2.103 0.477,0.181 10 ECU-B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the door control receiver, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)>REGISTRATION).



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Each door locks and unlocks normally.




OK

2.CHECK KEY REMINDER WARNING OPERATION

NG

2.CHECK KEY REMINDER WARNING OPERATION
a.

Check the key reminder buzzer operation (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK).

HINT:

If the key reminder buzzer is functioning normally, it can be assumed that the unlock warning switch is also functioning normally.


OK:

Key reminder buzzer operates normally.




OK

3.CHECK WIRELESS DOOR CONTROL TRANSMITTER

NG

3.CHECK WIRELESS DOOR CONTROL TRANSMITTER
a.

Check whether the wireless door lock control functions operate normally with another registered transmitter.

OK:

Wireless door lock control functions operate normally.




OK

4.CHECK TRANSMITTER BATTERY

NG

5.CHECK FOR ELECTRICAL NOISE
4.CHECK TRANSMITTER BATTERY
a.

Remove the battery from the inoperative wireless door control transmitter (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Entry and Start System)>REPLACEMENT).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Always 2.5 to 3.2 V




OK

REPLACE DOOR CONTROL TRANSMITTER

NG

5.CHECK FOR ELECTRICAL NOISE
a.

Move the transmitter in the vicinity of the door control receiver.

HINT:

Refer to Parts Location for the location of the door control receiver (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)>PARTS LOCATION).



b.

Press and hold either the lock or unlock transmitter switch for 1 second, and check that the doors are locked or unlocked accordingly.

OK:

Wireless door lock control functions operate normally.


HINT:
·

Check if electrical noise is the cause by moving the door control transmitter closer to the door control receiver. Moving closer will decrease the effects of electrical noise.

·

If the operation check can be performed normally, there is a high probability that electrical noise or a decrease in output from the door control transmitter is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.





OK

FIND CAUSE OF ELECTRICAL NOISE AND REMOVE IT

NG

6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU)
6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU)
a.

Disconnect the R26 receiver connector.


b.

Disconnect the G64 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R26-2 (RDA) - G64-26 (RDA) Always Below 1 Ω
R26-3 (PRG) - G64-25 (PRG)
R26-2 (RDA) or G64-26 (RDA) - Body ground Always 10 kΩ or higher
R26-3 (PRG) or G64-25 (PRG) - Body ground




OK

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
U169656E01
0.714,1.841 1.062,2.027 0.349,0.186 10 GND 2.311,1.841 2.532,2.027 0.221,0.186 10 +B 0.142,0.062 0.337,0.248 0.195,0.186 10 *a 0.452,1.067 0.801,1.253 0.349,0.186 10 R26 1.224,1.355 1.048,1.845 false 2.207,1.355 2.352,1.841 false

Disconnect the R26 receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R26-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
R26-5 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)



OK

8.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.
B449871E01
0.719,1.167 1.167,1.417 0.448,0.25 1.823,1.833 2.323,2.156 true 0.156,0.031 2.448,0.417 2.292,0.385 10 false Component with harness connected: (Door Control Receiver) 0.833,1.219 1.146,1.469 0.313,0.25 10 false R26 2.406,2.094 2.719,2.344 0.313,0.25 10 false RDA 0.219,2.51 1.875,2.76 1.656,0.25 10 false RDA Output (Reference): 1.229,2.958 2.885,3.208 1.656,0.25 10 false Transmitter Switch On 0.458,3.344 0.771,3.594 0.313,0.25 10 false 10 V 0.094,4.146 0.844,4.406 0.75,0.26 10 false Below 1 V 1.521,4.281 2.344,4.531 0.823,0.25 10 false 50 μsec.

Using an oscilloscope, check the waveform.

Measurement Condition
Item Content
Tester Connection R26-2 (RDA) - Body ground
Tool Setting 10 V/DIV., 50 μs/DIV.
Condition No key in ignition key cylinder, all doors closed and transmitter switch off → on

OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
OK A
NG (for 5 Door) B
NG (for 3 Door) C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

C