Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261054 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Glass Breakage Sensor Circuit  


DESCRIPTION

When the glass breakage sensor detects that the back door glass, quarter window assembly LH* or quarter window assembly RH* is broken, the sensor sounds the alarm for 30 seconds.

*: for 5 Door


WIRING DIAGRAM

B450008E01
1.302,0.552 1.917,0.75 0.615,0.198 10 false SSR+ 1.302,1.104 1.917,1.302 0.615,0.198 10 false SSR- 5.083,0.552 5.698,0.75 0.615,0.198 10 false GPBS 1.323,2.802 1.938,3 0.615,0.198 10 false SSR- 1.302,2.25 1.917,2.448 0.615,0.198 10 false SSR+ 5.073,2.823 5.688,3.021 0.615,0.198 10 false SSR+ 5.698,2.813 5.854,3.01 0.156,0.198 10 false E 1.854,0.438 2.01,0.635 0.156,0.198 10 false 1 1.854,0.979 2.01,1.177 0.156,0.198 10 false 2 1.875,2.688 2.031,2.885 0.156,0.198 10 false 2 1.875,2.146 2.031,2.344 0.156,0.198 10 false 1 0.635,1.375 1.094,1.573 0.458,0.198 10 false R25 0.646,1.552 4.625,1.75 3.979,0.198 10 false Quarter Window Assembly LH 0.573,3.063 1.031,3.26 0.458,0.198 10 false Q20 0.573,3.219 4.552,3.417 3.979,0.198 10 false Quarter Window Assembly RH 0.052,0.031 2.073,0.271 2.021,0.24 12 false for 5 Door: 5.021,1.208 5.177,1.406 0.156,0.198 10 false A 5.021,1.396 6.667,1.75 1.646,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 4.74,0.427 5.052,0.625 0.313,0.198 10 false 19 4.865,3.083 5.177,3.281 0.313,0.198 10 false Y2 4.865,3.25 7.156,3.448 2.292,0.198 10 false Back Door Glass 5.979,2.698 6.135,2.896 0.156,0.198 10 false 1 4.813,2.688 4.969,2.885 0.156,0.198 10 false 3

B240860E01
5.048,1.646 6.707,1.993 1.659,0.347 10 Main Body ECU (Multiplex Network Body ECU) 5.058,1.469 5.339,1.665 0.281,0.197 10 A 4.845,0.431 5.037,0.586 0.192,0.155 10 19 2.304,0.432 2.496,0.587 0.192,0.155 10 3 5.14,0.536 5.574,0.691 0.433,0.155 10 GPBS 1.786,0.538 2.177,0.693 0.391,0.155 10 SSR+ 0.052,0.032 0.954,0.230 0.902,0.197 12 for 3 Door: 1.237,0.968 2.349,1.119 1.112,0.151 10 Back Door Glass 1.237,0.822 1.537,0.983 0.300,0.160 10 Y2 1.193,0.432 1.339,0.586 0.147,0.155 10 1 2.891,0.42 3.082,0.574 0.191,0.155 10 *1 2.891,1.301 3.082,1.456 0.191,0.155 10 *2 1.421,0.545 1.545,0.700 0.124,0.155 10 E 2.312,1.3 2.504,1.455 0.192,0.155 10 2 1.786,1.411 2.177,1.565 0.391,0.155 10 SSR+ 1.237,1.815 2.349,1.973 1.112,0.158 10 Back Door Glass 0.257,2.098 2.491,2.266 2.234,0.167 10 *1: w/ Glass Hatch Opener System 0.257,2.396 2.550,2.553 2.292,0.157 10 *2: w/o Glass Hatch Opener System 1.231,1.679 1.531,1.829 0.300,0.150 10 X8 1.201,1.306 1.347,1.461 0.147,0.155 10 1 1.421,1.417 1.545,1.572 0.124,0.155 10 E

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (GLASS BREAKAGE SENSOR)
a.

Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sealed Glas Brak Sen Glass breakage sensor detection / With or Without With: Glass breakage sensor operating
Without: Glass breakage sensor not operating
-

OK:

"With" (glass breakage sensor operating) appears on screen.


Result
Result Proceed to
OK A
NG (for 5 Door) B
NG (for 3 Door) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)

C

6.INSPECT BACK DOOR GLASS (GLASS BREAKAGE SENSOR)
2.INSPECT QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)
a.
B240861E02
1.917,1.229 2.229,0.917 2.229,0.917 2.354,0.917 false 1.521,1.229 1.208,0.917 1.208,0.917 1.083,0.917 false 2.396,0.813 2.823,1.021 0.427,0.208 10 false SSR+ 0.688,0.813 1.073,0.979 0.385,0.167 10 false SSR-

Disconnect the R25 sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 2 (SSR-) Always Below 3.5 Ω




OK

3.INSPECT QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)

NG

REPLACE QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)

3.INSPECT QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)
a.
B240861E02
1.917,1.229 2.229,0.917 2.229,0.917 2.354,0.917 false 1.521,1.229 1.208,0.917 1.208,0.917 1.083,0.917 false 2.396,0.813 2.823,1.021 0.427,0.208 10 false SSR+ 0.688,0.813 1.073,0.979 0.385,0.167 10 false SSR-

Disconnect the Q20 sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 2 (SSR-) Always Below 3.5 Ω




OK

4.INSPECT BACK DOOR GLASS (GLASS BREAKAGE SENSOR)

NG

REPLACE QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)

4.INSPECT BACK DOOR GLASS (GLASS BREAKAGE SENSOR)
a.
B240863E01
0.257,0.647 0.678,0.806 0.422,0.160 10 SSR+ 2.732,0.647 2.877,0.806 0.145,0.160 10 E 2.193,1.074 2.541,0.731 2.541,0.731 2.676,0.731 false 1.259,1.074 0.911,0.731 0.911,0.731 0.776,0.731 false

Disconnect the Y2 sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SSR+) - 1 (E) Always Below 70 Ω




OK

5.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE BACK DOOR GLASS (GLASS BREAKAGE SENSOR)

5.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the R25, Q20 and Y2 sensor connectors.


b.

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R25-1 (SSR+) - A-19 (GPBS) Always Below 1 Ω
Q20-1 (SSR+) - R25-2 (SSR-) Always Below 1 Ω
Y2-3 (SSR+) - Q20-2 (SSR-) Always Below 1 Ω
R25-1 (SSR+) or A-19 (GPBS) - Body ground Always 10 kΩ or higher
Q20-1 (SSR+) or R25-2 (SSR-) - Body ground Always 10 kΩ or higher
Y2-3 (SSR+) or Q20-2 (SSR-) - Body ground Always 10 kΩ or higher
Y2-1 (E) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BACK DOOR GLASS (GLASS BREAKAGE SENSOR)
a.
B240863E01
0.257,0.647 0.678,0.806 0.422,0.160 10 SSR+ 2.732,0.647 2.877,0.806 0.145,0.160 10 E 2.193,1.074 2.541,0.731 2.541,0.731 2.676,0.731 false 1.259,1.074 0.911,0.731 0.911,0.731 0.776,0.731 false

w/ Glass Hatch Opener System:

i.

Disconnect the Y2 sensor connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SSR+) - 1 (E) Always Below 70 Ω




b.
B240862E01
0.8,1.793 1.210,1.957 0.411,0.163 10 SSR+ 2.213,1.799 2.337,1.963 0.124,0.163 10 E 1.287,1.885 1.441,1.885 1.441,1.885 1.547,1.472 false 2.166,1.885 2.012,1.885 2.012,1.885 1.906,1.472 false

w/o Glass Hatch Opener System:

i.

Disconnect the X8 sensor connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SSR+) - 1 (E) Always Below 70 Ω


Result
Result Proceed to
OK A
NG (w/ Glass Hatch Opener System) B
NG (w/o Glass Hatch Opener System) C




A

7.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR - MAIN BODY ECU AND BODY GROUND)

B

REPLACE BACK DOOR GLASS (GLASS BREAKAGE SENSOR)

C

REPLACE BACK DOOR GLASS (GLASS BREAKAGE SENSOR)

7.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR - MAIN BODY ECU AND BODY GROUND)
a.

w/ Glass Hatch Opener System:

i.

Disconnect the Y2 sensor connector.


ii.

Remove the main body ECU (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

Standard Resistance:
Tester Connection Condition Specified Condition
Y2-3 (SSR+) - A-19 (GPBS) Always Below 1 Ω
Y2-3 (SSR+) or A-19 (GPBS) - Body ground Always 10 kΩ or higher
Y2-1 (E) - Body ground Always Below 1 Ω




b.

w/o Glass Hatch Opener System:

i.

Disconnect the X8 sensor connector.


ii.

Remove the main body ECU (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

Standard Resistance:
Tester Connection Condition Specified Condition
X8-2 (SSR+) - A-19 (GPBS) Always Below 1 Ω
X8-2 (SSR+) or A-19 (GPBS) - Body ground Always 10 kΩ or higher
X8-1 (E) - Body ground Always Below 1 Ω





OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR