Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the center airbag sensor, spiral cable and steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.


DTC Code DTC Detection Condition Trouble Area
B1800/51 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the driver side squib circuit during the primary check.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1801/51 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal in the driver side squib circuit for 2 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1802/51 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1803/51 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

U148201E01
2.124,1.582 2.349,1.738 0.225,0.156 10 D+ 2.159,2.422 2.335,2.578 0.177,0.156 10 D- 4.892,1.664 5.117,1.820 0.225,0.156 10 D+ 4.892,2.505 5.069,2.660 0.177,0.156 10 D- 3.232,1.57 3.457,1.761 0.225,0.191 10 1 3.232,2.418 3.408,2.609 0.177,0.191 10 2 2.475,2.995 2.826,3.158 0.350,0.163 10 G41 0.794,2.995 1.144,3.158 0.350,0.163 10 z5 2.475,3.15 3.284,3.320 0.809,0.170 10 Spiral Cable 0.78,3.17 1.950,3.340 1.170,0.170 10 Driver Side Squib 4.591,1.552 4.754,1.791 0.163,0.239 10 5 4.591,2.385 4.830,2.611 0.239,0.225 10 6 4.808,4.165 5.096,4.307 0.288,0.142 10 G1 4.808,4.327 6.186,4.497 1.378,0.170 10 Center Airbag Sensor 2.475,2.428 2.701,2.618 0.225,0.191 10 1 2.475,1.58 2.652,1.771 0.177,0.191 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When installing the spiral cable and steering wheel, be sure to adjust the spiral cable as it may break if the steering wheel is turned before adjusting the spiral cable (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB)
a.
U148411E01
0.129,1.074 0.313,1.248 0.184,0.174 10 *1 0.793,1.071 0.968,1.250 0.175,0.179 10 *2 1.61,1.37 1.794,1.545 0.184,0.174 10 *a 2.19,1.392 2.364,1.571 0.175,0.179 10 *3 2.486,2.438 2.661,2.617 0.175,0.179 10 *5 2.262,3.024 2.445,3.199 0.184,0.174 10 *b 2.67,1.84 2.845,2.019 0.175,0.179 10 *4 0.487,2.07 0.679,2.240 0.192,0.170 10 z5 2.383,0.486 2.513,0.665 0.130,0.179 10 A 1.824,0.743 1.954,0.922 0.130,0.179 10 C 1.704,0.743 1.833,0.922 0.130,0.179 10 D 0.555,0.743 0.685,0.922 0.130,0.179 10 E 0.318,0.743 0.448,0.922 0.130,0.179 10 F 2.068,2.273 2.45,2.492 false 0.227,0.636 0.228,1.032 false 1.849,2.724 2.228,3.09 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the steering pad.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector E
*5 SST
*a Front view of wire harness connector
(to Driver Side Squib)
*b Color: Orange



OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.
C213963E02
2.445,0.666 2.587,0.836 0.142,0.170 10 A 2.081,0.938 2.229,1.113 0.148,0.175 10 B 1.749,0.941 1.891,1.111 0.142,0.170 10 C 1.612,0.941 1.754,1.111 0.142,0.170 10 D 0.598,0.941 0.740,1.111 0.142,0.170 10 E 0.4,0.941 0.542,1.111 0.142,0.170 10 F 0.847,1.208 1.003,1.384 0.156,0.177 10 *2 0.211,0.49 0.367,0.667 0.156,0.177 10 *1 2.299,1.538 2.455,1.715 0.156,0.177 10 *3

Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor



OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
U148412E01
0.112,1.056 0.296,1.231 0.184,0.174 10 *1 0.776,1.054 0.951,1.233 0.175,0.179 10 *2 1.576,1.508 1.759,1.682 0.184,0.174 10 *a 2.419,1.38 2.594,1.559 0.175,0.179 10 *3 2.262,3.024 2.445,3.199 0.184,0.174 10 *b 2.636,1.978 2.810,2.157 0.175,0.179 10 *4 0.461,2.208 0.653,2.377 0.192,0.170 10 z5 2.572,0.469 2.702,0.648 0.130,0.179 10 A 1.807,0.726 1.936,0.905 0.130,0.179 10 C 2.202,0.726 2.332,0.905 0.130,0.179 10 B 1.687,0.726 1.816,0.905 0.130,0.179 10 D 0.538,0.726 0.668,0.905 0.130,0.179 10 E 0.325,0.726 0.455,0.905 0.130,0.179 10 F 0.21,0.619 0.211,1.015 false 1.849,2.724 2.228,3.09 false 0.951,2.505 1.201,2.654 0.251,0.149 10 D- 2.2,2.514 2.509,2.663 0.309,0.149 10 D+ 1.638,2.104 1.174,2.585 false 1.74,2.104 2.163,2.585 false

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z5-2 (D+) - Body ground Ignition switch ON Below 1 V
z5-1 (D-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always 1 MΩ or higher
z5-2 (D+) - Body ground Always 1 MΩ or higher
z5-1 (D-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector E
*a Front view of wire harness connector
(to Driver Side Squib)
*b Color: Orange


OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
4.CHECK CENTER AIRBAG SENSOR
a.
C215879E09
0.281,0.896 0.438,1.094 0.156,0.198 10 false *1 0.844,1.229 1,1.427 0.156,0.198 10 false *2 2.167,1.594 2.323,1.792 0.156,0.198 10 false *3 1.813,0.969 1.958,1.135 0.146,0.167 10 false C 1.656,0.969 1.802,1.135 0.146,0.167 10 false D 0.625,0.99 0.771,1.156 0.146,0.167 10 false E 0.469,0.99 0.615,1.156 0.146,0.167 10 false F

Connect the connectors to the steering pad and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor



OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
a.
U148414E01
1.788,0.409 1.971,0.584 0.184,0.174 10 *1 0.759,1.171 0.934,1.350 0.175,0.179 10 *2 1.576,1.539 1.759,1.714 0.184,0.174 10 *a 2.161,1.429 2.336,1.608 0.175,0.179 10 *3 2.636,2.009 2.810,2.188 0.175,0.179 10 *4 0.445,2.239 0.739,2.409 0.293,0.170 10 G41 2.349,0.587 2.478,0.766 0.130,0.179 10 A 1.664,0.843 1.793,1.022 0.130,0.179 10 C 1.99,0.843 2.120,1.022 0.130,0.179 10 B 1.475,0.843 1.604,1.022 0.130,0.179 10 D 0.442,0.843 0.571,1.022 0.130,0.179 10 E 0.249,0.843 0.379,1.022 0.130,0.179 10 F 2.349,2.792 2.632,2.941 0.283,0.149 10 D+ 1.04,2.818 1.296,2.967 0.255,0.149 10 D- 1.708,2.391 1.244,2.872 false 1.89,2.391 2.312,2.872 false

Restore the released activation prevention mechanism of connector B to its original condition.


b.

Disconnect the instrument panel wire connector from the spiral cable.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G41-1 (D+) - Body ground Ignition switch ON Below 1 V
G41-2 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-1 (D+) - G41-2 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-1 (D+) - G41-2 (D-) Always 1 MΩ or higher
G41-1 (D+) - Body ground Always 1 MΩ or higher
G41-2 (D-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Instrument Panel Wire
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector C
*a Rear view of wire harness connector
(to Spiral Cable)


OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE