Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

The skid control ECU outputs a stop light operation signal to the stop light control ECU. When the skid control ECU detects a malfunction in the stop light circuit, the driving support ECU outputs DTC C1A4B.

DTC Code DTC Detection Condition Trouble Area
C1A4B
·

For the pre-crash safety system:

-

The engine switch is on (IG).



·

For the radar cruise control system:

-

The vehicle is being driven at 50 km/h (31 mph) or more and the ACC main switch is ON.



When the skid control ECU detects a malfunction* in the stop light control ECU circuit, the skid control ECU sends a malfunction warning signal via CAN to the driving support ECU and a DTC is output.
*: Condition for skid control ECU malfunction warning signal output. When the voltage at the IG1 terminal is between 11 and 14 V and the stop light illumination output (STP0) is ON, there is no input signal to the STP2 terminal for 5 seconds or more, or when the input signals to terminals STP and STP2 are different for 5 seconds or more when the voltage at the IG1 terminal is between 11 and 14 V and the stop light illumination output (STP0) is OFF.
·

Lighting system

·

Harness or connector

·

Stop light control ECU

·

Driving support ECU



WIRING DIAGRAM

E260400E01
1.775,3.937 2.241,4.184 0.466,0.247 10 1 0.644,3.955 1.110,4.202 0.466,0.247 10 2 0.745,0.582 1.211,0.829 0.466,0.247 10 1 1.33,0.578 1.519,0.738 0.188,0.160 10 2 2.241,0.611 2.429,0.771 0.188,0.160 10 6 2.241,1.573 2.429,1.733 0.188,0.160 10 8 4.784,1.573 4.972,1.733 0.188,0.160 10 9 4.784,1.986 4.972,2.146 0.188,0.160 10 4 5.835,1.573 6.203,1.733 0.369,0.160 10 16 5.835,1.986 6.203,2.146 0.369,0.160 10 42 5.835,2.925 6.203,3.085 0.369,0.160 10 45 5.912,3.941 6.281,4.101 0.369,0.160 10 7 2.241,2.526 2.429,2.686 0.188,0.160 10 5 2.444,0.611 2.862,0.771 0.417,0.160 10 +B 2.444,1.573 2.862,1.733 0.417,0.160 10 GND 2.444,2.526 2.862,2.686 0.417,0.160 10 STP 4.357,1.573 4.774,1.733 0.417,0.160 10 ACC 4.357,2.021 4.774,2.181 0.417,0.160 10 ESSI 4.77,2.939 4.958,3.099 0.188,0.160 10 1 4.357,2.932 4.774,3.092 0.417,0.160 10 OUT 6.171,1.674 6.588,1.835 0.417,0.160 10 STP0 6.171,2.091 6.588,2.252 0.417,0.160 10 EX0* 6.171,3.023 6.588,3.183 0.417,0.160 10 STP2 6.171,4.06 6.588,4.220 0.417,0.160 10 STP 5.372,5.846 5.790,6.006 0.417,0.160 10 A7 0.854,1.056 1.320,1.210 0.466,0.155 10 A59 0.854,1.2 1.616,1.355 0.762,0.155 10 Diode 0.658,2.303 1.420,2.457 0.762,0.155 10 STOP 0.98,3.241 1.900,3.396 0.920,0.155 10 from Battery 0.807,4.348 1.727,4.503 0.920,0.155 10 A5 0.807,4.497 2.116,4.652 1.309,0.155 10 Stop Light Switch 5.371,6.003 7.036,6.477 1.665,0.474 10 Master Cylinder Solenoid (Skid Control ECU) 2.685,3.395 3.065,3.564 0.380,0.168 10 A54 2.671,3.559 4.611,3.713 1.941,0.155 10 Stop Light Control ECU 3.621,4.444 4.643,4.601 1.022,0.157 10 to Stop Lights 0.345,5.948 2.667,6.102 2.323,0.155 10 *: Emergency Brake Signal 0.898,6.368 3.221,6.522 2.323,0.155 10 : CAN Communication Line 4.027,5.026 4.434,5.187 0.407,0.160 10 CA2H 3.441,5.721 4.361,5.876 0.920,0.155 10 G119 3.441,5.871 4.750,6.025 1.309,0.155 10 Driving Support ECU 6.157,5.012 6.574,5.173 0.417,0.160 10 CANH 6.157,5.419 6.574,5.579 0.417,0.160 10 CANL 4.539,4.865 4.908,5.026 0.369,0.160 10 39 4.539,5.3 4.908,5.460 0.369,0.160 10 17 5.842,4.865 6.023,5.026 0.181,0.160 10 11 5.842,5.3 6.023,5.460 0.181,0.160 10 25 4.054,5.447 4.434,5.607 0.380,0.160 10 CA2L

CAUTION / NOTICE / HINT

NOTICE:
·
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the driving support ECU, always replace it with a new one and be sure to perform initialization (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>INSTALLATION). If an ECU which was installed to another vehicle is used, the information stored in the ECU will not match the information from the vehicle, and as a result, a DTC may be stored.



HINT:
·

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C1425).

·

This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more DTCs in the CAN communication system are output.



PROCEDURE

1.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

OK:

Vehicle stability control system DTCs are not output.




OK

2.CHECK STOP LIGHT OPERATION

NG

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off




OK

3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

NG

7.CHECK TERMINAL VOLTAGE AND RESISTANCE (+B, GND)
3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch condition observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.




OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)

NG

10.CHECK TERMINAL VOLTAGE (STP)
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light control ECU ECU ON/OFF Observe the stop lights (do not come on for 2 to 5 seconds).


f.

While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control ECU output/ ON or OFF ON: Stop light control ECU on (Stop lights on)
OFF: Stop light control ECU off (Stop lights off)
-


Result
Result Proceed to
When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off A
When Active Test performed, Data List item changes between ON and OFF, but stop lights do not turn on B


A

5.CHECK TERMINAL VOLTAGE (STP2)

B

11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL ECU)
5.CHECK TERMINAL VOLTAGE (STP2)
a.

Disconnect the A7 skid control ECU connector.


b.
U148398E01
1.022,0.617 1.224,0.780 0.202,0.163 10 A7 0.128,0.005 2.553,0.360 2.426,0.354 10 *a 2.539,1.538 2.539,1.873 false 2.346,1.886 2.748,2.049 0.402,0.163 10 STP2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

6.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.RECONFIRM DTC

b.

Start the engine.


c.

Perform a road test.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

7.CHECK TERMINAL VOLTAGE AND RESISTANCE (+B, GND)
a.

Disconnect the A54 stop light control ECU connector.


b.
U148288E01
0.077,0.03 0.266,0.199 0.189,0.170 10 *a 0.375,1.529 0.597,1.689 0.222,0.159 10 +B 1.286,1.207 0.504,1.392 0.504,1.392 0.504,1.478 false 2.728,1.535 3.060,1.709 0.332,0.174 10 GND 1.929,1.22 2.914,1.369 2.914,1.369 2.914,1.466 false 0.313,0.825 0.610,0.994 0.297,0.170 10 A54

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-6 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-8 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control ECU)



OK

8.CHECK TERMINAL VOLTAGE (STP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (STP)
a.

Disconnect the A54 stop light control ECU connector.


b.
U148289E01
0.077,0.048 0.266,0.218 0.189,0.170 10 *a 0.375,1.548 0.701,1.707 0.326,0.159 10 STP 1.047,1.242 0.504,1.41 0.504,1.41 0.504,1.496 false 0.48,0.644 0.761,0.807 0.281,0.163 10 A54

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-5 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control ECU)



OK

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL ECU - SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL ECU - SKID CONTROL ECU)
a.

Disconnect the A54 stop light control ECU connector.


b.

Disconnect the A7 skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-1 (OUT) - A7-45 (STP2) Always Below 1 Ω
A54-1 (OUT) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TERMINAL VOLTAGE (STP)
a.

Disconnect the A7 skid control ECU connector.


b.
U148399E01
0.31,0.712 0.584,0.874 0.274,0.163 10 A7 0.128,0.038 2.553,0.393 2.426,0.354 10 *a 2.509,0.565 2.859,0.742 0.350,0.177 10 STP 1.684,1.133 2.457,0.677 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL ECU)
a.

Disconnect the A7 skid control ECU connector.


b.

Disconnect the A54 stop light control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-16 (STP0) - A54-9 (ACC) Always Below 1 Ω
A7-16 (STP0) - Body ground Always 10 kΩ or higher




OK

12.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL ECU)
a.

Disconnect the A7 skid control ECU connector.


b.

Disconnect the A54 stop light control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-45 (STP2) - A54-1 (OUT) Always Below 1 Ω
A7-45 (STP2) - Body ground Always 10 kΩ or higher




OK

13.REPLACE STOP LIGHT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE STOP LIGHT CONTROL ECU
a.

Temporally replace the stop light control ECU with a new or normally function one (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT CONTROL RELAY>REMOVAL).



NEXT

14.CHECK FOR DTC (PRE-CRASH SAFETY SYSTEM)
14.CHECK FOR DTC (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

HINT:

If the detection conditions are not met, the system cannot detect malfunctions.

·

Pre-crash safety system:

(a)

Turn the ignition switch off.

(b)

Connect the intelligent tester to the DLC3.

(c)

Turn the ignition switch to ON.

(d)

Turn the intelligent tester on.

(e)

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay STOP light control ECU ECU ON/OFF Observe the stop lights (do not come on for 2 to 5 seconds).

(f)

While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output STOP light control ECU output/ ON or OFF ON: Stop light control ECU output on (Stop lights on)
OFF: Stop light control ECU output off (Stop lights off)
-





b.

Make sure the following conditions are met:

·

Radar cruise control system:

The vehicle is being driven at a speed of approximately 50 km/h (31 mph) or more and the distance control switch is on.






OK

END

NG