Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)
82168
2.INSTALL NO. 2 SEAT WIRE (for Driver Side)
Attach the 2 clamps to install the seat wire.
Connect the connector.
71552S
3.INSTALL SEPARATE TYPE FRONT SEATBACK PAD
Install the seatback pad.
87510N
4.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
71074S
5.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
The number of hog rings differs according to seat type.
| *A | for Type A | *B | for Type B |
| *1 | Hog Ring Pliers | - | - |
Attach the 4 claws to install the 2 headrest supports.
w/ Front Seat Side Airbag:
Connect the seatback cover bracket to the seatback pad.
Install the seatback cover bracket to the seat frame with the nut.
After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
Close the 2 fasteners, and then close the seatback cover.
| *A | for Cloth Seat | *B | for Leather Seat |
Using hog ring pliers, install 3 new hog rings.
| *1 | Hog Ring Pliers |
71876A
6.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Move the cover in the direction of the arrow to install the cover.
Attach the guide.
71875A
7.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure described for the LH side.
82192
8.INSTALL FRONT SEAT WIRE LH
Install the seat wire.
87501B
9.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)
71537D
10.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
Move the protector in the direction of the arrow to attach the hook and install the protector.
Install the screw.
71537C
11.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Use the same procedure described for the LH side.
71874
12.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
Attach the hook and clip to install the cushion shield.
Install the screw.
71873
13.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
Attach the hook and clip to install the cushion shield.
Install the screw.
71876
14.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Attach the claw and guide to install the cover.
87510L
15.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
71072S
16.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Type A:
Using hog ring pliers, connect the straps with new hog rings.
| *1 | Hog Ring Pliers |
Type B:
Connect the straps with new tack pins.
| *1 | Tack Pin |
17.INSTALL SEAT CUSHION COVER WITH PAD
Install the seat cushion cover with pad.
for Front Passenger Side:
Attach the claw to connect the connector.
Attach the hooks.
w/ Seat Heater System:
Connect the seat heater connector and attach the 3 wire harness clamps.
71149A
18.INSTALL FRONT SEAT LEG COVER LH
Move the cover in the direction of the arrow to install the cover.
Attach the 2 claws.
62476E
19.INSTALL CAP
Install the 2 caps.
71440S
20.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Install the seatback assembly with the 4 bolts.
w/ Front Seat Side Airbag:
Connect the airbag wire harness.
Attach the fastening tape to close the cover.
Attach the 3 airbag wire harness clamps.
Attach the claw and connect the airbag connector.
for Clip Type:
Install the 2 clips.
for Hook Type:
Attach the 2 hooks.
w/ Seat Heater System:
Connect the seat heater connector and attach the wire harness clamp.
for Driver Side:
Attach the clamp to connect the No. 2 seat wire.
Install the rubber band to the seat cushion spring.
73240
21.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
for Driver Side:
(See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSTALLATION)
for Front Passenger Side:
(See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSTALLATION)
71862
22.INSTALL FRONT SEAT INNER CUSHION SHIELD LH
Attach the 3 claws to install the cushion shield.
71861
23.INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
Attach the 4 claws to install the cushion shield.
84920
24.INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side)
71812D
25.INSTALL FRONT SEAT CUSHION SHIELD LH
for Driver Side:
Attach the 5 wire harness clamps and connect the 2 connectors.
Attach the 4 claws and clip to install the cushion shield.
Install the screw.
72495
26.INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)
Install the handle with the screw.
72526
27.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
Attach the claw to install the handle.