Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
55330B
1.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Attach the 2 claws to install the instrument panel reinforcement assembly.
Install the 5 bolts.
2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY
Install the instrument panel reinforcement assembly with air conditioning unit assembly.
Install the bolts and nuts and instrument panel reinforcement assembly with air conditioning unit assembly.
Using a 8 mm hexagon wrench, tighten the 2 collars.
Using a T40 "TORX" socket, install the 5 "TORX" bolts.
Install the 5 caps.
Attach the clamps and connectors to the wire harness.
Install the bolts and nuts.
87201
3.INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY
Attach the 3 claws to install the No. 1 air duct sub-assembly.
87201B
4.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
Attach the 2 claws to install the No. 2 air duct sub-assembly.
Install the screw.
55347A
5.INSTALL NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET LH
Install the No. 1 instrument panel brace mounting bracket LH with the 2 nuts and bolt.
55347A
6.INSTALL NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET RH
Install the No. 1 instrument panel brace mounting bracket RH with the 2 nuts and bolt.
58861B
7.INSTALL NO. 1 CONSOLE BOX DUCT
Install the No. 1 console box duct with the clip.
87212G
8.INSTALL REAR NO. 3 AIR DUCT
Attach the 6 claws and 3 clamps to install the rear No. 3 air duct.
87212
9.INSTALL REAR NO. 1 AIR DUCT
Attach the 6 claws and 3 clamps to install the rear No. 1 air duct.
58510D
10.INSTALL FRONT CARPET ASSEMBLY
Install the front floor carpet assembly.
11.INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat:
Install the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION).
for Power Seat:
Install the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION).
for Walk in Seat Type:
Install the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>INSTALLATION).
for Bench Seat Type:
Install the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>INSTALLATION).
12.INSTALL FRONT SEAT ASSEMBLY RH
for Manual Seat:
Install the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION).
for Power Seat:
Install the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION).
for Walk in Seat Type:
Install the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>INSTALLATION).
for Bench Seat Type:
Install the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>INSTALLATION).
45250
13.INSTALL STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
Install the steering column assembly (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>INSTALLATION).
for Power Tilt and Power Telescopic Steering Column:
Install the steering column assembly (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>INSTALLATION).
14.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
Install the instrument panel sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION).
85110
15.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
Install the windshield wiper motor assembly (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).
87245A
16.CONNECT HEATER WATER INLET HOSE AND OUTLET HOSE
Connect the 2 heater water hose.
Using pliers, grip the claws of the clips and slide the 2 clips.
| *A | for 1GR-FE, for Single Air Conditioning System | *B | for 1KD-FTV, for Single Air Conditioning System |
| *C | for 5L-E, for Single Air Conditioning System | *D | for 2TR-FE, for Single Air Conditioning System |
| *E | for 1GR-FE, for Dual Air Conditioning System | *F | for 1KD-FTV, Dual Air Conditioning System |
| *G | for 5L-E, Dual Air Conditioning System | *H | for 2TR-FE, Dual Air Conditioning System |
| *I | for Dual Air Conditioning System, for LHD | *J | for Dual Air Conditioning System, for RHD |
| *K | for 1GD-FTV, for Single Air Conditioning System | *L | for 1GD-FTV, for Dual Air Conditioning System |
| *M | for 1GD-FTV, for Single Air Conditioning System
w/ Combustion Type Power Heater |
*N | for 1GD-FTV, for Dual Air Conditioning System
w/ Combustion Type Power Heater |
| *a | Green Marking | *b | Blue Marking |
| *c | Orange Marking | *d | Yellow Marking |
| *e | White Marking | *f | Pink Marking |
| *g | Red Marking | *h | Purple Marking |
88710E
17.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for Bolt Joint Type)
Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the air conditioning tube and accessory assembly.
ND-OIL 8 or equivalent
Install the 2 O-rings to the air conditioning tube and accessory assembly.
Connect the air conditioning tube and accessory assembly.
Install the 2 bolts.
88710E
18.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for Quick Joint Type)
Install the grommet.
Install the 2 O-rings to the air conditioning tube and accessory assembly.
Connect the air conditioning tube and accessory assembly with the piping clamp.
ND-OIL 8 or equivalent
| *a | CORRECT |
| *b | INCORRECT |
After the connection, check that the claw of the piping clamp is attached.
19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
20.CHARGE REFRIGERANT
21.ADD ENGINE COOLANT
for 1GR-FE:
Add engine coolant (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLANT>REPLACEMENT).
for 2TR-FE:
Add engine coolant (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLANT>REPLACEMENT).
for 1KD-FTV:
Add engine coolant (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLANT>REPLACEMENT).
for 5L-E:
Add engine coolant (See page Engine / Hybrid System>5L-E (COOLING)>COOLANT>REPLACEMENT).
for 1GD-FTV:
Add engine coolant (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).
22. WARM UP ENGINE
23.INSPECT FOR COOLANT LEAK
for 1GR-FE:
Inspect for coolant leak (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).
for 2TR-FE:
Inspect for coolant leak (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).
for 1KD-FTV:
Inspect for coolant leak (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).
for 5L-E:
Inspect for coolant leak (See page Engine / Hybrid System>5L-E (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).
for 1GD-FTV:
Inspect for coolant leak (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).
24.CHECK FOR REFRIGERANT GAS LEAK
53292A
25.INSTALL UPPER RADIATOR SUPPORT SEAL
26.CHECK SRS WARNING LIGHT
Check the SRS warning light (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).