Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
55401E
1.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
for LHD:
Attach the 2 guides to install the instrument panel safety pad sub-assembly.
Install the 2 brackets with the 4 bolts and 2 nuts.
Connect the connectors and attach the clamps and claws.
Install the 2 passenger airbag bolts <G>.
Install the 6 bolts <E> and nut <F>.
Install the front floor carpet.
| *1 | Bolt <E> | *2 | Nut <F> |
| *3 | Bolt <G> | *4 | Guide |
| *5 | Bracket | - | - |
for RHD:
Attach the 2 guides to install the instrument panel safety pad sub-assembly.
Install the 2 brackets with the 4 bolts and 2 nuts.
Connect the connectors and attach the clamps and claws.
Install the 2 passenger airbag bolts <G>.
Install the 6 bolts <E> and nut <F>.
Install the front floor carpet.
| *1 | Bolt <E> | *2 | Nut <F> |
| *3 | Bolt <G> | *4 | Guide |
| *5 | Bracket | - | - |
86160P
2.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
55408F
3.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Attach the 2 clips, claw and 2 guides to install the No. 1 instrument panel speaker panel.
55409F
4.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Use the same procedure described for the No. 1 instrument panel speaker panel.
55650
5.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Attach the 4 clips to install the No. 1 instrument panel register.
55660
6.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Use the same procedure described for the No. 1 instrument panel register.
86160L
7.INSTALL FRONT NO. 4 SPEAKER ASSEMBLY
55421B
8.INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL
Attach the 8 clips and 2 guides to install the upper instrument cluster finish panel.
55406B
9.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o CRAWL)
Attach the 3 clips and guide to install the lower center instrument cluster finish panel.
Install the 2 bolts <E>.
55936E
10.INSTALL CENTER CLUSTER MODULE SWITCH (w/ CRAWL)
55522B
11.INSTALL RADIO TUNER OPENING COVER (w/o Audio)
Install the radio tuner opening cover with the 4 bolts.
86120
12.INSTALL RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)
86431
13.INSTALL DISPLAY AND NAVIGATION MODULE DISPLAY (w/ Navigation System)
55420A
14.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Navigation System)
Connect each connector.
Attach the 10 clips to install the center instrument cluster finish panel.
89533
15.INSTALL 4 WHEEL DRIVE CONTROL ECU
859A1
16.INSTALL DRIVING SUPPORT SWITCH CONTROL ECU
55550
17.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
Connect each connector.
Attach the 5 clips and claw to install the glove compartment door.
Install the 2 bolts <C> and 2 screws <A> or <B>.
| *1 | Bolt |
| *2 | Screw |
55461A
18.INSTALL INSTRUMENT PANEL ORNAMENT
Attach the 5 clips to install the instrument panel ornament.
55317A
19.INSTALL INSTRUMENT SIDE PANEL RH
Connect the connector.
Attach the 5 clips, claw and 3 guides to install the instrument side panel.
83100
20.INSTALL COMBINATION METER ASSEMBLY
55404D
21.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Attach the 4 claws, 2 clips and 2 guides to install the instrument cluster finish panel.
73900
22.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
55045
23.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Connect each connector and each cable.
w/o Knee Airbag:
Attach the 7 clips to install the lower instrument panel finish panel.
w/ Knee Airbag:
Attach the 14 clips to install the lower instrument panel finish panel.
Install the 2 bolts <C>.
Attach the 2 claws to close the cover.
55480D
24.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Connect each connector.
Attach the 4 clips to install the instrument panel finish panel.
55476C
25.INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)
Connect each connector.
Attach the 4 clips to install the instrument panel finish plate garnish.
55471A
26.INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)
Attach the 3 clips to install the instrument cluster finish panel ornament.
55318C
27.INSTALL INSTRUMENT SIDE PANEL LH
Attach the 5 clips, claw and 3 guides to install the instrument side panel.
86160J
28.INSTALL FRONT NO. 3 SPEAKER ASSEMBLY
62212
29.INSTALL FRONT PILLAR GARNISH LH
62211
30.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
74611F
31.INSTALL NO. 1 ASSIST GRIP
74616C
32.INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH
74615E
33.INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH
Use the same procedure described for the LH side.
62312B
34.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
35.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62112
36.INSTALL COWL SIDE TRIM BOARD LH
62111C
37.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
67920
38.INSTALL DOOR SCUFF PLATE ASSEMBLY LH
67910
39.INSTALL DOOR SCUFF PLATE ASSEMBLY RH
Use the same procedure described for the LH side.
58910C
40.INSTALL REAR CONSOLE BOX ASSEMBLY
for Automatic Transmission:
Install the rear console box assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Automatic Transmission)>REMOVAL).
for Manual Transmission:
Install the rear console box assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Manual Transmission)>REMOVAL).
w/ Refrigerated Cool Box:
Install the rear console box assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX (w/ Refrigerated Cool Box)>INSTALLATION).
for Bench Seat Type:
Install the rear console box assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Bench Seat Type)>INSTALLATION).
58191
41.INSTALL FRONT FLOOR FOOTREST
for LHD:
Install the front floor footrest (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT FLOOR FOOTREST>INSTALLATION).
for RHD:
Install the front floor footrest (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT FLOOR FOOTREST>INSTALLATION).
42.INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat:
Install the front seat assembly (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION).
for Power Seat:
Install the front seat assembly (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION).
43.INSTALL FRONT SEAT ASSEMBLY RH
for Manual Seat:
Use the same procedure described for the LH side.
for Power Seat:
Use the same procedure described for the LH side.
for Walk in Seat Type:
Install the front seat assembly (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>INSTALLATION).
84140
44.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
Install the headlight dimmer switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSTALLATION).
45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
46.CHECK SRS WARNING LIGHT
Check the SRS warning light (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).