Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR AIR CONDITIONING UNIT › 2015.06–2016.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261176 REAR AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  REAR AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 88566R 1.INSTALL REAR ROOF NO. 1 AIR DUCT

a.

Install the duct with the 4 clips.


Hide 88566S 2.INSTALL REAR ROOF NO. 2 AIR DUCT

a.

Install the duct with the clip.


Hide 88566T 3.INSTALL REAR ROOF NO. 3 AIR DUCT

a.

Install the duct with the clip.


Hide 88566U 4.INSTALL REAR ROOF NO. 4 AIR DUCT

a.

Install the duct with the clip.


Hide 88566V 5.INSTALL REAR ROOF NO. 5 AIR DUCT

a.

Install the duct with the clip.


Hide 87030A 6.INSTALL REAR COOLING UNIT ASSEMBLY

a.

Install the rear cooling unit to the vehicle with the 5 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Connect the 3 connectors.


c.

Attach the 3 clamps.


Hide 87217D 7.INSTALL REAR ROOF NO. 1 AIR DUCT

a.

Insert the upper part of the duct into the roof side duct and, using that point as a pivot point, swing the duct into place and install it to the rear cooling unit.


b.

Attach the 2 claws to install the cooler plate.


Hide 87217F 8.INSTALL REAR SIDE NO. 3 AIR DUCT

a.

Install the duct with the 2 clips.


Hide 87217E 9.INSTALL REAR SIDE NO. 2 AIR DUCT

a.

Install the duct with the 2 clips and attach the clamp.


Hide 88710A 11.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the attached vinyl tape from the pipe.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the air conditioning tube and accessory assembly.


c.

Install the 2 O-rings to the air conditioning tube and accessory assembly.


d.

Connect the air conditioning tube and accessory assembly.


e.

Install the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


f.

Connect the heater water inlet hose and heater water outlet hose.


g.

Using pliers, grip the claws of the clips and slide the 2 clips.


Hide 62630P 12.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH

Hide 74603C 14.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

Hide 74617A 15.INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

Hide 64712F 16.INSTALL FRONT DECK SIDE TRIM COVER RH (w/ Tonneau Cover)

Hide 64937A 17.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

Hide 64725D 18.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 73233A 19.INSTALL REAR NO. 1 LAP BELT OUTER ANCHOR COVER SEAT

Hide 58570C 20.INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

Hide 57411D 21.INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

Hide 57412C 22.INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)

Hide 58574A 23.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

Hide 58401A 24.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

Hide 64717A 25.INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

Hide 64910M 26.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 62331C 28.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

Hide 67933 30.INSTALL QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

Hide 58371F 31.INSTALL NO. 1 REAR FLOOR STEP COVER (w/ Rear No. 2 Seat)

Hide 32.INSTALL REAR NO. 1 SEATBACK ASSEMBLY

a.

for 60/40 Split Double-folding Seat Type LH Side:

Install the rear No. 1 seatback assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type LH Side)>INSTALLATION).


b.

for 60/40 Split Double-folding Seat Type RH Side:

Install the rear No. 1 seatback assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type RH Side)>INSTALLATION).


Hide 33.INSTALL REAR NO. 2 SEAT ASSEMBLY

a.

for Manual Seat:

Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side)>INSTALLATION).


b.

for Power Seat:

Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>INSTALLATION).


c.

for Face to Face Seat Type:

Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>INSTALLATION).


Hide 34.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 35.ADD ENGINE COOLANT

a.

for 1GR-FE:

Add engine coolant (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLANT>REPLACEMENT).


b.

for 2TR-FE:

Add engine coolant (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLANT>REPLACEMENT).


c.

for 1KD-FTV:

Add engine coolant (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLANT>REPLACEMENT).


d.

for 5L-E:

Add engine coolant (See page Engine / Hybrid System>5L-E (COOLING)>COOLANT>REPLACEMENT).


e.

for 1GD-FTV:

Add engine coolant (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).


Hide 38.INSPECT FOR ENGINE COOLANT LEAKS

a.

for 1GR-FE:

Check for engine coolant leaks (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLANT>REPLACEMENT).


b.

for 2TR-FE:

Check for engine coolant leaks (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLANT>REPLACEMENT).


c.

for 1KD-FTV:

Check for engine coolant leaks (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLANT>REPLACEMENT).


d.

for 5L-E:

Check for engine coolant leaks (See page Engine / Hybrid System>5L-E (COOLING)>COOLANT>REPLACEMENT).


e.

for 1GD-FTV:

Check for engine coolant leaks (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).


Hide 40.CHECK SRS WARNING LIGHT