1.INSTALL COOLER DRYER
Using pliers, install the cooler dryer.
Apply a sufficient amount of compressor oil to the contact surfaces of a new O-ring and the cap.
ND-OIL 8 or equivalent
Install the O-ring to the cap.
Using a 14 mm socket hexagon wrench, install the cap to the modulator.
88460
2.INSTALL COOLER CONDENSER ASSEMBLY
Install the cooler condenser assembly with the 3 bolts as shown in the illustration.
If the cooler condenser assembly is replaced with a new one, add compressor oil to the new cooler condenser assembly.
40 cc (1.35 fl.oz)
ND-OIL 8 or equivalent
88703
3.CONNECT DISCHARGE HOSE SUB-ASSEMBLY
Remove the attached vinyl tape from the hose and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly joint.
ND-OIL 8 or equivalent
Install the O-ring to the discharge hose sub-assembly.
Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.
When tightening the bolt, do not allow any tools to contact the pipe.
When tightening the bolt, hold a part of the pipe near the connector.
88463A
4.CONNECT NO. 2 COOLER CONDENSER BRACKET
Install the 2 bolts and No. 2 cooler condenser bracket.
88463
5.CONNECT NO. 1 COOLER CONDENSER BRACKET
Install the 2 bolts and No. 1 cooler condenser bracket.
88710
6.INSTALL AIR CONDITIONING TUBE ASSEMBLY
Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube assembly joint.
ND-OIL 8 or equivalent
Install the O-ring to the air conditioning tube assembly.
Connect the air conditioning tube assembly to the cooler condenser assembly with the bolt.
When tightening the bolt, do not allow any tools to contact the pipe.
When tightening the bolt, hold a part of the pipe near the connector.
7.CHARGE REFRIGERANT
16400
8.INSTALL RADIATOR ASSEMBLY
for 1GR-FE:
Install the radiator assembly (See page Engine / Hybrid System>1GR-FE (COOLING)>RADIATOR>INSTALLATION).
for 2TR-FE:
Install the radiator assembly (See page Engine / Hybrid System>2TR-FE (COOLING)>RADIATOR>INSTALLATION).
for 1KD-FTV:
Install the radiator assembly (See page Engine / Hybrid System>1KD-FTV (COOLING)>RADIATOR>INSTALLATION).
for 5L-E:
Install the radiator assembly (See page Engine / Hybrid System>5L-E (COOLING)>RADIATOR>INSTALLATION).
for 1GD-FTV:
Install the radiator assembly (See page Engine / Hybrid System>1GD-FTV (COOLING)>RADIATOR>INSTALLATION).
9.ADD ENGINE COOLANT
for 1GR-FE:
Add engine coolant (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLANT>REPLACEMENT).
for 2TR-FE:
Add engine coolant (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLANT>REPLACEMENT).
for 1KD-FTV:
Add engine coolant (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLANT>REPLACEMENT).
for 5L-E:
Add engine coolant (See page Engine / Hybrid System>5L-E (COOLING)>COOLANT>REPLACEMENT).
for 1GD-FTV:
Add engine coolant (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).
10. WARM UP ENGINE
11.INSPECT FOR ENGINE COOLANT LEAK
for 1GR-FE:
Inspect for engine coolant leak (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).
for 2TR-FE:
Inspect for engine coolant leak (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).
for 1KD-FTV:
Inspect for engine coolant leak (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).
for 5L-E:
Inspect for engine coolant leak (See page Engine / Hybrid System>5L-E (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).
for 1GD-FTV:
Inspect for engine coolant leak (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).
12.CHECK FOR REFRIGERANT GAS LEAK