Home › Vehicle Interior › HEATING / AIR CONDITIONING › VISCOUS HEATER MAGNET CLUTCH (for 1GD-FTV) › 2015.06–2018.06
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261202 VISCOUS HEATER MAGNET CLUTCH(for 1GD-FTV) A

HEATING / AIR CONDITIONING  VISCOUS HEATER MAGNET CLUTCH(for 1GD-FTV)  INSTALLATION  


PROCEDURE

Hide 87120G 1.INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY

E321815

a.

Temporarily install the viscous heater with magnet clutch assembly with the 2 bolts.


b.

Connect the connector.


Hide 2.CONNECT HEATER WATER INLET HOSE

E321816E02
1.563,3.01 0.958,3.01 true 1.302,1.479 1.417,1.76 true 1.417,1.76 1.833,1.76 true 0.792,2.302 1.125,2.521 0.333,0.219 10 false *a 0.802,2.927 1.135,3.146 0.333,0.219 10 false *b 1.604,2.438 1.938,2.656 0.333,0.219 10 false *c 1.854,1.667 2.188,1.885 0.333,0.219 10 false *d 1.198,0.594 1.354,0.771 0.156,0.177 10 false A

a.

Align the rib of the viscous heater with magnet clutch assembly with the marking (red). Connect the heater water inlet hose and install the clip within the range shown in the illustration.

NOTICE:

Do not apply excessive force to the heater water inlet hose.


Text in Illustration
*a View A
*b Paint Marking (Red)
*c Clip Installation Angle (40°)
*d Rib


Hide 3.CONNECT HEATER WATER OUTLET HOSE

E321817E02
1.583,2.969 0.938,2.969 true 1.052,1.344 1.323,1.698 true 1.323,1.698 1.865,1.698 true 0.802,2.271 1.083,2.49 0.281,0.219 10 false *a 0.781,2.875 1.063,3.094 0.281,0.219 10 false *b 1.615,2.375 1.896,2.594 0.281,0.219 10 false *c 1.885,1.615 2.167,1.833 0.281,0.219 10 false *d 1.427,0.719 1.677,0.979 0.25,0.26 10 false A

a.

Align the rib of the viscous heater with magnet clutch assembly with the marking (red). Connect the heater water outlet hose and install the clip within the range shown in the illustration.

NOTICE:

Do not apply excessive force to the heater water outlet hose.


Text in Illustration
*a View A
*b Paint Marking (Red)
*c Clip Installation Angle (40°)
*d Rib


b.

Install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88359 5.INSTALL VISCOUS HEATER V BELT

a.

Hide 87120G 6.TIGHTEN VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

E321818

a.

Tighten the 2 bolts.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 7.CONNECT OIL COOLER HOSE (for Automatic Transmission)

Hide 16470 8.INSTALL RADIATOR RESERVE TANK ASSEMBLY

Hide 17341K 9.INSTALL NO. 1 INTERCOOLER AIR HOSE

Hide 82123 13.INSTALL NO. 3 ENGINE WIRE (for Cold Area)

Hide 51405A 15.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Cold Area)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53292A 18.INSTALL UPPER RADIATOR SUPPORT SEAL