When the ignition switch is ON, the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) is operated by the power window regulator switch assembly. The front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) has motor, regulator and ECU functions.
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Check that the window lock switch is off before performing the following procedure.
Inspect the fuses for circuits related to this system before performing the following procedure.
Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Communication PDoor Motor | Connection status between front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) and main body ECU (multiplex network body ECU) / STOP or OK | STOP: Communication stopped
OK: Normal communication |
- |
On the GTS screen, OK is displayed.
OK
NG
(See pagePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P Door P/W Up SW | Front passenger door power window manual up switch signal / OFF or ON | OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated |
- |
| P Door P/W Down SW | Front passenger door power window manual down switch signal / OFF or ON | OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated |
- |
On the GTS screen, ON or OFF is displayed accordingly.
OK
NG
Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF/UP/DOWN | - |
Up and down movement does not occur if the arrow is not pressed and held.
Front passenger door power window operates normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Remove the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).
Inspect the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION).
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the J1 power window regulator switch assembly connector.
Disconnect the J7 front power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-6 (UP) - J7-10 (UP) | Always | Below 1 Ω |
| J1-7 (DOWN) - J7-7 (DOWN) | Always | Below 1 Ω |
| J1-6 (UP) - Body ground | Always | 10 kΩ or higher |
| J1-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the K10 power window regulator switch assembly connector.
Disconnect the K7 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-6 (UP) - K7-10 (UP) | Always | Below 1 Ω |
| K10-7 (DOWN) - K7-7(DOWN) | Always | Below 1 Ω |
| K10-6 (UP) - Body ground | Always | 10 kΩ or higher |
| K10-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
OK
NG