The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies.
The power window regulator motor assemblies have motor, regulator and ECU functions.
This DTC is output when a power window regulator motor assembly is malfunctioning, or the ECU built into the power window regulator motor assembly determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | Either condition is met: (a)
Front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is malfunctioning (b)
When ECU in front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position |
·
Front power window regulator motor assembly RH (for RHD) ·
Front power window regulator motor assembly LH (for LHD) ·
Incorrect installation of power window components ·
Overheated front power window regulator motor assembly LH (for LHD) ·
Overheated front power window regulator motor assembly RH (for RHD) ·
Harness or connector |
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | Either condition is met: (a)
Front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) is malfunctioning (b)
When ECU in front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position |
·
Front power window regulator motor assembly RH (for LHD) ·
Front power window regulator motor assembly LH (for RHD) ·
Incorrect installation of power window components ·
Overheated front power window regulator motor assembly RH (for LHD) ·
Overheated front power window regulator motor assembly LH (for RHD) ·
Harness or connector |
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | Either condition is met: (a)
Rear power window regulator motor assembly LH is malfunctioning (b)
When ECU in rear power window regulator motor assembly LH determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position |
·
Rear power window regulator motor assembly LH ·
Incorrect installation of power window components ·
Overheated rear power window regulator motor assembly LH ·
Harness or connector |
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | Either condition is met: (a)
Rear power window regulator motor assembly RH is malfunctioning (b)
When ECU in rear power window regulator motor assembly RH determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position |
·
Rear power window regulator motor assembly RH ·
Incorrect installation of power window components ·
Overheated rear power window regulator motor assembly RH ·
Harness or connector |
DTC B2311 is stored in each power window regulator motor assembly.
If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Clear the DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).
DTC B2311 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Check the parts which the DTCs have been output from.
| Result | Proceed to |
|---|---|
| DTC output from D-Door Motor (for LHD) | A |
| DTC output from D-Door Motor (for RHD) | B |
| DTC output from P-Door Motor (for LHD) | B |
| DTC output from P-Door Motor (for RHD) | A |
| DTC output from RL-Door Motor (for 5 Door) | C |
| DTC output from RR-Door Motor (for 5 Door) | D |
A
B
C
D
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-2 (B) - Body ground | Always | 11 to 14 V |
| *a | Component with harness connected
(Front Power Window Regulator Motor Assembly LH) |
OK
NG
Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
Up and down movement does not occur if the arrow is not pressed and held.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF/UP/DOWN | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF/UP/DOWN | - |
Power window regulator motor operates.
OK
NG
Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.
NEXT
Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Check the power window operation of the window for which DTC B2311 has been stored.
Power window operates normally.
OK
NG
Check that the power window components are installed correctly.
Power window components are installed correctly.
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J7-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J7-2 (B) - Body ground | Always | 11 to 14 V |
| *a | Component with harness connected
(Front Power Window Regulator Motor Assembly RH) |
OK
NG
Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
Up and down movement does not occur if the arrow is not pressed and held.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF/UP/DOWN | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF/UP/DOWN | - |
Power window regulator motor operates.
OK
NG
Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.
NEXT
Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Check the power window operation of the window for which DTC B2311 has been stored.
Power window operates normally.
OK
NG
Check that the power window components are installed correctly.
Power window components are installed correctly.
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M4-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M4-2 (B) - Body ground | Always | 11 to 14 V |
| *a | Component with harness connected
(Rear Power Window Regulator Motor Assembly LH) |
OK
NG
Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
Up and down movement does not occur if the arrow is not pressed and held.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF/UP/DOWN | - |
Power window regulator motor operates.
OK
NG
Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.
NEXT
Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Check the power window operation of the window for which DTC B2311 has been stored.
Power window operates normally.
OK
NG
Check that the power window components are installed correctly.
Power window components are installed correctly.
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-2 (B) - Body ground | Always | 11 to 14 V |
| *a | Component with harness connected
(Rear Power Window Regulator Motor Assembly RH) |
OK
NG
Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
Up and down movement does not occur if the arrow is not pressed and held.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF/UP/DOWN | - |
Power window regulator motor operates.
OK
NG
Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.
NEXT
Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Check the power window operation of the window for which DTC B2311 has been stored.
Power window operates normally.
OK
NG
Check that the power window components are installed correctly.
Power window components are installed correctly.
OK
NG