Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261239 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


PROCEDURE

Hide 75547B 1.INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedures if replacing any No. 3 windshield outside moulding clips.


a.

Install a nose piece to an air riveter or hand riveter.


b.

Insert the mandrel part of a new No. 3 windshield outside moulding clip into the nose piece.


c.
B238989

Using the riveter, install the No. 3 windshield outside moulding clips shown in the illustration.

HINT:

If the clip cannot be cut, pull it once and cut it.


NOTICE:
B171664E52
1.24,1.104 1.094,1.635 1.094,1.635 1.25,2.198 false 1.083,1.635 0.813,1.635 false 1.76,0.906 2.021,1.625 2.021,1.625 1.76,2.5 false 2.021,1.625 2.302,1.625 false 2.271,0.542 2.469,0.74 0.198,0.198 10 false *a 2.271,2.385 2.49,2.583 0.219,0.198 10 false *b 0.625,1.563 0.813,1.76 0.188,0.198 10 false *1 2.333,1.542 2.521,1.719 0.188,0.177 10 false *2

Do not pry the clip with the riveter as this will cause damage to the riveter and mandrel.


Text in Illustration
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT

NOTICE:
·
B172390E31
0.719,0.115 1.021,0.115 false 0.813,1.135 1.01,1.135 false 0.813,2.417 1.01,2.417 false 2.323,0.531 2.51,0.708 0.188,0.177 10 false *a 2.323,1.531 2.5,1.708 0.177,0.177 10 false *a 2.354,2.74 2.552,2.917 0.198,0.177 10 false *b 1.052,2.333 1.229,2.49 0.177,0.156 10 false *1 1.063,1.052 1.24,1.208 0.177,0.156 10 false *1 1.063,0.031 1.24,0.188 0.177,0.156 10 false *1

Confirm that the clips are seated properly against the moulding.

·

Do not tilt the riveter when installing the clip to the moulding.

·

Do not leave any space between the clip head and moulding.



Text in Illustration
*1 Riveter
*a INCORRECT
*b CORRECT

NOTICE:
B172391E28
0.74,0.656 0.938,0.656 false 0.74,2.125 0.948,2.125 false 2.302,1 2.5,1.177 0.198,0.177 10 false *a 2.344,2.469 2.552,2.646 0.208,0.177 10 false *b 0.99,0.563 1.188,0.729 0.198,0.167 10 false *1 0.99,2.031 1.198,2.198 0.208,0.167 10 false *1

Do not leave any space between the moulding and body. Firmly hold together the 2 items while installing the clip.


Text in Illustration
*1 Riveter
*a INCORRECT
*b CORRECT


Hide 75545B 2.INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

a.

Install the 5 No. 1 moulding clips.

HINT:

Use the same procedure to install the 5 No. 1 moulding clips on the other side.



Hide 56115A 3.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

B238996E04
1.656,0.604 1.438,0.604 false 2.604,0.583 2.823,0.583 false 1.302,0.5 1.583,0.708 0.281,0.208 10 false *1 2.865,0.5 3.115,0.729 0.25,0.229 10 false *2

a.

Install 2 new stoppers to the vehicle body as shown in the illustration.

Text in Illustration
*1 No. 1 Windshield Glass Stopper
*2 Vehicle Body


Hide 56116C 4.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Apply Primer G to the glass where the stopper will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install 2 new stoppers to the glass as shown in the illustration.

B238997E02
0.521,1.156 0.604,0.719 0.604,0.719 0.865,0.719 true 1.448,1.417 1.563,0.667 1.563,0.667 1.823,0.667 true 1.208,0.938 1.208,1.844 false 5.917,0.865 5.917,1.771 false 5.208,1.167 5.292,0.729 5.292,0.729 5.552,0.729 true 6.135,1.427 6.25,0.677 6.25,0.677 6.521,0.677 true 0.385,1.417 0.458,1.958 false 5.052,1.427 5.135,1.969 false 2.052,1.719 2.156,1.906 0.104,0.188 10 false a 0.031,0 0.219,0.208 0.188,0.208 10 false *a 0.417,1.969 0.604,2.177 0.188,0.208 10 false *c 1.125,1.875 1.313,2.083 0.188,0.208 10 false *d 1.865,0.594 2.052,0.802 0.188,0.208 10 false *b 0.875,0.646 1.063,0.854 0.188,0.208 10 false *1 6.698,1.74 6.802,1.927 0.104,0.188 10 false a 5.823,1.823 6.01,2.031 0.188,0.208 10 false *d 6.552,0.604 6.74,0.813 0.188,0.208 10 false *b 5.573,0.656 5.76,0.865 0.188,0.208 10 false *1 5.083,1.99 5.271,2.198 0.188,0.208 10 false *c

Text in Illustration
*1 Windshield Glass - -
*a Backside *b Ceramic Notch
*c Ceramic Line *d Center

Standard:
Area Specified Condition
a 14.1 mm (0.555 in.)



Hide 75533G 5.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the contact surface of the glass and moulding with Primer G as shown in the illustration.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Do not coat the adhesive with Primer G.

·

Throw away any leftover primer.



B238998E06
0.052,0 0.354,0.302 0.302,0.302 10 false *a 3.531,0.479 3.719,0.677 0.188,0.198 10 false A 3.552,0.938 3.729,1.146 0.177,0.208 10 false A 5.552,0.583 6.177,0.865 0.625,0.281 10 false A - A 6.688,1.448 6.927,1.667 0.24,0.219 10 false a

Text in Illustration
*a Backside - -

Standard:
Area Specified Condition
a 6.9 mm (0.271 in.)



b.

Remove the peeling paper from a new windshield outside moulding and install the moulding as shown in the illustration.


Hide 56117D 6.INSTALL WINDSHIELD GLASS ADHESIVE DAM

a.

Apply Primer G to the glass where the new adhesive dam will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area), but exclude the area above the notches on the upper part of the glass.

U115595E02
2.958,5.177 2.75,5.531 false 4.583,3.969 4.354,4.313 false 6.01,2.24 6.281,2.438 false 6.083,2.729 6.177,2.865 false 4.833,4 5.031,4.354 false 3.24,5.208 3.438,5.552 false 5.646,2.979 5.771,3.146 5.771,3.146 5.792,2.927 false 1.469,2.958 1.344,3.125 1.344,3.125 1.323,2.906 false 1.083,2.26 0.813,2.458 false 1.021,2.698 0.927,2.844 false 0.021,0.01 0.24,0.24 0.219,0.229 10 false *a 2.135,2.135 2.302,2.354 0.167,0.219 10 false A 2.479,2.188 2.646,2.406 0.167,0.219 10 false A 3.74,2.427 3.938,2.646 0.198,0.219 10 false B 3.76,2.781 3.958,3 0.198,0.219 10 false B 4.396,1.698 4.615,1.917 0.219,0.219 10 false A 4.719,1.635 4.938,1.854 0.219,0.219 10 false A 1.135,0.604 1.333,0.802 0.198,0.198 10 false *b 5.823,0.615 5.979,0.792 0.156,0.177 10 false *b 4.26,4.313 4.479,4.49 0.219,0.177 10 false *c 5.042,4.354 5.26,4.531 0.219,0.177 10 false *d 2.625,5.542 2.844,5.719 0.219,0.177 10 false *c 4.75,3.219 4.927,3.396 0.177,0.177 10 false a 3.927,4.448 4.115,4.677 0.188,0.229 10 false a 2.125,3.49 2.49,3.656 0.365,0.167 10 false A - A 2.125,4.594 2.49,4.76 0.365,0.167 10 false B - B 1.229,3.135 1.448,3.313 0.219,0.177 10 false *b 5.854,2.146 6.073,2.323 0.219,0.177 10 false *c 6.146,2.885 6.365,3.063 0.219,0.177 10 false *d 5.74,3.167 5.958,3.344 0.219,0.177 10 false *b 3.396,5.573 3.615,5.75 0.219,0.177 10 false *d 1.083,2.135 1.302,2.313 0.219,0.177 10 false *c 0.802,2.844 1.021,3.021 0.219,0.177 10 false *d

Text in Illustration
*a Backside *b Ceramic Notch
*c Dam Center Line *d Adhesive Center Line

Standard:
Area Specified Condition
a 6.5 mm (0.256 in.)



Hide 56111 7.INSTALL WINDSHIELD GLASS

B238990E02
1.625,0.99 1.396,0.99 1.396,0.99 1.396,1.865 true 1.323,1.885 1.583,2.115 0.26,0.229 10 false *a

a.

Position the glass.

i.

Using suction cups, place the glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing new glass. When reusing the glass, matchmarks should already be present.

·

When reusing the glass, check and correct the matchmark positions.



NOTICE:

Check that the stoppers are attached to the vehicle body correctly.



iv.

Using suction cups, remove the glass.

Text in Illustration
*a Matchmark



b.
B106085E08
2.156,0.24 2.318,0.396 0.162,0.156 10 *a 1.688,0.665 1.879,0.805 0.191,0.140 10 *1 1.66,1.744 1.851,1.884 0.191,0.140 10 *1 0.55,4.382 0.740,4.523 0.191,0.140 10 *1 1.66,2.193 1.851,2.333 0.191,0.140 10 *2 2.251,2.407 2.442,2.548 0.191,0.140 10 *b 2.303,2.285 1.891,2.285 false 2.405,1.114 1.903,0.772 false 2.369,2.184 1.868,1.843 false

Using a brush, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.



Text in Illustration
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


c.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

B239001E04
2.25,2.802 2.375,3.094 true 4.885,0.906 4.698,1.188 false 6.438,0.896 6.25,1.177 false 5.688,1.979 5.854,2.24 false 5.323,3.073 4.99,3.406 4.99,3.406 5.094,3.073 false 0.042,0 0.24,0.198 0.198,0.198 10 false *a 0.833,0.906 0.969,1.073 0.135,0.167 10 false A 0.833,1.24 1.01,1.448 0.177,0.208 10 false A 1.656,0.885 1.854,1.146 0.198,0.26 10 false B 1.667,1.208 1.865,1.469 0.198,0.26 10 false B 2.458,0.885 2.583,1.063 0.125,0.177 10 false A 2.417,1.208 2.552,1.427 0.135,0.219 10 true A 3.354,1.448 3.521,1.625 0.167,0.177 10 false C 3.646,1.365 3.813,1.542 0.167,0.177 10 false C 0.146,1.906 0.313,2.083 0.167,0.177 10 false C 0.448,2 0.615,2.177 0.167,0.177 10 false C 3.219,2.448 3.385,2.615 0.167,0.167 10 false D 3.24,2.875 3.406,3.042 0.167,0.167 10 false D 2.396,3.125 2.552,3.271 0.156,0.146 10 false *b 0.688,3.542 0.917,3.76 0.229,0.219 10 false *1 5.688,0.135 6.104,0.344 0.417,0.208 10 false A - A 4.042,0.115 4.458,0.323 0.417,0.208 10 false B - B 4.656,1.396 5.073,1.604 0.417,0.208 10 false C - C 4.354,2.458 4.771,2.667 0.417,0.208 10 false D - D 4.969,0.281 5.156,0.479 0.188,0.198 10 false a 6.531,0.26 6.719,0.458 0.188,0.198 10 false a 5.698,1.344 5.885,1.542 0.188,0.198 10 false b 5.177,2.51 5.354,2.677 0.177,0.167 10 false c 5.344,3.49 5.51,3.677 0.167,0.188 10 false d 4.552,1.156 4.708,1.302 0.156,0.146 10 false *b 6.104,1.167 6.26,1.313 0.156,0.146 10 false *b 5.865,2.219 6.021,2.365 0.156,0.146 10 false *b 4.813,3.365 4.969,3.51 0.156,0.146 10 false *b

Text in Illustration
*a Backside *b Adhesive Center Line

Standard:
Area Specified Condition
a 9.5 mm (0.374 in.)
b 3.0 mm (0.118 in.)
c 8.0 mm (0.315 in.)
d 7.0 mm (0.276 in.)


HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




d.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the glass as shown in the illustration.

B239002E06
5.698,2.104 5.99,2.396 false 6.448,1.031 6.74,1.323 false 4.906,1.031 5.188,1.323 false 5.073,3.271 5.583,3.563 5.583,3.563 5.302,3.271 false 0.042,0 0.406,0.271 0.365,0.271 10 false *a 1.646,0.146 1.854,0.375 0.208,0.229 10 false A 1.615,0.469 1.823,0.698 0.208,0.229 10 false A 0.76,0.146 0.948,0.344 0.188,0.198 10 true B 0.75,0.51 0.938,0.708 0.188,0.198 10 false B 2.406,0.156 2.594,0.354 0.188,0.198 10 false B 2.396,0.5 2.583,0.698 0.188,0.198 10 true B 0.135,1.198 0.313,1.406 0.177,0.208 10 false C 0.448,1.281 0.625,1.49 0.177,0.208 10 false C 3.323,0.698 3.542,0.917 0.219,0.219 10 false C 3.646,0.625 3.865,0.844 0.219,0.219 10 false C 3.229,1.719 3.448,1.906 0.219,0.188 10 false D 3.25,2.125 3.469,2.313 0.219,0.188 10 false D 0.135,3.01 0.375,3.219 0.24,0.208 10 false a 0.479,2.49 0.646,2.688 0.167,0.198 10 false b 0.688,3.031 1.083,3.229 0.396,0.198 10 false : *1 2.844,3.073 3.021,3.25 0.177,0.177 10 false a 3.333,3.198 3.49,3.344 0.156,0.146 10 false b 4.99,0.219 5.313,0.51 0.323,0.292 10 false c 6.521,0.208 6.823,0.49 0.302,0.281 10 false c 5.698,1.25 5.938,1.479 0.24,0.229 10 false d 5.167,2.469 5.385,2.698 0.219,0.229 10 false b 6,2.385 6.25,2.615 0.25,0.229 10 false *b 4.125,0.094 4.583,0.375 0.458,0.281 10 false A - A 5.708,0.115 6.094,0.281 0.385,0.167 10 false B - B 4.75,1.458 5.25,1.688 0.5,0.229 10 false C - C 4.448,2.406 4.885,2.615 0.438,0.208 10 false D - D 5.198,1.24 5.448,1.469 0.25,0.229 10 false *b 6.802,1.271 7.052,1.5 0.25,0.229 10 false *b 5.625,3.542 5.875,3.771 0.25,0.229 10 false *b

Text in Illustration
*1 Adhesive - -
*a Backside *b Adhesive Center Line

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 9.5 mm (0.374 in.)
d 3.0 mm (0.118 in.)




e.
B238991E01
0.427,0.571 0.255,0.408 false 0.057,0.266 0.293,0.516 0.236,0.250 10 *a

Install the glass to the vehicle body.

i.

Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.


ii.

Lightly press the outer surface of the glass to ensure that it is securely installed to the vehicle body.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.




iii.

Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours


Text in Illustration
*a Matchmark



f.

w/ Windshield Deicer System:

Connect the windshield deicer connector.


Hide 56111 8.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 63310 9.INSTALL ROOF HEADLINING ASSEMBLY

a.

for 5 Door:

i.

Return the roof headlining to its original position. Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>INSTALLATION).



b.

for 3 Door:

i.

Return the roof headlining to its original position. Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>INSTALLATION).



Hide 87810 10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87810 11.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 87834 12.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 89944 13.INSTALL RAIN SENSOR TAPE (w/ Rain Sensor)

Hide 89941 14.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 89943 15.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

Hide 62312B 27.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 28.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 75536B 33.INSTALL WINDSHIELD LOWER OUTSIDE MOULDING LH

a.

Attach the 5 clips to install a new moulding.


b.

Remove the protective tape from the edges of the moulding.


Hide 75535A 34.INSTALL WINDSHIELD LOWER OUTSIDE MOULDING RH

HINT:

Use the same procedure described for the LH side.


Hide 55781E 35.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 85211B 36.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 85221B 37.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85192 38.INSTALL WINDSHIELD WIPER ARM COVER

Hide 53867H 39.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 40.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 53828J 41.INSTALL FRONT FENDER SIDE PANEL PROTECTOR LH

Hide 53827K 42.INSTALL FRONT FENDER SIDE PANEL PROTECTOR RH

Hide 28800 44.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).