The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors, double lock door control relay assembly*1 and sliding roof drive gear sub-assembly*2. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors, double lock door control relay assembly*1 and sliding roof drive gear sub-assembly*2 is detected consecutively 3 times.
*1: w/ Double Locking System
*2: w/ Sliding Roof System
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2325 | The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors, double lock door control relay assembly*2 and sliding roof drive gear sub-assembly*3 consecutively 3 times. | ·
Multiplex network master switch assembly ·
Front power window regulator motor assembly LH ·
Front power window regulator motor assembly RH ·
Rear power window regulator motor assembly LH*1 ·
Rear power window regulator motor assembly RH*1 ·
Double lock door control relay*2 ·
Sliding roof drive gear sub-assembly*3 ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
*1: for 5 Door
*2: w/ Double Locking System
*3: w/ Sliding Roof System
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for the LIN communication stop DTC. Then perform troubleshooting for DTC B2325.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
DTC B2325 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - K4-17 (LIN1) | Always | Below 1 Ω |
| A-16 (LIN2) or K4-17 (LIN1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - J9-17 (LIN1) | Always | Below 1 Ω |
| A-16 (LIN2) or J9-17 (LIN1) - Body ground | Always | 10 kΩ or higher |
OK
NG
*1: for LHD
*2: for RHD
Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).
Reconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
*1: for LHD
*2: for RHD
Connect the K7*1 or J7*2 front power window regulator motor assembly connector.
Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
*1: for LHD
*2: for RHD
Connect the K4*1 or J9*2 multiplex network master switch assembly connector.
Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output (for 5 Door) | A |
| DTC B2325 is output (for 3 Door, w/ Double Locking System) | B |
| DTC B2325 is output (for 3 Door, w/o Double Locking System, w/ Sliding Roof System) | C |
| DTC B2325 is output (for 3 Door, w/o Double Locking System, w/o Sliding Roof System) | D |
| DTC B2325 is not output | E |
A
B
C
D
E
Connect the K7*1 or J7*2 front power window regulator motor assembly connector.
*1: for LHD
*2: for RHD
Disconnect the L4 rear power window regulator motor assembly RH connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Connect the L4 rear power window regulator motor assembly RH connector.
Disconnect the M4 rear power window regulator motor assembly LH connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output (w/ Double Locking System) | A |
| DTC B2325 is output (w/o Double Locking System, w/ Sliding Roof System) | B |
| DTC B2325 is output (w/o Double Locking System, w/o Sliding Roof System) | C |
| DTC B2325 is not output | D |
A
B
C
D
Connect the M4 rear power window regulator motor assembly LH connector.
Disconnect the G49 double lock door control relay assembly connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output (w/ Sliding Roof System) | A |
| DTC B2325 is output (w/o Sliding Roof System) | B |
| DTC B2325 is not output | C |
A
B
C
w/ Double Locking System:
Connect the G49 double lock door control relay assembly connector.
w/o Double Locking System:
Connect the M4 rear power window regulator motor assembly LH connector.
Disconnect the W20 sliding roof drive gear sub-assembly connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Connect the K7*1 or J7*2 front power window regulator motor assembly connector.
*1: for LHD
*2: for RHD
Disconnect the G49 double lock door control relay assembly connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output (w/ Sliding Roof System) | A |
| DTC B2325 is output (w/o Sliding Roof System) | B |
| DTC B2325 is not output | C |
A
B
C
w/ Double Locking System:
Connect the G49 double lock door control relay assembly connector.
w/o Double Locking System:
Connect the K7*1 or J7*2 front power window regulator motor assembly connector.
*1: for LHD
*2: for RHD
Disconnect the W20 sliding roof drive gear sub-assembly connector.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B