Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › 2016.08–2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261173 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 53292A 1.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DRAIN ENGINE COOLANT

a.

for 1GR-FE:

Drain the engine coolant (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLANT>REPLACEMENT).


b.

for 1KD-FTV:

Drain the engine coolant (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLANT>REPLACEMENT).


c.

for 2TR-FE:

Drain the engine coolant (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLANT>REPLACEMENT).


d.

for 5L-E:

Drain the engine coolant (See page Engine / Hybrid System>5L-E (COOLING)>COOLANT>REPLACEMENT).


e.

for 1GD-FTV:

Drain the engine coolant (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 88710C 5.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for Bolt Joint Type)

E322684

a.

Remove the 2 bolts.


b.
U145159E04
2.167,0.667 2.635,0.667 false 2.271,0.167 2.51,0.385 0.24,0.219 10 false *a

Disconnect the air conditioning tube and accessory assembly.

Text in Illustration
*a Disconnect tube by hand

NOTICE:
·

Do not use a screwdriver or similar tool to disconnect the tube.

·

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.




c.

Remove the grommet.


d.

Remove the 2 O-rings from the air conditioning tube and accessory assembly.


Hide 88710C 6.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for Quick Joint Type)

E200950

a.

Using SST, remove the piping clamp.

i.
E112919E04
2.365,1.375 2.676,1.545 0.311,0.17 10 SST 1.259,0.614 2.1,1.448 false 2.1,1.448 2.332,1.448 false

Attach SST to the piping clamp.

SST
09870-00015  
09870-00025  

HINT:

Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.



ii.
E112920E10
2.948,1.542 2.583,1.906 2.583,1.906 2.354,1.906 false 2.969,0.354 2.823,0.354 2.823,0.354 2.719,0.688 false 1.375,0.302 1.198,0.302 1.198,0.302 1,0.708 false 0.646,0.156 0.833,0.354 0.188,0.198 10 false *a 2.5,0.156 2.688,0.354 0.188,0.198 10 false *b 2.167,1.823 2.344,2.01 0.177,0.188 10 false *1 2.99,0.271 3.313,0.438 0.323,0.167 10 false SST 1.406,0.219 1.729,0.385 0.323,0.167 10 false SST

Push down SST and release the clamp lock.

Text in Illustration
*1 Release Lever
*a Push
*b Pull

NOTICE:

Be careful not to deform the tubes when pushing SST.



iii.

Pull SST slightly and push the release lever, then remove the piping clamp with SST.


iv.

Remove the piping clamp from SST.


v.

Disconnect the air conditioning tube and accessory assembly.

NOTICE:

Cap the open fittings immediately to keep moisture or dirt out of the system.




b.

Remove the grommet.


Hide 87245A 7.DISCONNECT HEATER WATER INLET HOSE AND HEATER WATER OUTLET HOSE

a.

Using pliers, grip the claws of the clips and slide the 2 clips.

E321808E02
0.667,0.146 0.979,0.417 0.313,0.271 10 false *A 3.969,0.146 4.281,0.417 0.313,0.271 10 false *B 0.646,1.917 0.958,2.188 0.313,0.271 10 false *C 3.938,1.917 4.25,2.188 0.313,0.271 10 false *D 0.667,3.625 0.979,3.896 0.313,0.271 10 false *E 3.969,3.615 4.281,3.885 0.313,0.271 10 false *F 0.667,5.344 0.979,5.615 0.313,0.271 10 false *G 3.969,5.344 4.281,5.615 0.313,0.271 10 false H 0.667,7.052 0.979,7.323 0.313,0.271 10 false *I 0.667,7.229 0.948,7.542 0.281,0.313 10 false *K 0.667,7.396 0.979,7.667 0.313,0.271 10 false *L 3.969,7.052 4.281,7.323 0.313,0.271 10 false *J

Text in Illustration
*A for 1GR-FE, for Single Air Conditioning System *B for 1KD-FTV, for Single Air Conditioning System
*C for 5L-E, for Single Air Conditioning System *D for 2TR-FE, for Single Air Conditioning System
*E for 1GR-FE, for Dual Air Conditioning System *F for 1KD-FTV, for Dual Air Conditioning System
*G for 5L-E, for Dual Air Conditioning System *H for 2TR-FE, for Dual Air Conditioning System
*I for 1GD-FTV, for Single Air Conditioning System *J for 1GD-FTV, for Dual Air Conditioning System
*K for 1GD-FTV, for Single Air Conditioning System
w/ Combustion Type Power Heater
*L for 1GD-FTV, for Dual Air Conditioning System
w/ Combustion Type Power Heater


b.

Disconnect the 2 heater water hoses.


Hide 85110 8.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Remove the windshield wiper motor assembly (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 9.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

a.

Remove the instrument panel sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).


Hide 45250 10.REMOVE STEERING COLUMN ASSEMBLY

a.

for Power Tilt and Power Telescopic Steering Column:

Remove the steering column assembly (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>REMOVAL).


b.

for Manual Tilt and Manual Telescopic Steering Column:

Remove the steering column assembly (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>REMOVAL).


Hide 11.REMOVE FRONT SEAT ASSEMBLY LH

a.

for Manual Seat:

Remove the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).


b.

for Power Seat:

Remove the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL).


c.

for Walk in Seat Type:

Remove the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>REMOVAL).


d.

for Bench Seat Type:

Remove the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL).


Hide 12.REMOVE FRONT SEAT ASSEMBLY RH

a.

for Manual Seat:

Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).


b.

for Power Seat:

Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL).


c.

for Walk in Seat Type:

Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>REMOVAL).


d.

for Bench Seat Type:

Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL).


Hide 58510D 13.REMOVE FRONT FLOOR CARPET ASSEMBLY

NOTICE:

It is not necessary to fully remove the floor carpet. Partially remove it so that the rear air duct can be removed in a later step.


Hide 87212G 14.REMOVE REAR NO. 3 AIR DUCT

a.
E198787

Detach the 3 clamps and 6 claws and remove the rear No. 3 air duct.


Hide 87212 15.REMOVE REAR NO. 1 AIR DUCT

a.
E198788

Detach the 3 clamps and 6 claws and the rear No. 1 air duct.


Hide 58861B 16.REMOVE NO. 1 CONSOLE BOX DUCT

a.
E198789E02
0.115,0.177 0.354,0.375 0.24,0.198 10 false *A 0.115,2.604 0.354,2.802 0.24,0.198 10 false *B

Remove the clip and No. 1 console box duct.

Text in Illustration
*A Automatic Transmission
*B Manual Transmission


Hide 55347A 17.REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET LH

a.
E198792

Remove the 2 nuts, bolt and No. 1 instrument panel brace mounting bracket LH.


Hide 55347A 18.REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET RH

a.
E198793

Remove the 2 nuts, bolt and No. 1 instrument panel brace mounting bracket RH.


Hide 87201 19.REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY

a.
E198790

Detach the 3 claws and No. 1 air duct sub-assembly.


Hide 87201B 20.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY

a.
E204225

Remove the screw.


b.

Detach the 2 claws and remove the No. 2 air duct sub-assembly.


Hide 21.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

a.

Disconnect the clamps and connectors.

E198795


b.

Remove the bolts, nuts and wire harness.

E198794


c.

Remove the instrument panel reinforcement assembly with air conditioning unit assembly.

E198796

i.

Remove the 5 caps.


ii.

Using a T40 "TORX" socket, remove the 5 "TORX" bolts.


iii.

Using a 8 mm hexagon wrench, loosen the 2 collars.


iv.

Remove the bolts, nuts and the instrument panel reinforcement assembly with air conditioning unit assembly.



Hide 55330B 22.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

Detach the 2 claws and remove the 5 bolts and instrument panel reinforcement assembly.

E200782