Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2016.08–2017.08
RM27T0E _58 Vehicle Interior _053741 INTERIOR PANELS / TRIM _0261213 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. TABLE OF BOLT, SCREW AND NUT

HINT:

All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.


B240747E04
1.948,2.938 2.396,3.104 0.448,0.167 10 false L = 18 1.979,3.104 2.458,3.281 0.479,0.177 10 false (0.709) 1.938,2.531 2.167,2.729 0.229,0.198 10 false φ 8 1.979,2.688 2.458,2.875 0.479,0.188 10 false (0.315) 5.385,3.198 6.75,3.396 1.365,0.198 10 false mm (in.) (L = Length) 0.417,0.448 0.781,0.625 0.365,0.177 10 false Code 0.469,1.156 0.76,1.333 0.292,0.177 10 false <A> 2.604,1.146 2.896,1.323 0.292,0.177 10 false <B> 4.729,1.146 5.021,1.323 0.292,0.177 10 false <C> 0.448,2.01 0.74,2.188 0.292,0.177 10 false <D> 2.594,2.021 2.885,2.198 0.292,0.177 10 false <E> 1.354,0.448 1.802,0.625 0.448,0.177 10 false Shape 2.552,0.438 2.917,0.615 0.365,0.177 10 false Code 3.552,0.448 4,0.625 0.448,0.177 10 false Shape 4.677,0.448 5.042,0.625 0.365,0.177 10 false Code 5.667,0.448 6.115,0.625 0.448,0.177 10 false Shape 1.927,0.833 2.156,1.031 0.229,0.198 10 false φ 5 2,1.021 2.479,1.208 0.479,0.188 10 false (0.197) 1.927,1.229 2.375,1.396 0.448,0.167 10 false L = 14 2,1.406 2.479,1.583 0.479,0.177 10 false (0.551) 4.094,2.083 4.542,2.25 0.448,0.167 10 false L = 20 4.125,2.24 4.604,2.417 0.479,0.177 10 false (0.787) 4.083,1.688 4.313,1.885 0.229,0.198 10 false φ 6 4.125,1.865 4.604,2.052 0.479,0.188 10 false (0.236) 6.177,0.844 6.406,1.042 0.229,0.198 10 false φ 6 6.271,1.021 6.75,1.208 0.479,0.188 10 false (0.236) 4.719,2.021 5.01,2.198 0.292,0.177 10 false <F> 0.469,2.875 0.76,3.052 0.292,0.177 10 false <G> 4.052,0.844 4.281,1.042 0.229,0.198 10 false φ 5 4.115,1.01 4.594,1.198 0.479,0.188 10 false (0.197) 4.021,1.229 4.458,1.396 0.438,0.167 10 false L = 18 4.104,1.417 4.583,1.594 0.479,0.177 10 false (0.709) 6.198,1.229 6.646,1.396 0.448,0.167 10 false L = 22 6.271,1.417 6.75,1.594 0.479,0.177 10 false (0.866) 6.094,1.854 6.323,2.052 0.229,0.198 10 false φ 6 6.156,2.031 6.635,2.219 0.479,0.188 10 false (0.236) 1.969,2.115 2.417,2.281 0.448,0.167 10 false L = 22 1.99,2.271 2.469,2.448 0.479,0.177 10 false (0.866) 1.948,1.708 2.177,1.906 0.229,0.198 10 false φ 6 1.99,1.865 2.469,2.052 0.479,0.188 10 false (0.236)

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

a.

Disable the AUTO TILT AWAY function by changing the customize parameter.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS

NOTICE:

Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.


HINT:

Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.



b.

Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.


c.

Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 84140 4.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 5.REMOVE FRONT SEAT ASSEMBLY LH

Hide 6.REMOVE FRONT SEAT ASSEMBLY RH

a.

for Manual Seat:

HINT:

Use the same procedure described for the LH side.



b.

for Power Seat:

HINT:

Use the same procedure described for the LH side.




Hide 67920 9.REMOVE DOOR SCUFF PLATE ASSEMBLY LH

Hide 67910 10.REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 11.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 12.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 13.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 14.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 74616C 15.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

Hide 74615E 16.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

HINT:

Use the same procedure described for the LH side.


Hide 62212 18.REMOVE FRONT PILLAR GARNISH LH

Hide 62211 19.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 86160J 20.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY

Hide 55318C 21.REMOVE INSTRUMENT SIDE PANEL LH

B238205C01
0,0 0,0 false
V100155

Protective Tape


a.

Put protective tape around the instrument side panel.


b.

Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.


Hide 55471A 22.REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

B238207C02
0,0 0,0 false
V100155

Protective Tape


a.

Put protective tape around the instrument cluster finish panel ornament.


b.

Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.


Hide 55476C 23.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

B238239

a.

Detach the 4 clips.


b.

Disconnect each connector and remove the instrument panel finish plate garnish.


Hide 55480D 24.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

B238214

a.

Detach the 4 clips.


b.

Disconnect each connector and remove the instrument panel finish panel.


Hide 55045 25.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

B239280C03
0,0 0,0 false
V100155

Protective Tape


a.

Using a screwdriver, detach the 2 claws and open the cover.

HINT:

Tape the screwdriver tip before use.



b.
B243715

w/o Knee Airbag:

i.

Remove the 2 bolts <C>.


ii.

Detach the 7 clips.


iii.

Disconnect each connector and each cable and remove the lower instrument panel finish panel.



c.
B238216

w/ Knee Airbag:

i.

Remove the 2 bolts <C>.


ii.

Detach the 14 clips.


iii.

Disconnect each connector and each cable and remove the lower instrument panel finish panel.



Hide 73900 26.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55404D 27.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

B238210

a.

Detach the 4 claws, 2 clips and 2 guides and remove the instrument cluster finish panel.


Hide 83100 28.REMOVE COMBINATION METER ASSEMBLY

Hide 55317A 29.REMOVE INSTRUMENT SIDE PANEL RH

B238212C01
0,0 0,0 false
V100155

Protective Tape


a.

Put protective tape around the instrument side panel.


b.

Using a moulding remover, detach the 5 clips, claw, and 3 guides.


c.

Disconnect the connector and remove the instrument side panel.


Hide 55461A 30.REMOVE INSTRUMENT PANEL ORNAMENT

B238217C01
0,0 0,0 false
V100155

Protective Tape


a.

Put protective tape around the instrument panel ornament.


b.

Using a moulding remover, detach the 5 clips and remove the instrument panel ornament.


Hide 55550 31.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

B238219C01
2.823,2.667 3.031,2.854 0.208,0.188 10 true *1 0.469,2.656 0.677,2.844 0.208,0.188 10 true *1 2.063,1.375 2.271,1.563 0.208,0.188 10 false *2 0.635,1.365 0.844,1.552 0.208,0.188 10 true *2
*1 Bolt
*2 Screw


a.

Remove the 2 bolts <C> and 2 screws <A> or <B>.


b.

Detach the 5 clips and claw.


c.

Disconnect each connector and remove the glove compartment door.


Hide 85970A 32.REMOVE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Telematics Transceiver, Double Door Lock)

Hide 86741A 33.REMOVE TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)

Hide 859A1 34.REMOVE DRIVING SUPPORT SWITCH CONTROL ECU

Hide 89533 35.REMOVE 4 WHEEL DRIVE CONTROL ECU

Hide 55420A 36.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Navigation System)

B356214

a.

Detach the 10 clips and remove the center instrument cluster finish panel.


b.

Disconnect each connector.


Hide 55522B 37.REMOVE RADIO TUNER OPENING COVER (w/o Audio)

B238208

a.

Remove the 4 bolts and radio tuner opening cover.


Hide 86120 38.REMOVE RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)

Hide 86431 39.REMOVE DISPLAY AND NAVIGATION MODULE DISPLAY (w/ Navigation System)

Hide 55406B 40.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o CRAWL)

B238201

a.

Remove the 2 bolts <E>.


b.

Detach the 3 clips and guide and remove the lower center instrument cluster finish panel.


Hide 55936E 41.REMOVE CENTER CLUSTER MODULE SWITCH (w/ CRAWL)

Hide 55421B 42.REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL

B361965

a.

Detach the 8 clips and 2 guides and remove the upper instrument cluster finish panel.


Hide 86160L 43.REMOVE FRONT NO. 4 SPEAKER ASSEMBLY

Hide 55650 44.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

B238221

a.

Detach the 4 clips and remove the No. 1 instrument panel register.


Hide 55660 45.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

HINT:

Use the same procedure described for the No. 1 instrument panel register.


Hide 55408F 46.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

B238223C01
0,0 0,0 false
V100155

Protective Tape


a.

Put protective tape around the No. 1 instrument panel speaker panel.


b.

Using a screwdriver, detach the 2 clips, claw, and 2 guides and remove the No. 1 instrument panel speaker panel.

HINT:

Tape the screwdriver tip before use.



Hide 55409F 47.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:

Use the same procedure described for the No. 1 instrument panel speaker panel.


Hide 86160P 48.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

Hide 55401E 49.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

a.

for LHD:

i.

Partially remove the floor carpet.

HINT:

It is not necessary to fully remove the floor carpet. Partially remove it so that the No. 2 instrument panel wire can be removed in a later step.



ii.

Remove the 6 bolts <E> and nut <F>.


iii.

Remove the 2 passenger airbag bolts <G>.


iv.

Remove the 4 bolts, 2 nuts and 2 brackets.


v.

Disconnect the connectors and detach the clamps and claws.


vi.

Detach the 2 guides and remove the instrument panel safety pad.

B361966C01
3.469,4.677 3.75,4.771 false 3.75,4.771 3.875,4.771 false 6.563,6.438 6.167,6.354 6.167,6.354 5.99,6.354 true 1,2.604 1.229,2.813 0.229,0.208 10 false *1 3.323,5.25 3.552,5.458 0.229,0.208 10 false *1 1.958,5.26 2.188,5.469 0.229,0.208 10 false *1 4.823,4.021 5.052,4.229 0.229,0.208 10 true *1 6.354,2.583 6.583,2.792 0.229,0.208 10 false *1 5.438,1.427 5.667,1.635 0.229,0.208 10 false *1 5.479,4.479 5.708,4.688 0.229,0.208 10 true *3 6.646,4.5 6.875,4.708 0.229,0.208 10 true *3 3.042,0.177 3.271,0.385 0.229,0.208 10 false *4 3.865,4.688 4.094,4.896 0.229,0.208 10 true *5 5.823,6.271 6.052,6.479 0.229,0.208 10 true *5 2.781,4.708 3.01,4.917 0.229,0.208 10 false *2
*1 Bolt <E> *2 Nut <F>
*3 Bolt <G> *4 Guide
*5 Bracket - -




b.

for RHD:

i.

Partially remove the floor carpet.

HINT:

It is not necessary to fully remove the floor carpet. Partially remove it so that the No. 2 instrument panel wire can be removed in a later step.



ii.

Remove the 6 bolts <E> and nut <F>.


iii.

Remove the 2 passenger airbag bolts <G>.


iv.

Remove the 4 bolts, 2 nuts and 2 brackets.


v.

Disconnect the connectors and detach the clamps and claws.


vi.

Detach the 2 guides and remove the instrument panel safety pad.

B361859C02
3.323,4.74 3.469,5.115 true 5.833,6.313 5.99,6.313 5.99,6.313 6.458,6.427 true 5.375,1.385 5.615,1.583 0.24,0.198 10 false *1 0.917,2.594 1.156,2.792 0.24,0.198 10 false *1 6.375,2.438 6.615,2.635 0.24,0.198 10 false *1 5.281,4.396 5.521,4.594 0.24,0.198 10 false *1 3.063,5.094 3.302,5.292 0.24,0.198 10 false *1 1.969,5.25 2.208,5.448 0.24,0.198 10 false *1 5.677,6.229 5.875,6.406 0.198,0.177 10 true *a 3.417,5.115 3.615,5.292 0.198,0.177 10 true *a 6.115,3.313 6.354,3.51 0.24,0.198 10 false *2 1.385,6.438 1.583,6.615 0.198,0.177 10 true *3 2.375,6.448 2.573,6.625 0.198,0.177 10 true *3 2.26,0.24 2.5,0.438 0.24,0.198 10 true *b
*1 Bolt <E> *2 Nut <F>
*3 Bolt <G> *4 Guide
*5 Bracket - -