Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › 2016.08–2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261183 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL COOLER DRYER

a.

Using pliers, install the cooler dryer.


b.
I032475

Apply a sufficient amount of compressor oil to the contact surfaces of a new O-ring and the cap.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


c.

Install the O-ring to the cap.


d.

Using a 14 mm socket hexagon wrench, install the cap to the modulator.

Torque:
2.9 N*m (30 kgf*cm, 26 in.*lbf)


Hide 88460 2.INSTALL COOLER CONDENSER ASSEMBLY

a.
E202536E03
0.583,0.688 0.719,0.865 0.135,0.177 10 true A 2.656,0.583 2.792,0.76 0.135,0.177 10 true B 3.125,0.729 3.26,0.906 0.135,0.177 10 true B

Install the cooler condenser assembly with the 3 bolts as shown in the illustration.

Torque:
for bolt A : 5.4 N*m (55 kgf*cm, 48 in.*lbf)
for bolt B : 4.4 N*m (44 kgf*cm, 39 in.*lbf)

HINT:

If the cooler condenser assembly is replaced with a new one, add compressor oil to the new cooler condenser assembly.


Capacity:

40 cc (1.35 fl.oz)


Compressor Oil:
for HFC-134a(R134a):

ND-OIL 8 or equivalent

for HFO-1234yf(R1234yf):

ND-OIL 12 or equivalent



Hide 88703 3.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the hose and the connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly joint.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


c.

Install the O-ring to the discharge hose sub-assembly.


d.

Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

When tightening the bolt, do not allow any tools to contact the pipe.

·

When tightening the bolt, hold a part of the pipe near the connector.




Hide 88463A 4.CONNECT NO. 2 COOLER CONDENSER BRACKET

a.

Install the 2 bolts and No. 2 cooler condenser bracket.


Hide 88463 5.CONNECT NO. 1 COOLER CONDENSER BRACKET

a.

Install the 2 bolts and No. 1 cooler condenser bracket.


Hide 88710 6.INSTALL AIR CONDITIONING TUBE ASSEMBLY

a.

Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube assembly joint.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


c.

Install the O-ring to the air conditioning tube assembly.


d.

Connect the air conditioning tube assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

When tightening the bolt, do not allow any tools to contact the pipe.

·

When tightening the bolt, hold a part of the pipe near the connector.




Hide 16400 8.INSTALL RADIATOR ASSEMBLY

a.

for 1GR-FE:

Install the radiator assembly (See page Engine / Hybrid System>1GR-FE (COOLING)>RADIATOR>INSTALLATION).


b.

for 2TR-FE:

Install the radiator assembly (See page Engine / Hybrid System>2TR-FE (COOLING)>RADIATOR>INSTALLATION).


c.

for 1KD-FTV:

Install the radiator assembly (See page Engine / Hybrid System>1KD-FTV (COOLING)>RADIATOR>INSTALLATION).


d.

for 5L-E:

Install the radiator assembly (See page Engine / Hybrid System>5L-E (COOLING)>RADIATOR>INSTALLATION).


e.

for 1GD-FTV:

Install the radiator assembly (See page Engine / Hybrid System>1GD-FTV (COOLING)>RADIATOR>INSTALLATION).


Hide 9.ADD ENGINE COOLANT

a.

for 1GR-FE:

Add engine coolant (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLANT>REPLACEMENT).


b.

for 2TR-FE:

Add engine coolant (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLANT>REPLACEMENT).


c.

for 1KD-FTV:

Add engine coolant (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLANT>REPLACEMENT).


d.

for 5L-E:

Add engine coolant (See page Engine / Hybrid System>5L-E (COOLING)>COOLANT>REPLACEMENT).


e.

for 1GD-FTV:

Add engine coolant (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).


Hide 11.INSPECT FOR ENGINE COOLANT LEAK

a.

for 1GR-FE:

Inspect for engine coolant leak (See page Engine / Hybrid System>1GR-FE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).


b.

for 2TR-FE:

Inspect for engine coolant leak (See page Engine / Hybrid System>2TR-FE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).


c.

for 1KD-FTV:

Inspect for engine coolant leak (See page Engine / Hybrid System>1KD-FTV (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).


d.

for 5L-E:

Inspect for engine coolant leak (See page Engine / Hybrid System>5L-E (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION).


e.

for 1GD-FTV:

Inspect for engine coolant leak (See page Engine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT).