Refer to DTC P2006 (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2006).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | Open in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic). | ·
Vacuum switching valve (for swirl control valve) ·
Open in vacuum switching valve (for swirl control valve) circuit ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | Short in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic). | ·
Vacuum switching valve (for swirl control valve) ·
Short in vacuum switching valve (for swirl control valve) circuit ·
ECM |
Refer to DTC P2006 (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2006).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Disconnect the vacuum hoses from the vacuum switching valve (for Swirl Control Valve).
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
Check the VSV operation when it is operated using the intelligent tester.
| Tester Operation | Specified Condition |
|---|---|
| VSV ON | Air from port E flows out through port F |
| VSV OFF | Air from port E flows out through air filter |
Reconnect the vacuum hoses.
OK
(See pageEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
NG
Inspect the vacuum switching valve (for swirl control valve) (See page Engine / Hybrid System>1KD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSPECTION).
OK
NG
Disconnect the vacuum switching valve (for swirl control valve) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C143-2 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to vacuum switching valve (for swirl control valve)) |
OK
NG
Disconnect the vacuum switching valve (for swirl control valve) connector.
Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C143-1 - C93-2 (SCV) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C143-1 or C93-2 (SCV) - Body ground | Always | 10 kΩ or higher |
Reconnect the vacuum switching valve (for swirl control valve) connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Disconnect the No. 1 integration relay connector.
Disconnect the vacuum switching valve (for swirl control valve) connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1W-10 - C143-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1W-10 or C143-2 - Body ground | Always | 10 kΩ or higher |
Reconnect the No. 1 integration relay connector.
Reconnect the vacuum switching valve (for swirl control valve) connector.
OK
NG
Check the ECM power source circuit (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>ECM Power Source Circuit).
NEXT
Replace the vacuum switching valve (for swirl control valve) (See page Engine / Hybrid System>1KD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL).
NEXT
Repair or replace harness or connector.
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
NEXT