Check the 4WD drive mode.
| Result | Proceed to |
|---|---|
| 4 Drive Mode (H4F, H4L, L4F or L4L) (for 1GR-FE, 1GD-FTV or 1KD-FTV ) | A |
| 3 Drive Mode (H4F, H4L, or L4L) (for 2TR-FE or 5L-E) | B |
A
B
Confirm the problem symptoms.
| Result | Proceed to |
|---|---|
| The 4LO indicator light remains off after operating the transfer position switch (combination switch assembly) to L4*1
The 4LO indicator light remains off after operating the transfer position switch to L4*2 |
A |
| The 4LO indicator light remains on after operating the transfer position switch (combination switch assembly) to H4*1
The 4LO indicator light remains on after operating the transfer position switch to H4*2 |
B |
*1: w/ Combination Switch
*2: w/o Combination Switch
A
B
Perform the following procedure with the vehicle stopped.
Turn the ignition switch to ON.
for Automatic Transmission:
Move the shift lever to N.
for Manual Transmission:
Depress the clutch pedal.
w/ Combination Switch:
Turn the transfer position switch (combination switch assembly) to L4.
w/o Combination Switch:
Turn the transfer position switch to L4.
Check the 4LO indicator light.
| Result | Proceed to |
|---|---|
| The 4LO indicator light remains off | A |
| The 4LO indicator light is blinking or illuminated | B |
Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
A
B
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
"Bus Check" indicates no malfunctions in CAN communication.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Transfer Position Control SW | Transfer position switch status/
ON or OFF |
ON: L4
OFF: H4 |
- |
w/ Combination Switch:
Display changes according to transfer position switch (combination switch assembly) operation.
w/ Combination Switch
Display changes according to transfer position switch operation.
OK
NG
Turn the ignition switch off.
Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
Check the combination meter assembly.
The 4LO indicator light turns on or off in accordance with the GTS.
OK
NG
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
w/ Combination Switch:
Remove the transfer position switch (combination switch assembly) (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/ Combination Switch)>REMOVAL).
Inspect the transfer position switch (combination switch assembly (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/ Combination Switch)>INSPECTION).
The transfer position switch (combination switch assembly) operates normally.
w/o Combination Switch:
Remove the transfer position switch (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>REMOVAL).
Inspect the transfer position switch (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>ON-VEHICLE INSPECTION).
The transfer position switch operates normally.
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | w/ Combination Switch | B |
| w/o Combination Switch | C | |
A
B
C
(See pageDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>REMOVAL)
Disconnect the G53 4 wheel drive control ECU connector.
w/ Combination Switch:
Disconnect the G305 transfer position switch (combination switch assembly) connector.
w/o Combination Switch:
Disconnect the G18 transfer position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-13 (LO) - G305-2 (LO) | Always | Below 1 Ω |
| G53-13 (LO) or G305-2 (LO) - Body ground | Always | 10 kΩ or higher |
| G305-4 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-13 (LO) - G18-2 (LO) | Always | Below 1 Ω |
| G53-13 (LO) or G18-2 (LO)) - Body ground | Always | 10 kΩ or higher |
| G18-4 (GND) - Body ground | Always | Below 1 Ω |
OK
NG
Perform the following procedure with the vehicle stopped.
Turn the ignition switch to ON.
for Automatic Transmission:
Move the shift lever to N.
for Manual Transmission:
Depress the clutch pedal.
w/ Combination Switch:
Turn the transfer position switch (combination switch assembly) to L4.
w/o Combination Switch:
Turn the transfer position switch to L4.
Check the 4LO indicator light.
| Result | Proceed to |
|---|---|
| The 4LO indicator light remains illuminated | A |
| The 4LO indicator light is blinking or illuminated | B |
Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
A
B
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
"Bus Check" indicates no malfunctions in CAN communication.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L4 Indicator Request | 4LO indicator light request/
Blink3, Blink2*, Blink1, ON, OFF |
·
Blink3: Indicator light rapidly blinks ·
Blink1: Indicator light blinks ·
ON: Indicator light illuminates ·
OFF: Indicator light turns off |
·
Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off) ·
Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off) |
*: Item not equipped, therefore not displayed
w/ Combination Switch:
Operate the transfer position switch (combination switch assembly) several times between H4 and L4, and then check the GTS display condition of the 4LO indicator light.
w/o Combination Switch:
Operate the transfer position switch several times between H4 and L4, and then check the GTS display condition of the 4LO indicator light.
| Result | Proceed to |
|---|---|
| Data List continues to display ON even when transfer position switch (combination switch assembly) is operated*1
Data List continues to display ON even when transfer position switch is operated*2 |
A |
| Data List display changes according to transfer position switch (combination switch assembly) operation*1
Data List display changes according to transfer position switch operation*2 |
B |
*1: w/ Combination Switch
*2: w/o Combination Switch
A
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Confirm the problem symptoms.
| Result | Proceed to |
|---|---|
| The center differential lock indicator light and 4LO indicator light remain off | A |
| The center differential lock indicator light remains illuminated, and the 4LO indicator light remains off | B |
| The center differential lock indicator light) and 4LO indicator light remain illuminated | C |
A
B
C
Turn the ignition switch to ON.
for Automatic Transmission:
Move the shift lever to N.
for Manual Transmission:
Depress the clutch pedal.
Turn the transfer position switch to H4L.
Wait for 60 seconds.
Check the center differential lock indicator light.
| Result | Proceed to |
|---|---|
| The center differential lock indicator light blinks*1 or illuminates | A |
| The center differential lock indicator light rapidly blinks*2 or remains off | B |
*1 (Blinking): Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
*2 (Rapidly blinking): Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
A
B
Turn the transfer position switch to L4L.
Check if DTC P279E is output after 60 seconds elapse (See page ).
| Result | Proceed to |
|---|---|
| DTC P279E is not output | A |
| DTC P279E is output | B |
A
B
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.
w/ Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
w/o Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM
"Bus Check" indicates no malfunctions in CAN communication.
| Result | Proceed to | |
|---|---|---|
| DTC is not output | A | |
| DTC is output | w/ Central Gateway ECU | B |
| w/o Central Gateway ECU | C | |
A
B
C
| *a | Component with harness connected
(Transfer Position Switch) |
Remove the transfer position switch with its connector still connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G18-5 (HI) - Body ground | Ignition switch ON
H4F position |
Below 1.5 V |
| Ignition switch ON
H4L position |
Below 1.5 V | |
| Ignition switch ON
L4L position |
10.5 to 14 V | |
| G18-2 (LO) - Body ground | Ignition switch ON
H4F position |
10.5 to 14 V |
| Ignition switch ON
H4L position |
Below 1.5 V | |
| Ignition switch ON
L4L position |
Below 1.5 V |
OK
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
(See pageDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>REMOVAL)
Turn the ignition switch to ON.
for Automatic Transmission:
Move the shift lever to N.
for Manual Transmission:
Depress the clutch pedal.
Turn the transfer position switch to H4F.
Wait for 60 seconds.
Check the center differential lock indicator light.
| Result | Proceed to |
|---|---|
| The center differential lock indicator light blinks*1 or turns off | A |
| The center differential lock indicator light rapidly blinks*2 or remains on | B |
*1 (Blinking): Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
*2 (Rapidly blinking): Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
A
B
Perform the following procedures with the vehicle stopped.
Turn the ignition switch to ON.
for Automatic Transmission:
Move the shift lever to N.
for Manual Transmission:
Depress the clutch pedal.
Turn the transfer position switch to H4L.
Wait for 60 seconds.
Check the 4LO indicator light.
| Result | Proceed to |
|---|---|
| The 4LO indicator light blinks*1 or turns off | A |
| The 4LO indicator light rapidly blinks*2 or remains on | B |
*1 (Blinking): Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
*2 (Rapidly blinking): Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
A
B
Turn the transfer position switch to H4F.
Check if DTC P279E is output after 60 seconds elapse.
| Result | Proceed to |
|---|---|
| DTC P279E is not output | A |
| DTC P279E is output | B |
A
B
| *a | Component with harness connected
(Transfer Position Switch) |
Remove the transfer position switch with its connector still connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G18-5 (HI) - Body ground | Ignition switch ON
H4F position |
Below 1.5 V |
| Ignition switch ON
H4L position |
Below 1.5 V | |
| Ignition switch ON
L4L position |
10.5 to 14 V | |
| G18-2 (LO) - Body ground | Ignition switch ON
H4F position |
10.5 to 14 V |
| Ignition switch ON
H4L position |
Below 1.5 V | |
| Ignition switch ON
L4L position |
Below 1.5 V |
| Result | Proceed to | |
|---|---|---|
| OK | w/ Central Gateway ECU | A |
| w/o Central Gateway ECU | B | |
| NG | C | |
A
B
C
(See pageDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>REMOVAL)