Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
64714C
1.INSTALL DECK SIDE TRIM COVER RH (w/o Spare Tire)
Attach the 7 claws and 3 guides to install the deck side trim cover RH.
Turn the 2 knobs to engage the lock.
64766B
2.INSTALL QUARTER TRIM JACK COVER (w/ Spare Tire)
Attach the 7 claws and 3 guides to install the quarter trim jack cover.
62627B
3.INSTALL QUARTER TRIM COVER
Use the same procedure for the other quarter trim cover.
Attach the 2 claws to install the quarter trim cover.
73372
4.INSTALL REAR SEAT SHOULDER BELT HANGER LH
Use the same procedure for the other rear seat shoulder belt hanger.
Attach the claw and guide to install the rear seat shoulder belt hanger LH.
73371
5.INSTALL REAR SEAT SHOULDER BELT HANGER RH
Use the same procedure described for the LH side.
64746F
6.INSTALL DECK SIDE TRIM CUP HOLDER LH
Attach the 4 claws to install the deck side trim cup holder LH.
64745H
7.INSTALL DECK SIDE TRIM CUP HOLDER RH
Use the same procedure described for the LH side.
66425A
8.INSTALL REAR NO. 2 SIDE RAIL SPACER LH
Attach the 4 claws to install the rear No. 2 side rail spacer LH.
Install the clip.
66415A
9.INSTALL REAR NO. 2 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
73024
10.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
Attach the 4 claws to install the front shoulder belt anchor plate sub-assembly LH.
73023
11.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
63310
12.INSTALL ROOF HEADLINING ASSEMBLY
Place the roof headlining assembly into the vehicle through the back door.
Be careful not to damage the roof headlining assembly when placing it in the cabin.
w/o Sliding Roof:
Attach the 2 clips to install the roof headlining assembly.
| *a | Guide |
| *b | Fastener |
w/ Sliding Roof:
Attach the 2 clips, 2 guides and 8 fasteners to install the roof headlining.
Connect the connector and attach the 4 clamps to the rear pillar RH.
Connect the connector and attach the 3 clamps to the rear pillar LH.
Connect the 2 connectors and attach the 3 clamps to the front pillar RH.
Install the bolt.
Connect the 2 connectors and attach the 3 clamps to the front pillar LH.
w/ Digital Audio Broadcasting Antenna:
Connect the connector and attach the wire harness clamp.
w/ Pre-crash Safety System:
Attach the hook to install the camera earth with the bolt.
w/ Sliding Roof
Connect the drive gear connector.
w/ Rain Sensor:
Connect the rain sensor connector.
w/ EC Mirror:
Connect the inner mirror connector.
| *A | w/ Camera Heater |
w/ Pre-crash Safety System:
Connect the 2 connectors.
w/ Pre-crash Safety System, w/ Camera Heater:
Connect the 3 connectors.
74348
13.INSTALL VISOR HOLDER
74320
14.INSTALL VISOR ASSEMBLY LH
74310
15.INSTALL VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74318
16.INSTALL VISOR BRACKET COVER LH
74317
17.INSTALL VISOR BRACKET COVER RH
Use the same procedure described for the LH side.
62432B
18.INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH
| *a | New Clip |
Install 5 new clips to the No. 1 roof side rail garnish LH.
Attach the 5 clips to install the No. 1 roof side rail garnish LH.
62431B
19.INSTALL NO. 1 ROOF SIDE RAIL GARNISH RH
Use the same procedure described for the LH side.
81240D
20.INSTALL NO. 2 ROOM LIGHT ASSEMBLY
81240
21.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
86466D
22.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)
86466E
23.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)
87834
24.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
89943
25.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
81260A
26.INSTALL MAP LIGHT ASSEMBLY
74610U
27.INSTALL REAR ASSIST GRIP ASSEMBLY LH
74610V
28.INSTALL REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure described for the LH side.
74610A
29.INSTALL ASSIST GRIP SUB-ASSEMBLY
62640P
30.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH
Attach the 4 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear quarter trim panel assembly LH.
Attach the 7 clips to install the rear quarter trim panel assembly LH.
62630P
31.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH
Use the same procedure described for the LH side.
62520P
32.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
Pass the front seat outer belt floor anchor through the front quarter trim panel assembly LH.
Attach the 2 clips and 2 guides to install the front quarter trim panel assembly LH.
Install the bolt.
62510P
33.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
Use the same procedure described for the LH side.
64740C
34.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Attach the 9 claws and 12 clips to install the deck trim side panel assembly LH.
Install the 3 bolts and 2 screws.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
Install the front seat outer belt floor anchor with the bolt.
64730B
35.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
Connect the connector.
Attach the 9 claws and 12 clips to install the deck trim side panel assembly RH.
Install the 3 bolts and 2 screws.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
Install the front seat outer belt floor anchor with the bolt.
73233
36.INSTALL OUTER LAP BELT ANCHOR COVER
Use the same procedure for the other outer lap belt anchor cover.
Attach the 3 claws to install the outer lap belt anchor cover.
62596D
37.INSTALL QUARTER TRIM POCKET TRAY
Attach the 6 claws and 2 guides to install the quarter trim pocket tray.
64712F
38.INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)
Use the same procedure for the other front deck side trim cover.
Attach the 2 claws to install the front deck side trim cover.
64937A
39.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
Use the same procedure for the other tonneau cover holder cap.
Attach the 2 claws to install the No. 1 tonneau cover holder cap.
64725D
40.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Use the same procedure for the other No. 1 luggage compartment trim hook.
Install the No. 1 luggage compartment trim hook so that it is positioned horizontally.
58570C
41.INSTALL REAR FLOOR CARPET ASSEMBLY
Install the rear floor carpet assembly.
62538E
42.INSTALL QUARTER TRIM COVER HOLE LH
Attach the 2 claws and 2 guides to install the quarter trim cover hole LH.
62538C
43.INSTALL QUARTER TRIM COVER HOLE RH
Use the same procedure described for the LH side.
58574A
44.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
Attach the 6 claws to install the rear floor mat rear support plate.
Install the 5 screws.
58649C
45.INSTALL MAT SET PLATE COVER
Use the same procedure for all mat set plate covers.
Attach the 2 claws to install the mat set plate cover.
64910M
46.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Install the tonneau cover assembly.
62212
47.INSTALL FRONT PILLAR GARNISH LH
62211
48.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
74611F
49.INSTALL NO. 1 ASSIST GRIP
74616C
50.INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH
74615E
51.INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH
Use the same procedure described for the LH side.
62312B
52.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
53.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62112
54.INSTALL COWL SIDE TRIM BOARD LH
62111C
55.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
67920
56.INSTALL DOOR SCUFF PLATE ASSEMBLY LH
67910
57.INSTALL DOOR SCUFF PLATE ASSEMBLY RH
Use the same procedure described for the LH side.
58.INSTALL REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)
59.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION