Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for 5 Door) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053741 INTERIOR PANELS / TRIM _0261217 ROOF HEADLINING(for 5 Door) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for 5 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 66426B 1.INSTALL REAR NO. 3 SIDE RAIL SPACER LH

a.

Attach the 2 claws to install the rear No. 3 side rail spacer LH.


Hide 66416 2.INSTALL REAR NO. 3 SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 66425A 3.INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.

Attach the 2 claws to install the rear No. 2 side rail spacer LH.


Hide 66415A 4.INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 66424 5.INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.

Attach the 2 claws to install the rear side rail spacer LH.


Hide 66414A 6.INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 64715C 7.INSTALL DECK SIDE TRIM COVER LH

a.

Attach the 3 claws and 2 guides to install the deck side trim cover LH.


Hide 64766B 8.INSTALL QUARTER TRIM JACK COVER

a.

Attach the 3 claws and 2 guides to install the quarter trim jack cover.


Hide 62627B 9.INSTALL QUARTER TRIM COVER

HINT:

Use the same procedure for the other quarter trim cover.


a.

Attach the 2 claws to install the quarter trim cover.


Hide 73372 10.INSTALL REAR SEAT SHOULDER BELT HANGER LH

a.

Attach the claw and guide to install the rear seat shoulder belt hanger LH.


Hide 73371 11.INSTALL REAR SEAT SHOULDER BELT HANGER RH

HINT:

Use the same procedure described for the LH side.


Hide 62477A 12.INSTALL ROOF SIDE INNER GARNISH CAP LH (w/o Rear No. 2 Seat)

a.

Attach the 4 claws and 2 guides to install the roof side inner garnish cap LH.


Hide 62476A 13.INSTALL ROOF SIDE INNER GARNISH CAP RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 73034 14.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

a.

Attach the 6 claws to install the rear belt anchor plate sub-assembly LH.


Hide 73033 15.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73024 16.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

a.

Attach the 5 claws to install the front belt anchor plate sub-assembly LH.


Hide 73023 17.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 63310 18.INSTALL ROOF HEADLINING ASSEMBLY

a.

Place the roof headlining into the vehicle through the back door.

NOTICE:

Be careful not to damage the roof headlining when placing it in the cabin.



b.
B238765

w/o Sliding Roof:

i.

Attach the 2 clips to install the roof headlining assembly.



c.
B238767C03
0.948,2.292 0.958,2.75 0.958,2.75 1.208,2.302 true 0.948,1.021 0.958,0.49 0.958,0.49 1.188,1.021 true 1.438,1.51 1.854,1.625 false 1.427,1.771 1.854,1.625 false 1.438,1.292 1.854,1.635 false 1.427,2.021 1.854,1.635 false 0.573,2.083 0.156,2.75 0.156,2.75 0.281,2.75 true 0.563,1.229 0.198,0.531 0.198,0.531 0.344,0.531 true 0.344,2.667 0.552,2.865 0.208,0.198 10 false *a 0.875,2.75 1.083,2.948 0.208,0.198 10 false *b 0.406,0.458 0.615,0.656 0.208,0.198 10 false *a 0.844,0.313 1.052,0.51 0.208,0.198 10 false *b 1.854,1.552 2.063,1.75 0.208,0.198 10 true *b
*a Guide
*b Fastener


w/ Sliding Roof:

i.

Attach the 2 clips, 2 guides and 8 fasteners to install the roof headlining assembly.



d.
B238766C02
0.948,2.26 0.948,2.74 0.948,2.74 1.208,2.313 true 0.948,1.021 0.958,0.458 0.958,0.458 1.229,1.031 true 1.427,1.99 1.813,1.604 1.813,1.604 1.406,1.313 true 0.573,2.083 0.146,2.771 0.146,2.771 0.26,2.771 false 0.563,1.24 0.208,0.563 0.208,0.563 0.365,0.563 true 0.271,2.677 0.427,2.854 0.156,0.177 10 false *a 0.865,2.75 1.021,2.927 0.156,0.177 10 false *b 0.406,0.479 0.563,0.656 0.156,0.177 10 false *a 0.875,0.281 1.031,0.458 0.156,0.177 10 false *b 1.854,1.531 2.01,1.708 0.156,0.177 10 true *b
*a Guide
*b Fastener


w/ Rear Seat Entertainment System:

i.

Attach the 2 clips, 2 guides and 6 fasteners to install the roof headlining assembly.



e.

w/ Rear Seat Entertainment System:

i.

Connect the 2 connectors.



f.

Connect the connector and attach the 3 clamps to the rear pillar RH.


g.

Connect the 2 connectors and attach the clamp to the rear pillar LH.


h.

Connect the 2 connectors and attach the 3 clamps to the front pillar RH.


i.

Install the bolt.


j.

Connect the 2 connectors and attach the 3 clamps to the front pillar LH.


k.

w/ Digital Audio Broadcasting Antenna:

i.

Connect the connector and attach the wire harness clamp.



l.

w/ Pre-crash Safety System:

i.

Attach the hook to install the camera earth with the bolt.



m.

w/ Sliding Roof

i.

Connect the drive gear connector.



n.
E197773

w/ Rain Sensor:

i.

Connect the rain sensor connector.



o.
B430357

w/ EC Mirror:

i.

Connect the inner mirror connector.



p.
B478233C04
1.031,1.625 1.406,1.865 0.375,0.24 12 false *A
*A w/ Camera Heater


w/ Pre-crash Safety System:

i.

Connect the 2 connectors.



q.

w/ Pre-crash Safety System, w/ Camera Heater:

i.

Connect the 3 connectors.



Hide 74348 19.INSTALL VISOR HOLDER

HINT:

Use the same procedure for the other visor holder.


a.

Attach the 2 claws.


b.

Push in the visor holder to install it.


Hide 74320 20.INSTALL VISOR ASSEMBLY LH

a.

Install the visor assembly LH with the 2 screws.


Hide 74310 21.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74318 22.INSTALL VISOR BRACKET COVER LH

HINT:

Use the same procedure for the other visor bracket cover.


a.

Attach the 4 claws to install the visor bracket cover LH.


Hide 74317 23.INSTALL VISOR BRACKET COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 86160T 24.INSTALL REAR HEADER SPEAKER ASSEMBLY (w/ Rear Air Conditioning System)

Hide 87217D 25.INSTALL REAR SIDE NO. 1 AIR DUCT (w/ Rear Air Conditioning System)

Hide 62432B 26.INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH

B238769C03
1.208,1.354 1.938,1.188 1.938,1.188 2.094,1.188 true 2.177,1.115 2.344,1.313 0.167,0.198 10 false *a
*a New Clip


a.

Install 3 new clips to the No. 1 roof side rail garnish LH.


b.

Attach the 3 clips to install the No. 1 roof side rail garnish LH.


Hide 62431B 27.INSTALL NO. 1 ROOF SIDE RAIL GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 86295 28.INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)

Hide 81240D 29.INSTALL NO. 2 ROOM LIGHT ASSEMBLY

Hide 81240 30.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 86466D 31.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 86466E 32.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 87834 33.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 89943 34.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

Hide 81260A 35.INSTALL MAP LIGHT ASSEMBLY

Hide 74611B 36.INSTALL ASSIST GRIP (w/ Rear No. 2 Seat)

HINT:

Use the same procedure for the other assist grip.


a.

Install the assist grip with the 2 bolts.


b.

Attach the 4 claws to close the 2 covers.


Hide 74610U 37.INSTALL REAR ASSIST GRIP ASSEMBLY LH

B169217

a.

Assemble the rear assist grip assembly LH, 2 clips and 2 covers as shown in the illustration.


b.

Install the rear assist grip sub-assembly LH.


Hide 74610V 38.INSTALL REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74610A 39.INSTALL ASSIST GRIP SUB-ASSEMBLY

B165740

a.

Assemble the assist grip sub-assembly, 2 clips and 2 covers as shown in the illustration.


b.

Install the assist grip sub-assembly.


Hide 62640P 40.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH

a.

w/o Rear No. 2 Seat:

i.

Attach the 7 clips and 2 guides to install the rear quarter trim panel assembly LH.



b.

w/ Rear No. 2 Seat:

i.

Attach the 4 clips and 2 guides and pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel.


ii.

Attach the 7 clips and 2 guides to install the rear quarter trim panel assembly LH.



Hide 62630P 41.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62520P 42.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

a.

Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel assembly LH.


b.

Attach the 2 clips and 2 guides to install the front quarter trim panel assembly LH.


Hide 62510P 43.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 64740C 44.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

w/o Rear No. 2 Seat, w/o Rear Air Conditioning System:

i.

Pass the rear seatback lock control lever base through the deck trim side panel assembly LH.


ii.

Attach the 5 clips and 8 claws to install the deck trim side panel assembly LH.


iii.

Install the 4 bolts and 2 screws.


iv.

Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly LH.


v.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



b.

w/o Rear No. 2 Seat, w/ Rear Air Conditioning System:

i.

Attach the 5 clips and 8 claws to install the deck trim side panel assembly LH.


ii.

Install the 2 bolts and 2 screws.


iii.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



c.

w/ Rear No. 2 Seat:

i.

Attach the 4 clips and 8 claws to install the deck trim side panel assembly LH.


ii.

Install the 2 bolts and 2 screws.


iii.

Install the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


iv.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



Hide 64730B 45.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

a.

w/o Rear No. 2 Seat, w/o Rear Air Conditioning System:

i.

Connect each connector.


ii.

Pass the rear seatback lock control lever base through the deck trim side panel assembly RH.


iii.

Attach the 5 clips and 8 claws to install the deck trim side panel assembly RH.


iv.

Install the 4 bolts and screw.


v.

Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly RH.


vi.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



b.

w/o Rear No. 2 Seat, w/ Rear Air Conditioning System:

i.

Connect each connector.


ii.

Attach the 4 clips and 8 claws to install the deck trim side panel assembly RH.


iii.

Install the 2 bolts and screw.


iv.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



c.

w/ Rear No. 2 Seat:

i.

Connect each connector.


ii.

Attach the 4 clips and 8 claws to install the deck trim side panel assembly RH.


iii.

Install the 2 bolts and screw.


iv.

Install the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


v.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



Hide 74603C 46.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

HINT:

Use the same procedure for the other assist grip.


a.

Install the assist grip sub-assembly with the 2 bolts.


Hide 74617A 47.INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

HINT:

Use the same procedure for all assist grip plugs.


a.

Attach the 2 claws to install the assist grip plug.


Hide 64712F 48.INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

HINT:

Use the same procedure for the other front deck side trim cover.


a.

Attach the 2 claws to install the front deck side trim cover.


Hide 64937A 49.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

HINT:

Use the same procedure for the other No. 1 tonneau cover holder cap.


a.

Attach the 2 claws to install the No. 1 tonneau cover holder cap.


Hide 64725D 50.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:

Use the same procedure for the other No. 1 luggage compartment trim hook.


a.

Install the No. 1 luggage compartment trim hook by turning it clockwise.


Hide 73233A 51.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


a.

Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.


Hide 58570C 52.INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

a.

Attach the 4 claws to install the rear floor carpet assembly.

B486236C02
1.167,0.063 1.542,0.302 0.375,0.24 12 false *A 3.531,0.073 3.906,0.313 0.375,0.24 12 false *B 1.177,1.469 1.552,1.708 0.375,0.24 12 false *C 3.5,1.49 3.875,1.729 0.375,0.24 12 false *D
*A w/o Deck Rail *B w/ Deck Rail
*C for Face to Face Seat Type *D w/ Rear Air Conditioning System



Hide 57412C 53.INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)

a.

Install the floor side rail LH with the 3 bolts.


Hide 57411D 54.INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

HINT:

Use the same procedure described for the LH side.


Hide 58574A 55.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

a.

Attach the 5 clips and 4 claws to install the rear floor mat rear support plate.


Hide 58401A 56.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

a.

w/ Rear Air Conditioning System:

i.

Attach the clip to install the No. 1 deck board sub-assembly.



b.

w/o Rear Air Conditioning System:

i.

Attach the clip to install the No. 1 deck board sub-assembly.



Hide 64717A 57.INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

B238749C04
1.365,0.885 0.698,0.438 0.698,0.438 0.531,0.438 true 0.344,0.354 0.563,0.594 0.219,0.24 10 false *1
*1 Luggage Hold Belt Striker


HINT:

Use the same procedure for the other front luggage compartment trim cover.


a.

Install the luggage hold belt striker and front luggage compartment trim cover with the bolt.


b.

Attach the 4 claws to install the cap.


Hide 64910M 58.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.

Install the tonneau cover assembly.


Hide 62412 59.INSTALL CENTER PILLAR GARNISH LH

a.

Pass the front seat outer belt floor anchor through the center pillar garnish LH.


b.

Attach the 2 clips and 2 guides to install the center pillar garnish LH.


c.

Install the bolt.


Hide 62411 60.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 74611G 61.INSTALL NO. 2 ASSIST GRIP

HINT:

Use the same procedure for the other No. 2 assist grip.


a.

Attach the 2 claws to install the No. 2 assist grip.


b.

Install the 2 bolts.


Hide 74638 62.INSTALL NO. 2 ASSIST GRIP PLUG LH

HINT:

Use the same procedure for the other front No. 2 assist grip plug.


a.

Attach the 2 claws to install the front No. 2 assist grip plug LH.


Hide 74637 63.INSTALL NO. 2 ASSIST GRIP PLUG RH

HINT:

Use the same procedure described for the LH side.


Hide 62414A 64.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 4 claws and 2 clips to install the lower center pillar garnish LH.


b.

Install the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62413A 65.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 73233 66.INSTALL OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for the other outer lap belt anchor cover.


a.

Attach the 3 claws to install the outer lap belt anchor cover.


Hide 62332C 67.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

B238781C03
1.052,1.521 1.229,1.365 false 1.229,1.365 1.323,1.365 false 1.354,1.281 1.604,1.469 0.25,0.188 10 false *a 0.948,0.917 1.198,1.104 0.25,0.188 10 false *b
*a Paint Mark
*b Mark Position


a.

Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle and install the rear door opening trim weatherstrip LH as shown in the illustration.


Hide 62331C 68.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 67918D 69.INSTALL REAR DOOR SCUFF PLATE LH

a.

Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate LH.


Hide 67917C 70.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 67934 71.INSTALL INSIDE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

a.

Install the quarter scuff plate LH with the 2 bolts.


Hide 67933 72.INSTALL INSIDE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 58371F 73.INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

HINT:

Use the same procedure for all rear No. 1 floor step covers.


a.

Attach the 2 claws to install the rear No. 1 floor step cover.


Hide 62212 74.INSTALL FRONT PILLAR GARNISH LH

a.

Attach the 3 guides to install the front pillar garnish LH.


Hide 62211 75.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 74611F 76.INSTALL NO. 1 ASSIST GRIP

HINT:

Use the same procedure for the other No. 1 assist grip.


a.

Attach the 2 claws to install the No. 1 assist grip.


b.

Install the 2 bolts.


Hide 74616C 77.INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH

HINT:

Use the same procedure for the other front No. 1 assist grip plug.


a.

Attach the 2 claws to install the front No. 1 assist grip plug LH.


Hide 74615E 78.INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 79.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B238779C03
2.438,1.479 2.677,1.292 false 2.677,1.292 2.802,1.292 false 2.823,1.229 3.094,1.406 0.271,0.177 10 false *a 2.229,0.875 2.521,1.052 0.292,0.177 10 false *b
*a Paint Mark
*b Mark Position


Align the paint mark on the front door opening trim weatherstrip LH with the mark position on the vehicle and install the front door opening trim weatherstrip LH as shown in the illustration.


Hide 62311B 80.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 81.INSTALL COWL SIDE TRIM BOARD LH

a.
B238734N01
1.792,0.448 1.948,0.646 0.156,0.198 10 false 1 1.708,1.396 1.865,1.594 0.156,0.198 10 false 2

Attach the clip and claw to install the cowl side trim board LH.

HINT:

Attach the clip and claw in the order shown in the illustration.



b.

Install the clip.


Hide 62111C 82.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 67920 83.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

a.

Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly LH.


Hide 67910 84.INSTALL DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 85.INSTALL REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)

Hide 86.INSTALL REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)

Hide 88.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION