Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261257 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rear Wiper does not Operate  


DESCRIPTION

When the glass hatch is open, the rear wiper system cuts off the power supply to prevent the rear wiper and rear washer from operating.

WIRING DIAGRAM

for 5L-E:
E377784E01
0.51,3.063 1.677,3.615 1.167,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 1.188,1.667 1.802,1.865 0.615,0.198 10 false RWMR 0.917,0.792 3.229,1.156 2.313,0.365 10 false Back Window Lock Assembly (Glass Hatch Courtesy Light Switch) 4.583,2.313 5.5,2.51 0.917,0.198 10 false WIP RR 5.573,2.469 6.49,2.667 0.917,0.198 10 false WASHER RR 5.656,1.104 6.573,1.302 0.917,0.198 10 false WASHER 5.542,0.688 6.479,0.896 0.938,0.208 10 false WIP WSH RR 3.948,0.5 4.75,0.729 0.802,0.229 10 false from Battery 3.438,0.927 4.781,1.146 1.344,0.219 10 false from IG1 NO.2 Relay 0.51,7.583 2.75,7.813 2.24,0.229 10 false Windshield Wiper Switch Assembly 4.917,7.552 6.698,7.75 1.781,0.198 10 false Rear Wiper Motor Assembly 2.698,5.802 3.01,6 0.313,0.198 10 false EW 2.656,6.26 3.115,6.458 0.458,0.198 10 false C1R 2.667,6.719 3.125,6.917 0.458,0.198 10 false +1R 4.698,6.365 5.01,6.563 0.313,0.198 10 false C1 4.708,6.823 5.021,7.021 0.313,0.198 10 false LS 4.708,7.031 4.865,7.229 0.156,0.198 10 false E 4.917,5.844 5.729,6.177 0.813,0.333 10 false Rear Wiper Relay 4.698,5.531 5.01,5.729 0.313,0.198 10 false +B 4.917,7.385 5.229,7.583 0.313,0.198 10 false Y1 0.177,8.073 3,8.292 2.823,0.219 10 false *1: for Windshield Wiper Switch LH Side Type 0.208,8.448 3.156,8.677 2.948,0.229 10 false *2: for Windshield Wiper Switch RH Side Type 0.677,5.271 1.135,5.469 0.458,0.198 10 false OFF 0.719,5.458 1.177,5.656 0.458,0.198 10 false INT 0.708,5.667 1.021,5.865 0.313,0.198 10 false ON 1.271,5.063 1.729,5.26 0.458,0.198 10 false +1R 1.615,5.063 2.073,5.26 0.458,0.198 10 false C1R 2,5.052 2.313,5.25 0.313,0.198 10 false EW 6.323,2.031 6.479,2.229 0.156,0.198 10 false 5 5.604,2.031 5.76,2.229 0.156,0.198 10 false 3 6.323,1.573 6.479,1.771 0.156,0.198 10 false 2 5.594,1.604 5.75,1.802 0.156,0.198 10 false 1 1.802,1.688 2.26,1.885 0.458,0.198 10 false G63 1.844,1.479 2.156,1.677 0.313,0.198 10 false 20 1.875,2.51 2.031,2.708 0.156,0.198 10 false A 1.823,2.292 2.135,2.49 0.313,0.198 10 false 11 3.094,5.802 3.729,5.969 0.635,0.167 10 false 7*1, 4*2 3.094,6.25 3.552,6.448 0.458,0.198 10 false 2 3.083,6.708 3.656,6.917 0.573,0.208 10 false 1*1, 3*2 4.448,5.438 4.604,5.635 0.156,0.198 10 false 5 4.469,6.25 4.625,6.448 0.156,0.198 10 false 4 4.469,6.74 4.625,6.938 0.156,0.198 10 false 2 4.469,6.958 4.625,7.156 0.156,0.198 10 false 3 1.271,2.5 1.885,2.698 0.615,0.198 10 false GND1 0.521,7.385 0.979,7.583 0.458,0.198 10 false G43 0.479,5.917 1.219,6.302 0.74,0.385 10 false Rear Wiper Switch 1.813,3.208 3.063,3.677 1.25,0.469 10 false Driver Side Junction Block Assembly 1.823,3 2.135,3.198 0.313,0.198 10 false 2D 2.896,2.375 3.052,2.573 0.156,0.198 10 false 4 0.76,2.125 1.375,2.323 0.615,0.198 10 false GOSW

except 5L-E:
E377785E01
0.469,7.833 2.729,8.042 2.26,0.208 10 false Windshield Wiper Switch Assembly 0.479,7.667 0.938,7.865 0.458,0.198 10 false G43 0.573,5.875 1.031,6.073 0.458,0.198 10 false OFF 0.594,6.073 1.052,6.271 0.458,0.198 10 false INT 0.563,6.281 0.875,6.479 0.313,0.198 10 false ON 1.125,5.698 1.583,5.896 0.458,0.198 10 false +1R 1.49,5.698 1.948,5.896 0.458,0.198 10 false C1R 1.865,5.688 2.177,5.885 0.313,0.198 10 false EW 2.552,6.417 2.865,6.615 0.313,0.198 10 false EW 2.521,6.802 2.979,7 0.458,0.198 10 false C1R 2.51,7.167 2.969,7.365 0.458,0.198 10 false +1R 4.74,6.938 5.052,7.135 0.313,0.198 10 false C1 4.75,7.281 5.063,7.479 0.313,0.198 10 false LS 4.76,7.604 4.917,7.802 0.156,0.198 10 false E 5.031,6.688 5.75,7.125 0.719,0.438 10 false Rear Wiper Relay 4.76,6.521 5.073,6.719 0.313,0.198 10 false +B 4.5,6.406 4.656,6.604 0.156,0.198 10 false 5 4.51,6.813 4.667,7.01 0.156,0.198 10 false 4 4.51,7.146 4.667,7.344 0.156,0.198 10 false 2 4.5,7.469 4.656,7.667 0.156,0.198 10 false 3 2.021,4.417 2.635,4.615 0.615,0.198 10 false G216 2.115,4.198 2.427,4.396 0.313,0.198 10 false 19 2.094,3.604 2.25,3.802 0.156,0.198 10 false A 2.052,3.396 2.365,3.594 0.313,0.198 10 false 11 2.375,4.01 4.688,4.229 2.313,0.219 10 false Driver Side Junction Block Assembly 2.229,2.844 2.854,3.094 0.625,0.25 10 false WIP RR 2.781,2.979 3.698,3.177 0.917,0.198 10 false WASHER RR 3.615,2.396 4.313,2.656 0.698,0.26 10 false WASHER 4.833,1.781 5.146,1.979 0.313,0.198 10 false 2O 4.865,1.583 5.177,1.781 0.313,0.198 10 false 27 4.854,0.563 5.167,0.76 0.313,0.198 10 false 2K 4.844,3.146 5.156,3.344 0.313,0.198 10 false 2M 4.917,2.948 5.073,3.146 0.156,0.198 10 false 5 4.885,0.365 5.042,0.563 0.156,0.198 10 false 1 1.427,4.438 2.042,4.635 0.615,0.198 10 false RWMR 0.542,4.844 2.188,5.25 1.646,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 1.469,3.604 2.083,3.802 0.615,0.198 10 false GND1 2.708,0.104 6.844,0.323 4.135,0.219 10 false Back Window Lock Assembly (Glass Hatch Courtesy Light Switch) 6.031,0.552 6.875,0.729 0.844,0.177 10 false from Battery 2.729,1.583 4,1.833 1.271,0.25 10 false IG NO.5 Relay 0.156,8.146 3,8.344 2.844,0.198 10 false *1: for Windshield Wiper Switch LH Side Type 0.188,8.469 3.26,8.677 3.073,0.208 10 false *2: for Windshield Wiper Switch RH Side Type 4.99,8.01 5.302,8.208 0.313,0.198 10 false Y1 5.01,8.177 6.792,8.427 1.781,0.25 10 false Rear Wiper Motor Assembly 2.958,6.406 3.594,6.604 0.635,0.198 10 false 7*1, 4*2 2.938,6.802 3.396,7 0.458,0.198 10 false 2 2.938,7.156 3.521,7.354 0.583,0.198 10 false 1*1, 3*2 0.396,6.552 1.135,6.906 0.74,0.354 10 false Rear Wiper Switch 4.854,3.604 5.167,3.802 0.313,0.198 10 false 2N 4.917,3.417 5.073,3.615 0.156,0.198 10 false 1 0.917,0.948 1.531,1.146 0.615,0.198 10 false GOSW

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (GLASS HATCH COURTESY SWITCH)
a.

Use the Data List to check if the glass hatch opener is functioning properly (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Glass Hatch Courtesy Switch Glass hatch courtesy switch signal / ON or OFF ON: Glass hatch open
OFF: Glass hatch closed
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.


Result
Result Proceed to
OK A
NG (for 5L-E) B
NG (except 5L-E) C


A

2.PERFORM ACTIVE TEST USING GTS (REAR WIPER MOTOR)

B

C

2.PERFORM ACTIVE TEST USING GTS (REAR WIPER MOTOR)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Rear Wiper Power Supply WASHER RR relay operation ON/OFF -

OK:

Rear wiper motor operates.


Result
Result Proceed to
OK A
NG (for 5L-E) B
NG (except 5L-E) C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

3.INSPECT WASHER RR RELAY

C

11.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
3.INSPECT WASHER RR RELAY
a.

Remove the WASHER RR relay from the engine room relay block, junction block.




OK

4.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - BATTERY)

NG

REPLACE WASHER RR RELAY

4.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - BATTERY)
a.
B242123E01
0.349,0.148 0.526,0.311 0.177,0.163 10 *a

Remove the WASHER RR relay from the engine room relay block, junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
WASHER RR relay terminal 2 - Body ground Ignition switch ON 11 to 14 V
WASHER RR relay terminal 2 - Body ground Ignition switch off Below 1 V
WASHER RR relay terminal 5 - Body ground Ignition switch ON 11 to 14 V
WASHER RR relay terminal 5 - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to WASHER RR Relay)



OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - WASHER RR RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - WASHER RR RELAY AND BODY GROUND)
a.

Disconnect the G63 main body ECU (multiplex network body ECU) connector.


b.

Remove the WASHER RR relay from the engine room relay block, junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G63-20 (RWMR) - WASHER RR relay terminal 1 Always Below 1 Ω
G63-20 (RWMR) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - REAR WIPER MOTOR ASSEMBLY)

NG

18.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
6.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - REAR WIPER MOTOR ASSEMBLY)
a.

Disconnect the Y1 rear wiper motor assembly connector.


b.

Remove the WASHER RR relay from the engine room relay block, junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-5 (+B) - WASHER RR relay terminal 3 Always Below 1 Ω
Y1-5 (+B) - Body ground Always 10 kΩ or higher




OK

7.INSPECT REAR WIPER MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR WIPER MOTOR ASSEMBLY
a.

Remove the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>REMOVAL


b.

Inspect the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>INSPECTION



OK

8.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPLACE REAR WIPER MOTOR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND)
a.
U116476E03
1.969,1.021 2.354,0.635 2.354,0.635 2.521,0.635 true 2.646,0.552 2.771,0.708 0.125,0.156 10 false E 0.115,0.052 0.313,0.24 0.198,0.188 10 false *a 0.615,1.083 0.813,1.229 0.198,0.146 10 false Y1

Disconnect the rear wiper motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-3 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Rear Wiper Motor Assembly)



OK

9.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
a.

Remove the windshield wiper switch assembly.

Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL


b.

Inspect the windshield wiper switch assembly.

Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>INSPECTION



OK

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - REAR WIPER MOTOR ASSEMBLY AND BODY GROUND)

NG

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - REAR WIPER MOTOR ASSEMBLY AND BODY GROUND)
a.

for Windshield Wiper Switch LH Side Type:

i.

Disconnect the Y1 rear wiper motor assembly connector.


ii.

Disconnect the G43 windshield wiper switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-2 (LS) - G43-1 (+1R) Always Below 1 Ω
Y1-4 (C1) - G43-2 (C1R) Always Below 1 Ω
G43-7 (EW) - Body ground Always Below 1 Ω
Y1-2 (LS) - Body ground Always 10 kΩ or higher
Y1-4 (C1) - Body ground Always 10 kΩ or higher




b.

for Windshield Wiper Switch RH Side Type:

i.

Disconnect the Y1 rear wiper motor assembly connector.


ii.

Disconnect the G43 windshield wiper switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-2 (LS) - G43-3 (+1R) Always Below 1 Ω
Y1-4 (C1) - G43-2 (C1R) Always Below 1 Ω
G43-4 (EW) - Body ground Always Below 1 Ω
Y1-2 (LS) - Body ground Always 10 kΩ or higher
Y1-4 (C1) - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the driver side junction block assembly connectors.

E377931C01
1.833,0.115 2.198,0.333 0.365,0.219 1.781,1.427 2.146,1.646 0.365,0.219 5.01,0.115 5.375,0.333 0.365,0.219 5,1.448 5.365,1.667 0.365,0.219 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 1.927,0.135 2.24,0.333 0.313,0.198 10 false 2K 1.875,1.448 2.188,1.646 0.313,0.198 10 false 2N 5.083,1.479 5.396,1.677 0.313,0.198 10 false 2O 5.083,0.135 5.396,0.333 0.313,0.198 10 false 2M
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2K-1 - Body ground Always 11 to 14 V
2O-27 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
2M-5 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2N-1 - Body ground Always Below 1 Ω




OK

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2O driver side junction block assembly connector.


b.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G216-19 (RWMR) - 2O-27 Always Below 1 Ω
A-11 (GND1) - Body ground Always Below 1 Ω
G216-19 (RWMR) - Body ground Always 10 kΩ or higher




OK

13.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - REAR WIPER MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - REAR WIPER MOTOR ASSEMBLY)
a.

Disconnect the Y1 rear wiper motor assembly connector.


b.

Disconnect the 2M driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-5 (+B) - 2M-5 Always Below 1 Ω
Y1-5 (+B) - Body ground Always 10 kΩ or higher




OK

14.INSPECT REAR WIPER MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT REAR WIPER MOTOR ASSEMBLY
a.

Remove the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>REMOVAL


b.

Inspect the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>INSPECTION



OK

15.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPLACE REAR WIPER MOTOR ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND)
a.
U116476E03
1.969,1.021 2.354,0.635 2.354,0.635 2.521,0.635 true 2.646,0.552 2.771,0.708 0.125,0.156 10 false E 0.115,0.052 0.313,0.24 0.198,0.188 10 false *a 0.615,1.083 0.813,1.229 0.198,0.146 10 false Y1

Disconnect the rear wiper motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-3 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Rear Wiper Motor Assembly)



OK

16.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
a.

Remove the windshield wiper switch assembly.

Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL


b.

Inspect the windshield wiper switch assembly.

Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>INSPECTION



OK

17.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - REAR WIPER MOTOR ASSEMBLY AND BODY GROUND)

NG

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - REAR WIPER MOTOR ASSEMBLY AND BODY GROUND)
a.

for Windshield Wiper Switch LH Side Type:

i.

Disconnect the Y1 rear wiper motor assembly connector.


ii.

Disconnect the G43 windshield wiper switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-2 (LS) - G43-1 (+1R) Always Below 1 Ω
Y1-4 (C1) - G43-2 (C1R) Always Below 1 Ω
G43-7 (EW) - Body ground Always Below 1 Ω
Y1-2 (LS) - Body ground Always 10 kΩ or higher
Y1-4 (C1) - Body ground Always 10 kΩ or higher




b.

for Windshield Wiper Switch RH Side Type:

i.

Disconnect the Y1 rear wiper motor assembly connector.


ii.

Disconnect the G43 windshield wiper switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-2 (LS) - G43-3 (+1R) Always Below 1 Ω
Y1-4 (C1) - G43-2 (C1R) Always Below 1 Ω
G43-4 (EW) - Body ground Always Below 1 Ω
Y1-2 (LS) - Body ground Always 10 kΩ or higher
Y1-4 (C1) - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.
E379756C01
1.552,0.24 1.906,0.49 0.354,0.25 1.563,2.021 1.917,2.271 0.354,0.25 1.25,2.656 1.615,3.115 1.615,3.115 1.844,3.115 true 1.646,0.271 1.958,0.469 0.313,0.198 10 false 2D 1.698,2.052 2.01,2.25 0.313,0.198 10 false A 1.917,3.042 2.531,3.24 0.615,0.198 10 false GND1 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a
*a Component without harness connected
(Driver Side Junction Block Assembly)


Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-4 - A-11 (GND1) Always Below 1 Ω
A-11 (GND1) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU]

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY