for 2TR-FE:
The driving support ECU assembly receives yaw rate sensor (airbag sensor assembly) signals from the yaw rate sensor and skid control ECU (brake actuator assembly) via CAN communication. If the driving support ECU assembly receives a yaw rate sensor malfunction signal from the yaw rate sensor (airbag sensor assembly) or skid control ECU (brake actuator assembly), DTC C1A46 will be stored.
except 2TR-FE:
The driving support ECU assembly receives yaw rate sensor (airbag sensor assembly) signals from the yaw rate sensor and skid control ECU (master cylinder solenoid) via CAN communication. If the driving support ECU assembly receives a yaw rate sensor malfunction signal from the yaw rate sensor (airbag sensor assembly) or skid control ECU (master cylinder solenoid), DTC C1A46 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A46 | Yaw Rate Sensor | ·
While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor (airbag sensor assembly) malfunction signal from yaw rate sensor (airbag sensor assembly) for approximately 10 seconds. ·
for 2TR-FE: While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor (airbag sensor assembly) zero point malfunction signal from skid control ECU (brake actuator assembly) for approximately 10 seconds. ·
except 2TR-FE: While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor (airbag sensor assembly) zero point malfunction signal from skid control ECU (master cylinder solenoid) for approximately 10 seconds. |
·
Vehicle stability control system ·
Yaw rate sensor (airbag sensor assembly) ·
Skid control ECU assembly (brake actuator assembly) (for 2TR-FE) ·
Skid control ECU assembly (master cylinder solenoid) (except 2TR-FE) ·
Driving support ECU assembly |
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Pre-crash safety system DTC C1A46 may be stored due to a malfunction in the vehicle stability control system. Therefore, it is necessary to check for and troubleshoot vehicle stability control system DTCs first.
Check for DTCs.
for 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR
except 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTC are output (for 2TR-FE) | B |
| Vehicle stability control system DTC are output (except 2TR-FE) | C |
A
B
C
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A46 is not output | A |
| DTC C1A46 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the driving support ECU assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A46 is not output | A |
| DTC C1A46 is output | B |
A
B
Replace the yaw rate sensor (airbag sensor assembly).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A46 is not output | A |
| DTC C1A46 is output (for 2TR-FE) | B |
| DTC C1A46 is output (except 2TR-FE) | C |
A
B
C
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>DISASSEMBLY
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>DISASSEMBLY